共同住宅 에어컨 실외기 設置에따른 騷音ㆍ振動 저감에 관한 硏究 A Study on Reduction of Noise and Vibration owing to Establishing the Air Conditioner Outdoor Device in Tenement House원문보기
국내에서는 그동안 공동주택 시공시 기후특성상 냉방기가 짧기 때문에 설계시 냉방시스템이 배제되었으나 근래에 국민생활수준의 향상과 이상기후현상인 온난화 현상으로 인해 쾌적한 생활환경에 대한 욕구가 증대되면서 냉방설비 적용이 점차 증가하고 있는 실정이다. 이에 각 관련업계에서는 여러 가지 냉방시스템이 검토되고 있다. 그중에서 경제성 및 시공성, 유지관리 면에서 유리한 개별에어컨 시스템 적용이 현실화 되어가고 있다. 그러나 개별에어컨 설치에 따른 공동주택에서의 소음진동문제를 배제하기란 어렵다고 판단된다 따라서 소음진동발생의 주요요소를 설계 시공 단계에서 저감시킬 수 있는 방안을 측정대상아파트에서 실험을 통해 다음과 같이 제시하였다. (1) 공동주택 각평형별 적정 실외기 위치는 34평형, 62평형 모두 뒷발코니 외부 “C" TYPE이 적정한 것으로 분석되었다. (2) 적정 방진재와 흡음재두께는 고무패드와 25T가 적정한 것으로 평가되었다. (3) 공동주택에서 에어컨의 주요 진동, 소음원으로는 실외기뿐만 아니라 실내기도 동시에 작용하고 있음을 확인하였다. (4) 실험을 통해 측정데이터를 분석한 결과 바닥 최종 마감재의 특성에 따라 진동전파가 달라지는 것을 확인하였으며 이에 대한 연구가 필요하다고 사료된다. (5) 34평형의 경우처럼 바닥마감재가 비닐계 장판지일 경우 실내기 바닥에 ...
국내에서는 그동안 공동주택 시공시 기후특성상 냉방기가 짧기 때문에 설계시 냉방시스템이 배제되었으나 근래에 국민생활수준의 향상과 이상기후현상인 온난화 현상으로 인해 쾌적한 생활환경에 대한 욕구가 증대되면서 냉방설비 적용이 점차 증가하고 있는 실정이다. 이에 각 관련업계에서는 여러 가지 냉방시스템이 검토되고 있다. 그중에서 경제성 및 시공성, 유지관리 면에서 유리한 개별에어컨 시스템 적용이 현실화 되어가고 있다. 그러나 개별에어컨 설치에 따른 공동주택에서의 소음진동문제를 배제하기란 어렵다고 판단된다 따라서 소음진동발생의 주요요소를 설계 시공 단계에서 저감시킬 수 있는 방안을 측정대상아파트에서 실험을 통해 다음과 같이 제시하였다. (1) 공동주택 각평형별 적정 실외기 위치는 34평형, 62평형 모두 뒷발코니 외부 “C" TYPE이 적정한 것으로 분석되었다. (2) 적정 방진재와 흡음재두께는 고무패드와 25T가 적정한 것으로 평가되었다. (3) 공동주택에서 에어컨의 주요 진동, 소음원으로는 실외기뿐만 아니라 실내기도 동시에 작용하고 있음을 확인하였다. (4) 실험을 통해 측정데이터를 분석한 결과 바닥 최종 마감재의 특성에 따라 진동전파가 달라지는 것을 확인하였으며 이에 대한 연구가 필요하다고 사료된다. (5) 34평형의 경우처럼 바닥마감재가 비닐계 장판지일 경우 실내기 바닥에 POLYURETHANE MAT를 설치하면 초기단계에서 비용이 덜들면서 진동감소 효과를 쉽게 볼 수 있는 방안을 제시하고 적용가능성을 확인할 수 있었다. (6) 공동주택은 주용도인 주침실과 거실이 전면에 배치되어 있어 뒷발코니 외부로 실외기를 설치할 수 있는 전용설치대를 콘크리트 슬라브로 설계시공하여 실외기를 설치하면 진동측면에서는 기초가 안정되어 62평형의 “A" TYPE과 같은 효과를 볼 수 있으며 소음측면에서는 벽에 의한 투과손실효과를 볼 수 있어 세대로 전달되는 소음, 진동을 현저히 저감시킬 수 있다. 이와함께 에어컨 설치시 시공의 편리성과 안전을 고려하여 전용 실외기실쪽 난간은 개방형으로 시공되어야 하며 미관을 고려 설치대 전면에 내구성재질의 루바를 설치 주거공간의 미관문제를 해결할 수 있다.
