[논문]Effect of Annealing on the Pitting Corrosion Resistance of Anodized Aluminum-Magnesium Alloy Processed by Equal Channel Angular Pressing

Son, In-Joon; Nakano, Hiroaki; Oue, Satoshi; Kobayashi, Shigeo; Fukushima, Hisaaki; Horita, Zenji

Effect of Annealing on the Pitting Corrosion Resistance of Anodized Aluminum-Magnesium Alloy Processed by Equal Channel Angular Pressing 원문보기

Corrosion science and technology, v.6 no.6, 2007년, pp.275 - 281

Son, In-Joon (Department of Materials Process Engineering, Graduate School of Engineering, Kyushu University) , Nakano, Hiroaki (Department of Materials Science & Engineering, Faculty of Engineering, Kyushu University) , Oue, Satoshi (Department of Materials Science & Engineering, Faculty of Engineering, Kyushu University) , Kobayashi, Shigeo (Department of Applied Chemistry and Biochemistry, Faculty of Engineering, Kyushu Sangyo University) , Fukushima, Hisaaki (Department of Materials Science & Engineering, Faculty of Engineering, Kyushu University) , Horita, Zenji (Department of Materials Science & Engineering, Faculty of Engineering, Kyushu University)

Abstract ▼ AI-Helper

The effect of annealing on the pitting corrosion resistance of anodized Al-Mg alloy (AA5052) processed by equal-channel angular pressing (ECAP) was investigated by electrochemical techniques in a solution containing 0.2 mol/L of $AlCl_3$ and also by surface analysis. The Al-Mg alloy was annealed at a fixed temperature between 473 and 573 K for 120 min in air after ECAP. Anodizing was conducted for 40 min at $100-400A/m^2$ at 293 K in a solution containing 1.53 mol/L of $H_2SO_4$ and 0.0185 mol/L of $Al_2(SO_4)_3$. The internal stress generated in anodic oxide films during anodization was measured with a strain gauge to clarify the effect of ECAP on the pitting corrosion resistance of anodized Al-Mg alloy. The time required to initiate the pitting corrosion of anodized Al-Mg alloy was shorter in samples subjected to ECAP, indicating that ECAP decreased the pitting corrosion resistance. However, the pitting corrosion resistance was greatly improved by annealing after ECAP. The time required to initiate pitting corrosion increased with increasing annealing temperature. The strain gauge attached to Al-Mg alloy revealed that the internal stress present in the anodic oxide films was compressive stress, and that the stress was larger with ECAP than without. The compressive internal stress gradually decreased with increasing annealing temperature. Scanning electron microscopy showed that cracks occurred in the anodic oxide film on Al-Mg alloy during initial corrosion and that the cracks were larger with ECAP than without. The ECAP process of severe plastic deformation produces large internal stresses in the Al-Mg alloy; the stresses remain in the anodic oxide films, increasingthe likelihood of cracks. It is assumed that the pitting corrosion is promoted by these cracks as a result of the higher internal stress resulting from ECAP. The improvement in the pitting corrosion resistance of anodized AlMg alloy as a result of annealing appears to be attributable to a decrease in the internal stresses in anodic oxide films

주제어

AI 본문요약
AI-Helper

* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.

제안 방법

In this study, the mechanism of the change in the pitting corrosion resistance of anodized Al-Mg alloy with ECAP was clarified by surface analysis and the internal stress in the anodic oxide film estimated by using a strain gauge. The Al-Mg alloy was subjected to annealing after ECAP in an attempt to improve the pitting corrosion resistance of anodized Al-Mg alloy.
The Al-Mg alloy samples were annealed at a fixed temperature of 473, 523, or 573 K for 120 min in air atmosphere after ECAP. The morphology of anodized Al-Mg alloy with and without ECAP and the morphology of pitting corrosion were analyzed by FE-SEM and SEM.

