3-Amino-1,2,4-triazole(ATA)을 비상용성 블렌드인 maleated HDPE(mHDPE)/maleated EPDM (mEPDM)(50 wt%/50 wt%)에 용융혼합에 의해 2.5 phr, 5.0 phr 첨가하였으며, ATA 첨가에 따른 블렌드의 미세구조, 기계적물성 및 유변물성을 FT-IR, FE-SEM, 인장시험, DMA 및 ARES를 이용하여 각각 조사하였다. FTIR 및 DMA 분석결과 용융혼합 과정에서 ATA가 mHDPE 및 mEPDM의 말레무수물과 반응하여 초분자적 수소결합이 형성되며, 이로부터 물리적 가교구조가 형성되는 것을 알 수 있었다. FE-SEM 분석결과 mHDPE/mEPDM 블렌드는 플라스틱인 HDPE가 연속상을 이루고 고무상인 EPDM이 분산상을 이루며 ATA를 첨가함으로써 모폴로지가 더욱 미세해짐을 알 수 있었다. 인장물성시험결과 ATA에 첨가에 의해 형성된 물리적가교구조로 인해 인장강도, 모듈러스, 파단신율 값 및 탄성복원력이 증가되었으며, 용융레올로지 특성 분석결과 ATA가 첨가됨으로써 블렌드의 저장탄성율과 용융점도가 증가됨을 알 수 있었다.
3-Amino-1,2,4-triazole(ATA)을 비상용성 블렌드인 maleated HDPE(mHDPE)/maleated EPDM (mEPDM)(50 wt%/50 wt%)에 용융혼합에 의해 2.5 phr, 5.0 phr 첨가하였으며, ATA 첨가에 따른 블렌드의 미세구조, 기계적물성 및 유변물성을 FT-IR, FE-SEM, 인장시험, DMA 및 ARES를 이용하여 각각 조사하였다. FTIR 및 DMA 분석결과 용융혼합 과정에서 ATA가 mHDPE 및 mEPDM의 말레무수물과 반응하여 초분자적 수소결합이 형성되며, 이로부터 물리적 가교구조가 형성되는 것을 알 수 있었다. FE-SEM 분석결과 mHDPE/mEPDM 블렌드는 플라스틱인 HDPE가 연속상을 이루고 고무상인 EPDM이 분산상을 이루며 ATA를 첨가함으로써 모폴로지가 더욱 미세해짐을 알 수 있었다. 인장물성시험결과 ATA에 첨가에 의해 형성된 물리적가교구조로 인해 인장강도, 모듈러스, 파단신율 값 및 탄성복원력이 증가되었으며, 용융레올로지 특성 분석결과 ATA가 첨가됨으로써 블렌드의 저장탄성율과 용융점도가 증가됨을 알 수 있었다.
3-Amino-1,2,4-triazole (ATA) (2.5 and 5.0 phr) was incorporated into a immiscible maleated ethylene propylene diene rubber(mEPDM)/maleated high density polyethylene(mHDPE) (50 wt%/50 wt%) blend by melt mixing. Effects of the ATA on structure, mechanical and rheological properties of the blend was in...
3-Amino-1,2,4-triazole (ATA) (2.5 and 5.0 phr) was incorporated into a immiscible maleated ethylene propylene diene rubber(mEPDM)/maleated high density polyethylene(mHDPE) (50 wt%/50 wt%) blend by melt mixing. Effects of the ATA on structure, mechanical and rheological properties of the blend was investigated. FT-IR and DMA results revealed that supramolecular hydrogen bonding interactions between the polymer chains occur by reaction of ATA with maleic anhydride grafted onto the component polymers in the blend, which induces the physical crosslinks in the blend. FE-SEM analysis showed that mEPDM forms a dispersed phase in continuous mHDPE matrix, and the blend with the ATA has finer phase morphology as compared to the blend without the ATA. By the addition of ATA in the blend, there were significant increases in tensile strength, modulus and elongation-at-break as well as elastic recoverability. Melt rheology studies revealed that ATA induced substantial increase in storage modulus and complex viscosity of the blend at the melt state.
3-Amino-1,2,4-triazole (ATA) (2.5 and 5.0 phr) was incorporated into a immiscible maleated ethylene propylene diene rubber(mEPDM)/maleated high density polyethylene(mHDPE) (50 wt%/50 wt%) blend by melt mixing. Effects of the ATA on structure, mechanical and rheological properties of the blend was investigated. FT-IR and DMA results revealed that supramolecular hydrogen bonding interactions between the polymer chains occur by reaction of ATA with maleic anhydride grafted onto the component polymers in the blend, which induces the physical crosslinks in the blend. FE-SEM analysis showed that mEPDM forms a dispersed phase in continuous mHDPE matrix, and the blend with the ATA has finer phase morphology as compared to the blend without the ATA. By the addition of ATA in the blend, there were significant increases in tensile strength, modulus and elongation-at-break as well as elastic recoverability. Melt rheology studies revealed that ATA induced substantial increase in storage modulus and complex viscosity of the blend at the melt state.
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
제안 방법
01 to 100 at 150℃. For the observation of phase morphology of the blend, the sample was fractured cryogenically and the fractured surface was etched using xylene at room temperature for 6 hours to remove the EPDM phase. Phase morphology of the blends was observed using a JEOL JSM-630F instrument.
At least 10 samples were tested to ensure the reproducibility of the results. Tension set was measured to evaluate elastic recoverability of the samples. The samples were stretched to 100% elongation and keeping them in that position for 10 min, and length of the sample after the release of the applied stress was measured.