국내에서는 그동안 공동주택 시공시 기후특성상 냉방기가 짧기 때문에 설계시 냉방시스템이 배제되었으나 근래에 국민생활수준의 향상과 이상기후현상인 온난화 현상으로 인해 쾌적한 생활환경에 대한 욕구가 증대되면서 냉방설비 적용이 점차 증가하고 있는 실정이다. 이에 각 관련업계에서는 여러 가지 냉방시스템이 검토되고 있다. 그중에서 경제성 및 시공성, 유지관리 면에서 유리한 개별에어컨 시스템 적용이 현실화 되어가고 있다. 그러나 개별에어컨 설치에 따른 공동주택에서의 소음진동문제를 배제하기란 어렵다고 판단된다 따라서 소음진동발생의 주요요소를 설계 시공 단계에서 저감시킬 수 있는 방안을 측정대상아파트에서 실험을 통해 다음과 같이 제시하였다. (1) 공동주택 각평형별 적정 실외기 위치는 34평형, 62평형 모두 뒷발코니 외부 “C" TYPE이 적정한 것으로 분석되었다. (2) 적정 방진재와 흡음재두께는 고무패드와 25T가 적정한 것으로 평가되었다. (3) 공동주택에서 에어컨의 주요 진동, 소음원으로는 실외기뿐만 아니라 실내기도 동시에 작용하고 있음을 확인하였다. (4) 실험을 통해 측정데이터를 분석한 결과 바닥 최종 마감재의 특성에 따라 진동전파가 달라지는 것을 확인하였으며 이에 대한 연구가 필요하다고 사료된다. (5) 34평형의 경우처럼 바닥마감재가 비닐계 장판지일 경우 실내기 바닥에 POLYURETHANE MAT를 설치하면 초기단계에서 비용이 덜들면서 진동감소 효과를 쉽게 볼 수 있는 방안을 제시하고 적용가능성을 확인할 수 있었다. (6) 공동주택은 주용도인 주침실과 거실이 전면에 배치되어 있어 뒷발코니 외부로 실외기를 설치할 수 있는 전용설치대를 콘크리트 슬라브로 설계시공하여 실외기를 설치하면 진동측면에서는 기초가 안정되어 62평형의 “A" TYPE과 같은 효과를 볼 수 있으며 소음측면에서는 벽에 의한 투과손실효과를 볼 수 있어 세대로 전달되는 소음, 진동을 현저히 저감시킬 수 있다. 이와함께 에어컨 설치시 시공의 편리성과 안전을 고려하여 전용 실외기실쪽 난간은 개방형으로 시공되어야 하며 미관을 고려 설치대 전면에 내구성재질의 루바를 설치 주거공간의 미관문제를 해결할 수 있다.
When operating the construction of the tenement house in domestic areas, because the time when air conditioner can be operated is short owing to the characteristics of the local climate, when the drafting work was conducted, the air conditioner system was excluded, but in recent days the improvement...
