본 연구에서는 폴리론 화이버 혼입 공법을 적용한 고강도 콘크리트의 기둥, 보 및 슬래브 구조체의 기초적 특성 및 폭렬성상, 내부온도이력 등 내화성능을 분석하였는데 그 결과를 종합하면 다음과 같다. 1) 고강도 콘크리트의 기초적 특성으로, 플레인 콘크리트의 슬럼프플로우는 고유동 콘크리트 범위인 600±100을 나타냈고, 500 mm ...
본 연구에서는 폴리론 화이버 혼입 공법을 적용한 고강도 콘크리트의 기둥, 보 및 슬래브 구조체의 기초적 특성 및 폭렬성상, 내부온도이력 등 내화성능을 분석하였는데 그 결과를 종합하면 다음과 같다. 1) 고강도 콘크리트의 기초적 특성으로, 플레인 콘크리트의 슬럼프플로우는 고유동 콘크리트 범위인 600±100을 나타냈고, 500 mm 도달시간 역시 JSCE에서 규정한 1등급 범위를 만족하였으며, 압축강도는 88 MPa이상의 고강도 범위를 나타냈다. 2) 고강도 콘크리트 기둥 구조체의 내화특성으로 폴리론 화이버를 혼입하지 않은 플레인의 경우 3시간 내화 후 급격한 온도상승과 높은 온도에 의한 내부 수증기압의 증대로 심한 파괴 폭렬이 발생하여 철근이 노출되었고, 폴리론 화이버를 혼입한 경우 일부 표면 박리 현상은 발생하였으나 비교적 양호한 내화성능을 나타내었다. 3) 고강도 콘크리트 기둥의 단면 크기 변화에 따른 내화특성으로 구조체의 단면이 커질수록 폭렬 현상이 발생하여 폭렬 면적이 증가하는 것으로 나타났으나 3시간 내화 후 모두 국토해양부에서 규정한 최고온도 및 평균온도에 미치지 않는 것으로 나타났다. 또한 본 연구범위에서는 부재 단면 크기가 700×700 mm 정도의 경우 부재의 평균온도 변화가 크지 않고, 최고온도 역시 국토해양부 규정을 만족 하였으며 폭렬현상도 심하지 않은 것으로 나타났다. 4) 고강도 콘크리트 보·슬래브 구조체의 내화특성으로 먼저 슬래브의 경우 급심한 고온에 노출되면서 슬래브 중앙에 폭렬 현상이 발생하였고, 보의 경우 내화시험 10분 전후로 박리 폭렬이 발생 하였으나, 3시간 내화 후 최고온도는 581 ℃로 내화인증 규정의 최고온도 649 ℃에는 미치지 않는 것으로 나타났고, 표면 및 모서리 부분의 경우 다소 높은 온도 범위를 나타내었지만 모두 내화 인증 규정에는 만족하는 것으로 나타났다. 이상을 종합하면, 고강도 콘크리트의 기둥, 보 구조체의 경우 일부 표면에서 박리 현상이 발생하였으나 국토해양부에서 규정한 최고온도 및 평균온도 범위를 만족하는 것으로 나타나 고강도 콘크리트를 사용한 기둥 및 보 구조체의 내화성능 확보를 위한 공법으로 폴리론 화이버 공법을 적용 하여 활용하는 것이 효과적일 것으로 판단된다.
본 연구에서는 폴리론 화이버 혼입 공법을 적용한 고강도 콘크리트의 기둥, 보 및 슬래브 구조체의 기초적 특성 및 폭렬성상, 내부온도이력 등 내화성능을 분석하였는데 그 결과를 종합하면 다음과 같다. 1) 고강도 콘크리트의 기초적 특성으로, 플레인 콘크리트의 슬럼프플로우는 고유동 콘크리트 범위인 600±100을 나타냈고, 500 mm 도달시간 역시 JSCE에서 규정한 1등급 범위를 만족하였으며, 압축강도는 88 MPa이상의 고강도 범위를 나타냈다. 2) 고강도 콘크리트 기둥 구조체의 내화특성으로 폴리론 화이버를 혼입하지 않은 플레인의 경우 3시간 내화 후 급격한 온도상승과 높은 온도에 의한 내부 수증기압의 증대로 심한 파괴 폭렬이 발생하여 철근이 노출되었고, 폴리론 화이버를 혼입한 경우 일부 표면 박리 현상은 발생하였으나 비교적 양호한 내화성능을 나타내었다. 3) 고강도 콘크리트 기둥의 단면 크기 변화에 따른 내화특성으로 구조체의 단면이 커질수록 폭렬 현상이 발생하여 폭렬 면적이 증가하는 것으로 나타났으나 3시간 내화 후 모두 국토해양부에서 규정한 최고온도 및 평균온도에 미치지 않는 것으로 나타났다. 또한 본 연구범위에서는 부재 단면 크기가 700×700 mm 정도의 경우 부재의 평균온도 변화가 크지 않고, 최고온도 역시 국토해양부 규정을 만족 하였으며 폭렬현상도 심하지 않은 것으로 나타났다. 4) 고강도 콘크리트 보·슬래브 구조체의 내화특성으로 먼저 슬래브의 경우 급심한 고온에 노출되면서 슬래브 중앙에 폭렬 현상이 발생하였고, 보의 경우 내화시험 10분 전후로 박리 폭렬이 발생 하였으나, 3시간 내화 후 최고온도는 581 ℃로 내화인증 규정의 최고온도 649 ℃에는 미치지 않는 것으로 나타났고, 표면 및 모서리 부분의 경우 다소 높은 온도 범위를 나타내었지만 모두 내화 인증 규정에는 만족하는 것으로 나타났다. 이상을 종합하면, 고강도 콘크리트의 기둥, 보 구조체의 경우 일부 표면에서 박리 현상이 발생하였으나 국토해양부에서 규정한 최고온도 및 평균온도 범위를 만족하는 것으로 나타나 고강도 콘크리트를 사용한 기둥 및 보 구조체의 내화성능 확보를 위한 공법으로 폴리론 화이버 공법을 적용 하여 활용하는 것이 효과적일 것으로 판단된다.
