단계 한시 거리계전 알고리즘은 보호 구간을 선택적으로 보호 할 수 있는 장점을 갖고 있기 때문에 후비보호용으로 주로 사용되며 송전계통에서는 송전선로 및 변압기의 단락, 지락보호용으로 사용되어진다. 다른 후비보호 계전기들과의 보호 협조를 위하여 보호 구간 및 동작 시간의 정정 방법이 미리 정해져 있으나 특정 조건 하에서는 다른 보호계전기와 보호구간이 중복되는 문제가 발생할 소지가 있다. 일반적으로 송전계통의 변압기들은 계통의 안정도를 위해 송전선로에 비해 큰 ...
단계 한시 거리계전 알고리즘은 보호 구간을 선택적으로 보호 할 수 있는 장점을 갖고 있기 때문에 후비보호용으로 주로 사용되며 송전계통에서는 송전선로 및 변압기의 단락, 지락보호용으로 사용되어진다. 다른 후비보호 계전기들과의 보호 협조를 위하여 보호 구간 및 동작 시간의 정정 방법이 미리 정해져 있으나 특정 조건 하에서는 다른 보호계전기와 보호구간이 중복되는 문제가 발생할 소지가 있다. 일반적으로 송전계통의 변압기들은 계통의 안정도를 위해 송전선로에 비해 큰 임피던스를 갖도록 설계되는데 이로 인해 변압기 보호용 거리계전기의 보호구간이 인접 선로의 보호계전기들의 보호구간과 겹칠 수 있다. 이런 문제를 해결하기 위해 IEEE Standard에서는 중복보호구간에서의 동작 시간의 변경을 통해 오동작을 방지하는 방법을 추천하고 있으며,[2] 국내에서는 계통 조건에 따라 동작 구간을 변경하여 중복 구간을 제거하는 방법을 사용하는 경우도 있다. 그러나 이 두 가지 방법 모두 문제를 근본적으로 제거하지 못하며 상황에 따라선 또 다른 문제를 일으킬 소지가 있으므로 중복 보호구간을 해결하기 위한 완벽한 대책으로 보기는 어렵다.
본 논문에서는 변압기 보호용 거리계전기와 인접 선로의 보호계전기들의 보호 협조 문제를 해결하기 위해 IEC 61850 기반의 변전소에서 통신을 이용한 개선된 보호 협조방법을 제안하였다. 또한 제안된 알고리즘을 검증하기 위해 IEC 61850 기반의 IED (Intelligent Electronic Device)와 커널 2.6 LINUX 기반의 네트워크 시스템을 구성하였으며 실제 통신시간을 측정하여 시스템의 신뢰성을 입증하였다. 고장 데이터 취득을 위한 송전급 변압기가 포함된 변전소 시스템을 PSCAD로 모델링하고 Mircosoft Visual C++ 6.0을 통하여 알고리즘을 구현하였다.
단계 한시 거리계전 알고리즘은 보호 구간을 선택적으로 보호 할 수 있는 장점을 갖고 있기 때문에 후비보호용으로 주로 사용되며 송전계통에서는 송전선로 및 변압기의 단락, 지락보호용으로 사용되어진다. 다른 후비보호 계전기들과의 보호 협조를 위하여 보호 구간 및 동작 시간의 정정 방법이 미리 정해져 있으나 특정 조건 하에서는 다른 보호계전기와 보호구간이 중복되는 문제가 발생할 소지가 있다. 일반적으로 송전계통의 변압기들은 계통의 안정도를 위해 송전선로에 비해 큰 임피던스를 갖도록 설계되는데 이로 인해 변압기 보호용 거리계전기의 보호구간이 인접 선로의 보호계전기들의 보호구간과 겹칠 수 있다. 이런 문제를 해결하기 위해 IEEE Standard에서는 중복보호구간에서의 동작 시간의 변경을 통해 오동작을 방지하는 방법을 추천하고 있으며,[2] 국내에서는 계통 조건에 따라 동작 구간을 변경하여 중복 구간을 제거하는 방법을 사용하는 경우도 있다. 그러나 이 두 가지 방법 모두 문제를 근본적으로 제거하지 못하며 상황에 따라선 또 다른 문제를 일으킬 소지가 있으므로 중복 보호구간을 해결하기 위한 완벽한 대책으로 보기는 어렵다.
본 논문에서는 변압기 보호용 거리계전기와 인접 선로의 보호계전기들의 보호 협조 문제를 해결하기 위해 IEC 61850 기반의 변전소에서 통신을 이용한 개선된 보호 협조방법을 제안하였다. 또한 제안된 알고리즘을 검증하기 위해 IEC 61850 기반의 IED (Intelligent Electronic Device)와 커널 2.6 LINUX 기반의 네트워크 시스템을 구성하였으며 실제 통신시간을 측정하여 시스템의 신뢰성을 입증하였다. 고장 데이터 취득을 위한 송전급 변압기가 포함된 변전소 시스템을 PSCAD로 모델링하고 Mircosoft Visual C++ 6.0을 통하여 알고리즘을 구현하였다.
A distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for time differential and regions. According to conventional step distance protection scheme, Zone 2 can exceed the ordinary coverage excessively in case of a trans...
A distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for time differential and regions. According to conventional step distance protection scheme, Zone 2 can exceed the ordinary coverage excessively in case of a transformer protection relay. In this case, there can be overlapped protection area from the backup protection relays, and malfunctions can be occurred when any fault occurs in the overlapped protection area. Distance relays and overcurrent relays are used for backup protection generally, and both relays have this problem, the malfunction from the overlapped protection area. Corresponding to IEEE standard, this problem is coped with a modification of a operation time. In Korea, zones are modified to cope with this problem in some specific condition. These two methods may not be obvious to handle this problem because these methods, modifying the common rule, can cause another coordination problem. To overcome this problem clearly, this paper describes an improved backup protection coordination scheme using an IEC 61850-based distance relay for transformer backup protection. IEC 61850-based IED(Intelligent Electronic Device) and network system based on the kernel 2.6 LINUX are realized to verify the proposed method. And a method to estimate the communication time shows that the proposed coordination method is reliable.
A distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for time differential and regions. According to conventional step distance protection scheme, Zone 2 can exceed the ordinary coverage excessively in case of a transformer protection relay. In this case, there can be overlapped protection area from the backup protection relays, and malfunctions can be occurred when any fault occurs in the overlapped protection area. Distance relays and overcurrent relays are used for backup protection generally, and both relays have this problem, the malfunction from the overlapped protection area. Corresponding to IEEE standard, this problem is coped with a modification of a operation time. In Korea, zones are modified to cope with this problem in some specific condition. These two methods may not be obvious to handle this problem because these methods, modifying the common rule, can cause another coordination problem. To overcome this problem clearly, this paper describes an improved backup protection coordination scheme using an IEC 61850-based distance relay for transformer backup protection. IEC 61850-based IED(Intelligent Electronic Device) and network system based on the kernel 2.6 LINUX are realized to verify the proposed method. And a method to estimate the communication time shows that the proposed coordination method is reliable.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.