$\require{mediawiki-texvc}$
  • 검색어에 아래의 연산자를 사용하시면 더 정확한 검색결과를 얻을 수 있습니다.
  • 검색연산자
검색연산자 기능 검색시 예
() 우선순위가 가장 높은 연산자 예1) (나노 (기계 | machine))
공백 두 개의 검색어(식)을 모두 포함하고 있는 문서 검색 예1) (나노 기계)
예2) 나노 장영실
| 두 개의 검색어(식) 중 하나 이상 포함하고 있는 문서 검색 예1) (줄기세포 | 면역)
예2) 줄기세포 | 장영실
! NOT 이후에 있는 검색어가 포함된 문서는 제외 예1) (황금 !백금)
예2) !image
* 검색어의 *란에 0개 이상의 임의의 문자가 포함된 문서 검색 예) semi*
"" 따옴표 내의 구문과 완전히 일치하는 문서만 검색 예) "Transform and Quantization"
쳇봇 이모티콘
안녕하세요!
ScienceON 챗봇입니다.
궁금한 것은 저에게 물어봐주세요.

논문 상세정보

Abstract

In this work, component characteristics of a reheat cycle gas turbine in a commercial combined cycle power plant were evaluated. An inverse performance analysis, in which component characteristic parameters were estimated based on measured performance data, was carried out. The measured parameters were the power, the fuel flow rates of two combustors, and the temperatures and pressures at various locations such as the compressor discharge, exits of both the high- and low-pressure turbines. The estimated parameters from the analysis include the compressor and turbine efficiencies and the inlet air flow rate. The analysis was performed for a wide operation range in terms of the ambient temperature and load, providing a database for the variations of the characteristic parameters with changes in the operating condition. In addition, a sensitivity analysis was performed to examine the influence of the uncertainties of the measured parameters on the estimated parameters. The analysis program can be further developed into a performance diagnosis tool and the obtained component characteristic data can be used as reference database.

참고문헌 (14)

  1. R. Bettochi and P. R. Spina, Diagnosis of gas turbine operating conditions by means of the inverse cycle calculation, Proc. of ASME Turbo Expo, Indianapolis, USA, (1999) ASME paper 99-GT-185 
  2. E. Jeffs, Korean combined cycle is commercial launch of GT24, Turbomachinery International, (March/April) (1996) 23-24 
  3. T. S. Kim and S. T. Ro, The effect of gas turbine coolant modulation on the part load performance of combined cycle plants - part 1 : gas turbines, J. of Power and Energy, 211 (1998) 443-451 
  4. H. Koerbaecher, A. Pfeiffer, and T. Rothe, Development and validation of the new Alstom GT24/GT26 upgrade compressor, Proc. of ASME Turbo Expo, Reno, USA, (2005) ASME paper GT2005-68795 
  5. Y. G. Li, P. Pilidis and M. A. Newby, An adaptation for gas turbine design-point performance simulation, Proc. of ASME Turbo Expo, Reno, USA, (2005) ASME paper GT2005-68140 
  6. A. Stamatis, K. Mathioudakis and K. D. Papailiou, Adaptive simulation of gas turbine performance, J. of Engineering for Gas Turbines and Power, 112 (1990) 168-175 
  7. K. Mathioudakis, A. Stamatis, A. Tsalavoutas and N. Aretakis, Performance analysis of industrial gas turbines for engine condition monitoring, J. of Power and Energy, (215) 173-184 
  8. S. H. Yoon, D. H. Jeong and T. S. Kim, Analysis of operation conditions of a reheat cycle gas turbine for a combined cycle power plant, J. of Fluid Machinery (in Korean), 9 (6) (2006) 34-44 
  9. F. Joos, P. Brunner, B. Schulte-Werning, K. Syed and A. Eroglu, Development of the sequential combustion system for the GT24/GT26 gas turbine family, ABB review (4) (1998) 4-16 
  10. J. H. Kim, Analysis on transient behavior of gas turbines for power generation, Ph. D. Thesis, Seoul National Univ., Korea, (2000) 
  11. B. R. Roth, D. L. Doel, D. Mavris and D. Beeson, High-accuracy matching of engine performance models to test data, Proc. of ASME Turbo Expo, Atlanta, USA, (2003) ASME paper GT2003-38784 
  12. Y. G. Li, Performance-analysis-based gas turbine diagnostics: a review, J. of Power and Energy, 216 (2002) 363-374 
  13. J. J. Lee, J. E. Yoon, T. S. Kim and J. L. Sohn, Performance test and component characteristics evaluation of a micro gas turbine, J. of Mechanical Science and Technology, 21 (1) (2006) 141-152 
  14. A. Mayer and S. Van der Linden, GT24/26 advanced cycle system power plant progress for the new millennium, Proc. of ASME Turbo Expo, Indianapolis, USA, (1999) ASME paper 99-GT-404 

이 논문을 인용한 문헌 (2)

  1. Kim, Jae-Hwan 2009. "" 유체기계저널 = Journal of fluid machinery, 12(1): 70~75 
  2. Lee, Hyun-Seung ; Lee, Young-Shin 2012. "Design Optimization on End Coupling as a Power Transmission Component for Aluminum Hot Rolling Process" 한국CAD/CAM학회논문집 = Transactions of the Society of CAD/CAM Engineers, 17(1): 1~6 

원문보기

원문 PDF 다운로드

  • 원문 PDF 정보가 존재하지 않습니다.

원문 URL 링크

원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다. (원문복사서비스 안내 바로 가기)

상세조회 0건 원문조회 0건

이 논문과 연관된 기능

DOI 인용 스타일