This study analyzed the fire resistance performances of high strength concrete applied with polyron fiber mixing method like the basic characteristics, spalling shape and internal temperature history etc of columns, beams and slab structure, and the analysis results can be summed up as follows 1) Am...
This study analyzed the fire resistance performances of high strength concrete applied with polyron fiber mixing method like the basic characteristics, spalling shape and internal temperature history etc of columns, beams and slab structure, and the analysis results can be summed up as follows 1) Among the basic characteristics of high strength concrete, the slump flow of plain concrete was shown to be 600±100, the range of high flow concrete, where 500mm arrival time also satisfied 1st class range specified by JSCE, and compressive strength showed high strength range of 88MPa. 2) Among the fire resistance characteristics of high strength concrete column structure, plain structure with no mixture of polyron fiber showed severe failure spalling, resulting in exposure of reinforcement due to increase of inside vapor pressure by sudden temperature rise 3 hours after fire resistance test, and in the case of polyron fiber mixture, partial surface peeling occurred, but fire resistance performance was relatively good. 3) As for the fire resistance characteristics by the high strength concrete column cross section size change, the wider the cross section of structure is, the more frequently spalling occurred, giving rise to increase of spalling area, however 3 hours after fire resistance test, all were below the highest temperature and average temperature specified by MLTM. In addition, in case of member cross section of 700x700mm or so, member average temperature change was not significant, where highest temperature also satisfied MLTM regulation, and spalling also was not severe. 4) As for the fire resistance characteristics of high strength concrete beam and slab structure, slab experienced spalling in the center as it gets exposed severely to high temperature, and with beam, peeling spalling occurred 10 minutes before and after fire resistance test, but 3 hours after fire resistance test, highest temperature, 581℃, was not up to 649℃, the highest temperature specified for fire resistance certification. Surface and corner portions showed more or less high temperature range but were shown to satisfy fire resistance certification rule in all. In conclusion, in the case of high strength concrete column and beam structure, peeling occurred on part of the surface, but the highest temperature and average temperature range specified by MLTM were satisfied, so it was determined that polyron fiber method would be effective to be utilized as the construction method of gaining the fire resistance performance of column and beam structure using high strength concrete.
This study analyzed the fire resistance performances of high strength concrete applied with polyron fiber mixing method like the basic characteristics, spalling shape and internal temperature history etc of columns, beams and slab structure, and the analysis results can be summed up as follows 1) Among the basic characteristics of high strength concrete, the slump flow of plain concrete was shown to be 600±100, the range of high flow concrete, where 500mm arrival time also satisfied 1st class range specified by JSCE, and compressive strength showed high strength range of 88MPa. 2) Among the fire resistance characteristics of high strength concrete column structure, plain structure with no mixture of polyron fiber showed severe failure spalling, resulting in exposure of reinforcement due to increase of inside vapor pressure by sudden temperature rise 3 hours after fire resistance test, and in the case of polyron fiber mixture, partial surface peeling occurred, but fire resistance performance was relatively good. 3) As for the fire resistance characteristics by the high strength concrete column cross section size change, the wider the cross section of structure is, the more frequently spalling occurred, giving rise to increase of spalling area, however 3 hours after fire resistance test, all were below the highest temperature and average temperature specified by MLTM. In addition, in case of member cross section of 700x700mm or so, member average temperature change was not significant, where highest temperature also satisfied MLTM regulation, and spalling also was not severe. 4) As for the fire resistance characteristics of high strength concrete beam and slab structure, slab experienced spalling in the center as it gets exposed severely to high temperature, and with beam, peeling spalling occurred 10 minutes before and after fire resistance test, but 3 hours after fire resistance test, highest temperature, 581℃, was not up to 649℃, the highest temperature specified for fire resistance certification. Surface and corner portions showed more or less high temperature range but were shown to satisfy fire resistance certification rule in all. In conclusion, in the case of high strength concrete column and beam structure, peeling occurred on part of the surface, but the highest temperature and average temperature range specified by MLTM were satisfied, so it was determined that polyron fiber method would be effective to be utilized as the construction method of gaining the fire resistance performance of column and beam structure using high strength concrete.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.