When operating the construction of the tenement house in domestic areas, because the time when air conditioner can be operated is short owing to the characteristics of the local climate, when the drafting work was conducted, the air conditioner system was excluded, but in recent days the improvement of the national quality of life and the warm weather which is the phenomena of the extraordinary weather phenomena increased the desire for the comfortable environment for life, and consequently, recently the usage of devices related with the air conditioner were increased. Thus the related industrial companies are researching various air conditioning systems. Among those air conditioners, the individual air conditioner system application, which is beneficial for the economical aspect, the convenience for construction, and maintenance-administration point, was being realized. However, it is thought that the problem of noise and vibration owing to the establishment of the individual air conditioner in tenement house could not be excluded. Consequently, the way, which enable the main elements of the noise and vibration occurrence to be reduced in the drawing and drafting level, was experimented and then proposed as follows. 1. It is analyzed that the proper position for the outdoor air conditioner device in each size of the tenement house was the outside "C" type in both 34 pyung type, and 62 pyung type. 2. It is evaluated that the adequate thickness of the dustproof materials and the noiseproof should be used by the rubber pad and 25T. 3. When establishing the package air conditioner in the tenement house, as the main vibration and noise element, the fact that the indoor device as well as the outdoor device affect them was confirmed. 4. The result, which analyzed the estimated data through the experiment, enable to confirm that according to the features of the last bottom closing material, the vibration wave changed, and it is thought that the study for those should be researched. 5. As the case of 34 pyung which used the vinyl papered floor as the last bottom closing material, if the polyurethane mat is established in the bottom of the indoor device, it could be proposed the way that the process could easily reduce the initial cost, and reduce the vibration, and the applied possibility could be confirmed. 6. When the bedroom and living room, which are the mainly used rooms of the tenement house level, are located in front of the area, the exclusive shelf, which is drawn and made up of the concrete slave, for establishing which enables the outdoor device to be established in outside of the back balcony, and thus if the outdoor device could be established, in the case of the vibration, the base became stable, consequently those process enables to make the same effects with the "A" type of the 62 pyung type, and in the case of the noise, the transmission-reduction effects could be occurred by the wall and consequently the noise and vibration could be considerably reduced.
When operating the construction of the tenement house in domestic areas, because the time when air conditioner can be operated is short owing to the characteristics of the local climate, when the drafting work was conducted, the air conditioner system was excluded, but in recent days the improvement of the national quality of life and the warm weather which is the phenomena of the extraordinary weather phenomena increased the desire for the comfortable environment for life, and consequently, recently the usage of devices related with the air conditioner were increased. Thus the related industrial companies are researching various air conditioning systems. Among those air conditioners, the individual air conditioner system application, which is beneficial for the economical aspect, the convenience for construction, and maintenance-administration point, was being realized. However, it is thought that the problem of noise and vibration owing to the establishment of the individual air conditioner in tenement house could not be excluded. Consequently, the way, which enable the main elements of the noise and vibration occurrence to be reduced in the drawing and drafting level, was experimented and then proposed as follows. 1. It is analyzed that the proper position for the outdoor air conditioner device in each size of the tenement house was the outside "C" type in both 34 pyung type, and 62 pyung type. 2. It is evaluated that the adequate thickness of the dustproof materials and the noiseproof should be used by the rubber pad and 25T. 3. When establishing the package air conditioner in the tenement house, as the main vibration and noise element, the fact that the indoor device as well as the outdoor device affect them was confirmed. 4. The result, which analyzed the estimated data through the experiment, enable to confirm that according to the features of the last bottom closing material, the vibration wave changed, and it is thought that the study for those should be researched. 5. As the case of 34 pyung which used the vinyl papered floor as the last bottom closing material, if the polyurethane mat is established in the bottom of the indoor device, it could be proposed the way that the process could easily reduce the initial cost, and reduce the vibration, and the applied possibility could be confirmed. 6. When the bedroom and living room, which are the mainly used rooms of the tenement house level, are located in front of the area, the exclusive shelf, which is drawn and made up of the concrete slave, for establishing which enables the outdoor device to be established in outside of the back balcony, and thus if the outdoor device could be established, in the case of the vibration, the base became stable, consequently those process enables to make the same effects with the "A" type of the 62 pyung type, and in the case of the noise, the transmission-reduction effects could be occurred by the wall and consequently the noise and vibration could be considerably reduced.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.