Ni,Cr,Mo를 첨가한 SNCM439 강종은 열간 환봉 가공과정 중에 표면결함으로 인하여 소재 생산성 및 수익성에 많은 악영향을 끼치고 있었다. 하지만 SNCM439 강종의 소재형상별,온도별,변형속도별, 균열시간별 다양한 열간가공성 시험을 통해서 1000℃온도 이하의 낮은 온도에서 변형속도가 빠를 경우 변형이 접힘 및 주름형태의 불안정한 변형거동을 보이는 것을 알 수 있었다. 그리고 시뮬레이션 과정을 통해서 연주빌렛 소재의 코너부에 특히 이러한 온도변화 및 변형속도가 큰 것을 관찰하고 이것을 개선하기 위해 ...
Ni,Cr,Mo를 첨가한 SNCM439 강종은 열간 환봉 가공과정 중에 표면결함으로 인하여 소재 생산성 및 수익성에 많은 악영향을 끼치고 있었다. 하지만 SNCM439 강종의 소재형상별,온도별,변형속도별, 균열시간별 다양한 열간가공성 시험을 통해서 1000℃온도 이하의 낮은 온도에서 변형속도가 빠를 경우 변형이 접힘 및 주름형태의 불안정한 변형거동을 보이는 것을 알 수 있었다. 그리고 시뮬레이션 과정을 통해서 연주빌렛 소재의 코너부에 특히 이러한 온도변화 및 변형속도가 큰 것을 관찰하고 이것을 개선하기 위해 가열온도 확보 및 코너부 Radius 증대를 통해서 결함 발생율을 저감시킬 수 있었다.
Ni,Cr,Mo를 첨가한 SNCM439 강종은 열간 환봉 가공과정 중에 표면결함으로 인하여 소재 생산성 및 수익성에 많은 악영향을 끼치고 있었다. 하지만 SNCM439 강종의 소재형상별,온도별,변형속도별, 균열시간별 다양한 열간가공성 시험을 통해서 1000℃온도 이하의 낮은 온도에서 변형속도가 빠를 경우 변형이 접힘 및 주름형태의 불안정한 변형거동을 보이는 것을 알 수 있었다. 그리고 시뮬레이션 과정을 통해서 연주빌렛 소재의 코너부에 특히 이러한 온도변화 및 변형속도가 큰 것을 관찰하고 이것을 개선하기 위해 가열온도 확보 및 코너부 Radius 증대를 통해서 결함 발생율을 저감시킬 수 있었다.
It is well-known that the SNCM 439 steel shows good formability at high temperature. However, the intermittant, discontinous defects are frequantly observed on the surface after bar rolling of SNCM 439 steel billet. The analysis for the defects shows that they might form during hot rolling. Therefor...
It is well-known that the SNCM 439 steel shows good formability at high temperature. However, the intermittant, discontinous defects are frequantly observed on the surface after bar rolling of SNCM 439 steel billet. The analysis for the defects shows that they might form during hot rolling. Therefore, the possibility of defect formation was examined through the simulation of the bar rolling of the square billet and the hot deformation test, The results shows that the defects might be formed due to plastic instability which occurs at the corner of the billet during bar rolling. The result was tried to be applied for the reduction of the defects. Actually the defects could be reduced by controlling the conditions which had influence on the plastic instability at the corner of billets.
It is well-known that the SNCM 439 steel shows good formability at high temperature. However, the intermittant, discontinous defects are frequantly observed on the surface after bar rolling of SNCM 439 steel billet. The analysis for the defects shows that they might form during hot rolling. Therefore, the possibility of defect formation was examined through the simulation of the bar rolling of the square billet and the hot deformation test, The results shows that the defects might be formed due to plastic instability which occurs at the corner of the billet during bar rolling. The result was tried to be applied for the reduction of the defects. Actually the defects could be reduced by controlling the conditions which had influence on the plastic instability at the corner of billets.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.