이론/모형
For the observation of phase morphology of the blend, the sample was fractured cryogenically and the fractured surface was etched using xylene at room temperature for 6 hours to remove the EPDM phase. Phase morphology of the blends was observed using a JEOL JSM-630F instrument. IR analysis was carried out on a thin film using a Varian 800 FT-IR in frequency range of 400 - 4000 cm-1.
성능/효과
When the polymer melt is deformed at higher frequency, polymer chains do not have less time to relax, so the modulus goes up. The results show that the blend with ATA has higher storage modulus as compared to that without ATA, and the modulus increases with increasing ATA content, especially at low frequency region, and the increase in the modulus is accompanied with a decrease in the terminal region slope. The higher modulus and smaller terminal slope of the blend with ATA over the blend without ATA indicate the formation of a three dimensional network structure in the blend with ATA.
참고문헌 (26)
S. K. De and A. K. Bhowmick Ed, "Thermoplastic Elastomers from Rubber-Plastic Blends" Ellis Horwood, New York, 1990.
B. C. Kim, S. S. Hwang, K. Y. Lim, and K. J, Yoon, "Toughening of PP/EPDM blend by compatibilization", J. Appl. Polym. Sci., 78, 1267 (2000).
H. Ismail and Suryadiansyah, "Thermoplastic elastomers based on polypropylene/natural rubber and polypropylene/recycle rubber blends", Polym. Test., 21, 389 (1996).
A. L. N. Da Silva, M. C. G. Rocha, F. M. B. Coutinho, R. E.S. Bretas, and M. Farah, "Evaluation of rheological and mechanical behavior of blends based on polypropylene and metallocene elastomers", Polym. Test., 21, 647 (2002).
Z. S. Fu, Z. Q. Fan, Y.Q. Zhang, and L. X. Feng, "Structure and morphology of polypropylene/poly(ethylene-co-propylene) in-situ blends synthesized by spherical Ziegler-Natta catalyst", Eur. Polym. J., 39, 795 (2003).
E. Prut, T. Medintseva, and V. Dreval, "Mechanical and rheological behavior of unvulcanized and dynamically vulcanized i-PP/EPDM blends", Macromol. Symp., 233, 78 (2006).
Y. Chen, C. Xu, L. Cao, Y. Wang, and X. Cao, "PP/EPDMbased dynamically vulcanized thermoplastic olefin with zinc dimethacrylate: preparation, rheology, morphology, crystallization and mechanical properties", Polym. Test., 31, 728 (2012).
S. George, R. Joseph, S. Thomas, and K.T. Varughese, "Blends of isotactic polypropylene and nitrile rubber: morphology, mechanical properties and compatibilization", Polymer, 36, 4405 (1995).
Z. Su, P. Jiang, Q. Li, P. Wei, G. Wang, and Y. Zhang, "Mechanical properties and morphological structures relationship of blends based on sulfated EPDM ionomer and polypropylene", J. Appl. Polym. Sci., 94, 1504 (2004).
P. Antony, S. Bandyopadhyay, and S. K. De, "Thermoplastic elastomers based on ionomeric polyblends of zinc salts of maleated polypropylene and maleated EPDM rubber", Polym. Eng. Sci., 39, 963 (1999).
P. Antony, S. Bandyopadhyay, and S. K. De, "Synergism in properties of ionomeric polyblends based on zinc salts of carboxylated nitrile rubber and poly(ethylene-co-acrylic acid)", Polymer, 41, 787 (2000).
P. Antony, S. Bandyopadhyay, and S. K. De, "Thermoplastic elastomers based on ionomeric polyblends of zinc salts of poly(propylene-co-acrylic acid) and carboxylated nitrile rubber", J. Mater. Sci., 34, 2553 (1999).
P. Antony and S. K. De, "Ionomeric polyblends of zinc salts of maleated EPDM rubber and poly(ethylene-co-acrylic acid). I. Effect of blend ratio", J. Appl. Polym. Sci., 71, 1247 (1999).
Antony, P. and De, S.K. Synergism in properties of ionomeric polyblends based on zinc salt of maleated high density polyethylene and carboxylated nitrile rubber. J. Appl. Polym. Sci., 70, 483 (1998).
T. T. M. Phan, A. J. Denicola Jr, and L.S. Schadler, "Effect of addition of polyoxy propylenediamine on the morphology and mechanical properties of maleated polypropylene/maleated rubber blends", J. Appl. Polym. Sci., 68, 1451 (1998).
K. Chino, M. Ashiura, and J. Natori, "Thermoreversible crosslinking rubber using supramolecular hydrogen bonding networks", Rubb. Chem. Technol., 75, 713 (2002).
C. X. Sun, M.A.J. van der Mee, J.G.P. Goossens, and M. van Duin, "Thermoreversible cross-linking of maleated ethylene/ propylene copolymers using hydrogen-bonding and ionic interactions", Macromolecules, 39, 3441 (2006).
Y.-W. Chang, J. K. Mishra, S. K. Kim, and D. K. Kim, "Effect of supramolecular hydrogen bonded network on the properties of maleated ethylene propylene diene rubber/maleated high density polyethylene blend based thermoplastic elastomer", Mater. Lett., 60, 3118 (2006).
J. K. Mishra, Y.-W. Chang, D. K. Kim, and P. L. Nayak, "Heat shrinkable behavior of supramolecular hydrogen bonded maleated ethylene propylene diene rubber/ maleated high density polyethylene blend", Polym. Plast. Technol. Eng., 46: 585 (2007).
※ AI-Helper는 부적절한 답변을 할 수 있습니다.