Polyorganosiloxane (PSX)과 α,ω-isocyanated polyurethaneprepolymer (PU)를 무게비 10:0, 8:2, 7:3, 6:4 및 5:5로 반응시켜 얻은 silicone 변성 polyurethane (TUMPS)과 여기에 각종 첨가제와 filler를 첨가하여 제조한 TUMPS sealant의 경화속도 및 접착특성을 측정하였다. PU와 PSX의 중량비를 8:2와 7:3으로 하여 제조한 TUMPS및 TUMPS sealant의 접착 신장율이 약 480∼482%로 아주 우수하였으며 접착 최대하중은 TUMPS가 약 50 kgf이고 TUMPS sealant는 약 60 kgf이었다. DSC를 이용하여 경화속도를 측정하기 위해 ...
Polyorganosiloxane (PSX)과 α,ω-isocyanated polyurethaneprepolymer (PU)를 무게비 10:0, 8:2, 7:3, 6:4 및 5:5로 반응시켜 얻은 silicone 변성 polyurethane (TUMPS)과 여기에 각종 첨가제와 filler를 첨가하여 제조한 TUMPS sealant의 경화속도 및 접착특성을 측정하였다. PU와 PSX의 중량비를 8:2와 7:3으로 하여 제조한 TUMPS및 TUMPS sealant의 접착 신장율이 약 480∼482%로 아주 우수하였으며 접착 최대하중은 TUMPS가 약 50 kgf이고 TUMPS sealant는 약 60 kgf이었다. DSC를 이용하여 경화속도를 측정하기 위해 미분법으로 Kissinger 방법과 적분법으로 Ozawa 방법으로 활성화에너지를 측정하였다. PU와 PSX의 중량비를 7:3으로 하여 제조한 TUMPS 및 TUMPS sealant에 대해 Kissinger 방법으로 측정한 경화 활성화에너지는 46.60과 31.69, 32.62 KJ/mol이 었다. TGA 이용하여 경화속도를 측정하기위해 미분법으로 Kissinger, Friedman 방법과 적분법으로 Ozawa, Coats-Redfern 방법으로 경화 활성화에너지를 측정하였다. PU:PSX의 중랴비를 7:3으로 하여 제조한 TUMPS에 대해 경화 활성화에너지는 Kissinger, Fredman, Ozawa 및 Coats-Redfern 방법으로 측정한 결과 5.26, 7.61, 0.65 및 23.69 KJ/mol로 PU 탄성체나 sealant보다 경화 활성화에너지가 아주 낮았다. TUMPS 및 TUMPS sealant를 석고 각봉에 부착시킬 경우 20초 이상으로 대부분의 시료가 부착되어 우수하였으나 PU:PSX의 중량비를 5:5로하여 제조한 TUMPS 탄성체가 9 초로 낮은 것으로 측정되으며, 경화도는 중량비를 7:3으로 하여 제조한 TUMPS 및 TUMPS sealant가 95.9, 99.6 %로 우수하였고, 균열은 TUMPS sealant와 석고 각봉과의 사이에서 박리, 분해가 되지 않았다. 또한, 저온저장의 경우 액체질소 안에서도 안전하여 저온저장성이 우수하였으며, 겉경화속도는 TUMPS는 265∼298 min으로 PU보다 빠른 겉경화속도를 나타내었고 TUMPS sealant는 39∼43 min으로 매우 빠르게 겉경화가 일어났다. 80 ℃에서의 가열감량은 TUMPS가 약 1∼2 %, 그리고 TUMPS sealant는 4∼ 4.3%였다.