참고문헌 (13)

H.H. Uhlig: Corrosion and Corrosion Control (in Japanese, Sangyo Tosho, Tokyo, 1968) pp.320-332
G. Ito: Corrosion Science and Engineering (in Japanese, Corona Publishing Co., Tokyo, 1973) pp.306-315
T. Asada: J. Met. Finish. Soc. Jpn. 21, 490-497 (1970)

상세보기
N. Baba: Anodic Oxide Films Produced by Electrolysis (in Japanese, Maki Syoten, Tokyo, 1996) pp.14-47
R.Z. Valiev, N.A. Krasilnikov and N.K. Tsenev: Mater. Sci. Eng. A137, 35-41 (1991)
R.Z. Valiev, R.K. Islamgaliev and I.V. Alexandrov: Prog. Mater. Sci. 45, 103-109 (2000)

상세보기
Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran and T.C. Lowe: Ultrafine Grained Materials II, The Minerals, Metals & Materials Society, Warrendale, PA,(2002)
Z. Horita, M. Furukawa, M. Nemoto and T.G. Langdon: Mater. Sci. Tach. 16, 1239-1245 (2000)

상세보기
I.J. Son, H. Nakano, S. Oue, S. Kobayashi, H. Fukushima and Z. Horita: J. Japan Inst. Metal. 70, 534-540 (2006)

상세보기
I.J. Son, H. Nakano, S. Oue, S. Kobayashi, H. Fukushima and Z. Horita: Mater. Trans. 48, 21-28 (2007)

상세보기
Z. Horita, T. Fujinami, M. Nemoto and T.G. Langdon: Metallurgical and Mater. Trans. A 31A, 691-701 (2000)
I.J. Son, H. Nakano, S. Oue, S. Kobayashi, H. Fukushima and Z. Horita: Mater. Trans. 47, 1163-1169 (2006)

상세보기
M. Seo and K. Ueno: J. Finish. Soc. Jpn. 51, 365-370 (2000)

원문 URL 링크

한국학술정보 : 저널
한국부식방식학회 : 저널
Korea Open Access Journals : 저널

*원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다.

내보내기 메뉴

내보내기 구분

파일저장
인쇄
메일전송

구성항목

기본정보
상세정보

관리번호, 논문명, 저널/프로시딩명, 저자 , 발행년, 권, 호, 시작페이지, 끝페이지, 발행기관

저장형식

Text(ASCII format)
Excel format
RefWorks Direct Export
RIS format (for Reference Manager, ProCite, EndNote), Scholar's Aids, Mendeley

메일정보

받는사람 (필수): @
보내는사람 (선택): @
제목
내용: KISTI 검색결과 이메일 서비스

안내

총 건의 자료가 검색되었습니다.

다운받으실 자료의 인덱스를 입력하세요. (1-10,000)

검색결과의 순서대로 최대 10,000건 까지 다운로드가 가능합니다.

데이타가 많을 경우 속도가 느려질 수 있습니다.(최대 2~3분 소요)

다운로드 파일은 UTF-8 형태로 저장됩니다.
파일의 내용이 제대로 보이지 않을실 때는 웹브라우저 상단의 보기 -> 인코딩 -> 자동선택 여부를 확인하십시오.

Text(ASCII format)
Excel format

표제어: PCR

동의어: Packet Collision Rate

용어 설명 출처 목록 (6)

용어 설명: PCR은 세균 특이성이 있는 primer를 이용하여 적은 수의 세균이 있을지라도 쉽게 검출할 수 있는 유용한 방법이며, 이를 이용하여 구강 내 치면세균막이나 타액에서 직접 세균을 검출할 수 있게 되었다[8].

AI-Helper ※ AI-Helper는 을 사용합니다.

AI-Helper

안녕하세요, AI-Helper입니다. 좌측 "선택된 텍스트"에서 텍스트를 선택하여 요약, 번역, 용어설명을 실행하세요.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.

연합인증