$\require{mediawiki-texvc}$
  • 검색어에 아래의 연산자를 사용하시면 더 정확한 검색결과를 얻을 수 있습니다.
  • 검색연산자
검색연산자 기능 검색시 예
() 우선순위가 가장 높은 연산자 예1) (나노 (기계 | machine))
공백 두 개의 검색어(식)을 모두 포함하고 있는 문서 검색 예1) (나노 기계)
예2) 나노 장영실
| 두 개의 검색어(식) 중 하나 이상 포함하고 있는 문서 검색 예1) (줄기세포 | 면역)
예2) 줄기세포 | 장영실
! NOT 이후에 있는 검색어가 포함된 문서는 제외 예1) (황금 !백금)
예2) !image
* 검색어의 *란에 0개 이상의 임의의 문자가 포함된 문서 검색 예) semi*
"" 따옴표 내의 구문과 완전히 일치하는 문서만 검색 예) "Transform and Quantization"
쳇봇 이모티콘
안녕하세요!
ScienceON 챗봇입니다.
궁금한 것은 저에게 물어봐주세요.

논문 상세정보

Abstract

Surface recombination loss should be reduced for high efficiency of solar cells. To reduce this loss, the BSF (back surface field) is used. The BSF on the back of the p-type wafer forms a p+layer, which prevents the activity of electrons of the p-area for the rear recombination. As a result, the leakage current is reduced and the rear-contact has a good Ohmic contact. Therefore, the open-circuit-voltage (Voc) and fill factor (FF) of solar cells are increased. This paper investigates the formation of the rear contact process by comparing aluminum-paste (Al-paste) with pure aluminum-metal(99.9%). Under the vacuum evaporation process, pure aluminum-metal(99.9%) provides high conductivity and low contact resistance of $4.2\;m{\Omega}cm$, but It is difficult to apply the standard industrial process to it because high vacuum is needed, and it's more expensive than the commercial equipment. On the other hand, using the Al-paste process by screen printing is simple for the formation of metal contact, and it is possible to produce the standard industrial process. However, Al-paste used in screen printing is lower than the conductivity of pure aluminum-metal(99.9) because of its mass glass frit. In this study, contact resistances were measured by a 4-point probe. The contact resistance of pure aluminum-metal was $4.2\;m{\Omega}cm$ and that of Al-paste was $35.69\;m{\Omega}cm$. Then the rear contact was analyzed by scanning electron microscope (SEM).

참고문헌 (5)

  1. J. G. Fossum, IEEE Trans. Electron. Devices ED-24, 322 (1977). 
  2. Z. Makaro, G. Battistig, Z. E. Horvath, J. Likonen, and I. Barsony, Vacuum 50, 481 (1998). 
  3. C. S. Chen and D. K. Schroder, J. Appl. Phys. 71, 5858 (1992). 
  4. A. Morales-Acevedoa, G. Santanaa,, A. Martela, L. Hernandez, Solid-State Electron. 43, 2075 (1999). 
  5. J. del Alamo, J. Eguren, and A. Luque, Solid-State Electron. 24, 415 (1981). 

이 논문을 인용한 문헌 (2)

  1. 2011. "Evaluation of Solar Cell Properties of Poly-Si Thin Film Fabricated with Novel Process Conditions for Solid Phase Crystallization" 전기전자재료학회논문지 = Journal of the Korean institute of electronic material engineers, 24(9): 766~772 
  2. Jeong, Ji-Hyun ; Kim, Sung-Jin ; Son, Chang-Rok ; Ur, Soon-Chul ; Kweon, Soon-Yong 2011. "Thermal Process Optimization of Pb-free Ag-paste and Evaluation of Electrical Properties in Mono-Si Solar Cell" 전기전자재료학회논문지 = Journal of the Korean institute of electronic material engineers, 24(10): 844~849 

DOI 인용 스타일