Polyorganosiloxane (PSX)과 α,ω-isocyanated polyurethane prepolymer (PU)를 무게비 10:0, 8:2, 7:3, 6:4 및 5:5로 반응시켜 얻은 silicone 변성 polyurethane (TUMPS)과 여기에 각종 첨가제와 filler를 첨가하여 제조한 TUMPS sealant의 경화속도 및 접착특성을 측정하였다. PU와 PSX의 중량비를 8:2와 7:3으로 하여 제조한 TUMPS및 TUMPS sealant의 접착 신장율이 약 480∼482%로 아주 우수하였으며 접착 최대하중은 TUMPS가 약 50 kgf이고 TUMPS sealant는 약 60 kgf이었다. DSC를 이용하여 경화속도를 측정하기 위해 미분법으로 Kissinger 방법과 적분법으로 Ozawa 방법으로 활성화에너지를 측정하였다. PU와 PSX의 중량비를 7:3으로 하여 제조한 TUMPS 및 TUMPS sealant에 대해 Kissinger 방법으로 측정한 경화 활성화에너지는 46.60과 31.69, 32.62 KJ/mol이 었다. TGA 이용하여 경화속도를 측정하기위해 미분법으로 Kissinger, Friedman 방법과 적분법으로 Ozawa, Coats-Redfern 방법으로 경화 활성화에너지를 측정하였다. PU:PSX의 중랴비를 7:3으로 하여 제조한 TUMPS에 대해 경화 활성화에너지는 Kissinger, Fredman, Ozawa 및 Coats-Redfern 방법으로 측정한 결과 5.26, 7.61, 0.65 및 23.69 KJ/mol로 PU 탄성체나 sealant보다 경화 활성화에너지가 아주 낮았다. TUMPS 및 TUMPS sealant를 석고 각봉에 부착시킬 경우 20초 이상으로 대부분의 시료가 부착되어 우수하였으나 PU:PSX의 중량비를 5:5로하여 제조한 TUMPS 탄성체가 9 초로 낮은 것으로 측정되으며, 경화도는 중량비를 7:3으로 하여 제조한 TUMPS 및 TUMPS sealant가 95.9, 99.6 %로 우수하였고, 균열은 TUMPS sealant와 석고 각봉과의 사이에서 박리, 분해가 되지 않았다. 또한, 저온저장의 경우 액체질소 안에서도 안전하여 저온저장성이 우수하였으며, 겉경화속도는 TUMPS는 265∼298 min으로 PU보다 빠른 겉경화속도를 나타내었고 TUMPS sealant는 39∼43 min으로 매우 빠르게 겉경화가 일어났다. 80 ℃에서의 가열감량은 TUMPS가 약 1∼2 %, 그리고 TUMPS sealant는 4∼ 4.3%였다.
Polyurethane modified with polyorganosiloxne (TUMPS) was prepared by adding polyorganosiloxane (PSX) to polyurethane (PU) at the ratio of 10 to 0, 8:2, 7:3, 6:4 and 5:5, respectively. And also, TUMPS sealant was prepared by adding various additives, such as plasticizer, crosslinking agent, and visco...
Polyurethane modified with polyorganosiloxne (TUMPS) was prepared by adding polyorganosiloxane (PSX) to polyurethane (PU) at the ratio of 10 to 0, 8:2, 7:3, 6:4 and 5:5, respectively. And also, TUMPS sealant was prepared by adding various additives, such as plasticizer, crosslinking agent, and viscosity increasing agent to TUMPS elastomer at room temperature under nitrogen atmosphere. And also, TUMPS sealant by adding the PSX to PU mixed. Adhesion, elongation and load properties for TUMPS and TUMPS sealant contained 20 and 30 wt % of PSX for PU were better than those TUMPS and TUMPS sealant containet 0, 40 and 50 weight % of PSX for PU. Cure kinetics and activation energy of TUMPS and TUMPS sealant were studied by dynamic DSC and dynamic TGA analysis. From the results of DSC and TGA, activation energy of TUMPSand TUMPS sealant contained 30 weight % of PSX for PR were more decreased compared than those of the others. It was difficult to distinguish original cure peaks from another exothermic peak due to various fillers. The degree of cure for TUMPS and TUMPS sealant (7:3) showd 95.9 and 99.6 %. And, skin over time were about 265∼298 and 39∼43 min. Adhesive force showed good characteristics and maintained for 14 days. Weatherability was measured by adding TUMPS and TUMPS sealant to liquid nitrogen for 6 h and showed cleavge nd crack. And also, TUMPS and TUMPS sealant was remained in vacuum oven at 80 ℃ for 7days and then, did not show excessive decrease in weight.
Polyurethane modified with polyorganosiloxne (TUMPS) was prepared by adding polyorganosiloxane (PSX) to polyurethane (PU) at the ratio of 10 to 0, 8:2, 7:3, 6:4 and 5:5, respectively. And also, TUMPS sealant was prepared by adding various additives, such as plasticizer, crosslinking agent, and viscosity increasing agent to TUMPS elastomer at room temperature under nitrogen atmosphere. And also, TUMPS sealant by adding the PSX to PU mixed. Adhesion, elongation and load properties for TUMPS and TUMPS sealant contained 20 and 30 wt % of PSX for PU were better than those TUMPS and TUMPS sealant containet 0, 40 and 50 weight % of PSX for PU. Cure kinetics and activation energy of TUMPS and TUMPS sealant were studied by dynamic DSC and dynamic TGA analysis. From the results of DSC and TGA, activation energy of TUMPSand TUMPS sealant contained 30 weight % of PSX for PR were more decreased compared than those of the others. It was difficult to distinguish original cure peaks from another exothermic peak due to various fillers. The degree of cure for TUMPS and TUMPS sealant (7:3) showd 95.9 and 99.6 %. And, skin over time were about 265∼298 and 39∼43 min. Adhesive force showed good characteristics and maintained for 14 days. Weatherability was measured by adding TUMPS and TUMPS sealant to liquid nitrogen for 6 h and showed cleavge nd crack. And also, TUMPS and TUMPS sealant was remained in vacuum oven at 80 ℃ for 7days and then, did not show excessive decrease in weight.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.