본 논문은 30ton급 액체로켓엔진 연소기의 연소시험 검증용 제작에 관한 것이다. 기본설계와 상세설계를 통해 도면을 작성하고, 이에 따라 제작하였다. 연소기는 크게 헤드부와 챔버부로 구성되며, 챔버는 KSR-III에 적용되었던 내열재 챔버와 재생 냉각 방식의 챔버를 제작하였다. 연소기 헤드는 저온 특성이 좋은 SUS316L 재료를 사용하였다. 내열재 챔버는 내부는 silica/phenolic 재료를 사용하였고, 외부케이스는 SUS316L을 적용하였고, 재생 냉각 챔버는 C18200과 SUS316L 재료를 사용하였다. 선반 가공, 일반 밀링 가공, MCT 가공등의 기계적 가공을 한 후 전해 연마를 통해 이물질을 제거 하였다. 분사기와 분사기 플레이트의 접합과 재생 냉각 챔버 등 일부 부품의 접합은 구조적인 특성으로 인해 브레이징 기법을 적용하였다.
본 논문은 30ton급 액체로켓엔진 연소기의 연소시험 검증용 제작에 관한 것이다. 기본설계와 상세설계를 통해 도면을 작성하고, 이에 따라 제작하였다. 연소기는 크게 헤드부와 챔버부로 구성되며, 챔버는 KSR-III에 적용되었던 내열재 챔버와 재생 냉각 방식의 챔버를 제작하였다. 연소기 헤드는 저온 특성이 좋은 SUS316L 재료를 사용하였다. 내열재 챔버는 내부는 silica/phenolic 재료를 사용하였고, 외부케이스는 SUS316L을 적용하였고, 재생 냉각 챔버는 C18200과 SUS316L 재료를 사용하였다. 선반 가공, 일반 밀링 가공, MCT 가공등의 기계적 가공을 한 후 전해 연마를 통해 이물질을 제거 하였다. 분사기와 분사기 플레이트의 접합과 재생 냉각 챔버 등 일부 부품의 접합은 구조적인 특성으로 인해 브레이징 기법을 적용하였다.
This paper presents a fabrication of a full-stale combustion chamber of a liquid rocket engine for a ground hot firing test. Engine drawings for manufacturing were prepared after conceptual and detail designs. The combustor is composed of a head and a chamber. SUS316L is used for materials of the he...
This paper presents a fabrication of a full-stale combustion chamber of a liquid rocket engine for a ground hot firing test. Engine drawings for manufacturing were prepared after conceptual and detail designs. The combustor is composed of a head and a chamber. SUS316L is used for materials of the head because of the good quality in low temperature. Inner materials of the ablative cooling chamber is silica/phenolic and outer case materials is the SUS316L. Materials of the regenerative cooling chamber are C18200 and SUS316L. After lathe, general milling and MCT machinings, components were finished by electrolytic polishing. A brazing method was applied for bonding the injectors and the injector plate, the regenerative cooling chamber because of structure configurations.
This paper presents a fabrication of a full-stale combustion chamber of a liquid rocket engine for a ground hot firing test. Engine drawings for manufacturing were prepared after conceptual and detail designs. The combustor is composed of a head and a chamber. SUS316L is used for materials of the head because of the good quality in low temperature. Inner materials of the ablative cooling chamber is silica/phenolic and outer case materials is the SUS316L. Materials of the regenerative cooling chamber are C18200 and SUS316L. After lathe, general milling and MCT machinings, components were finished by electrolytic polishing. A brazing method was applied for bonding the injectors and the injector plate, the regenerative cooling chamber because of structure configurations.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.