앞으로의 디스플레이 연구는 기존 디스플레이의 필요 요건이었던 경박단소(經薄短小)의 특성과 Flexible이 가능하고, 또한 PDLC 제작 공정의 차별화(Roll-to-Roll)를 통한 가격의 차별화를 가질 수 있는 방향으로 나아간다. 그러나 현재 PDLC의 단점으로는 디스플레이에서 사용되고 있는 TFT의 구동 범위 이상의 높은 전압을 통해 구동이 되고, 기존 디스플레이에 비해 낮은 Contrast Ratio 및 좁은 ...
앞으로의 디스플레이 연구는 기존 디스플레이의 필요 요건이었던 경박단소(經薄短小)의 특성과 Flexible이 가능하고, 또한 PDLC 제작 공정의 차별화(Roll-to-Roll)를 통한 가격의 차별화를 가질 수 있는 방향으로 나아간다. 그러나 현재 PDLC의 단점으로는 디스플레이에서 사용되고 있는 TFT의 구동 범위 이상의 높은 전압을 통해 구동이 되고, 기존 디스플레이에 비해 낮은 Contrast Ratio 및 좁은 시야각을 갖는 문제점을 안고 있다. 그러므로 이번 연구에서는 시야각 개선과 동시에 구동전압을 낮추기 위한 방편으로 강유전성 Nanoparticle을 이용하였다. 본 연구는 PDLC의 광학적 특성을 비교하기 위하여 액정은 BL001을 고분자로는 NOA65를 사용하여 6:4의 블렌딩 비율을 고정시키고 반응의 진행을 위하여 HMPP(2 - Hydroxy - 2 - methyl - propiophenone)를 첨가하여 모세관 현상을 이용한 방법으로 액정과 고분자를 Cleaned ITO Galss 주입하고 UV로 고분자를 경화시켜 Referenc Cell을 제작하였고 이때 Cell Gap은 20μm로 유지시켰다. 기존에 연구가 진행되었던 시야각 개선을 위한 Nanoparticle (Melamine formaldehyde, Sb2O5, TiO2)을 첨가한 PDLC와 구동전압과 시야각 개선을 동시에 실현시킬 수 있는 강유전성 Nanoparticle (SrTiO3, BaTiO3)을 각각 최대의 효과를 얻을 수 있는 비율을 확인하여 샘플을 제작하였다. 또한 액정과 고분자의 비율은 효과적인 산란과 높은 대비비를 얻기 위해 조절하여 결정하였다.
앞으로의 디스플레이 연구는 기존 디스플레이의 필요 요건이었던 경박단소(經薄短小)의 특성과 Flexible이 가능하고, 또한 PDLC 제작 공정의 차별화(Roll-to-Roll)를 통한 가격의 차별화를 가질 수 있는 방향으로 나아간다. 그러나 현재 PDLC의 단점으로는 디스플레이에서 사용되고 있는 TFT의 구동 범위 이상의 높은 전압을 통해 구동이 되고, 기존 디스플레이에 비해 낮은 Contrast Ratio 및 좁은 시야각을 갖는 문제점을 안고 있다. 그러므로 이번 연구에서는 시야각 개선과 동시에 구동전압을 낮추기 위한 방편으로 강유전성 Nanoparticle을 이용하였다. 본 연구는 PDLC의 광학적 특성을 비교하기 위하여 액정은 BL001을 고분자로는 NOA65를 사용하여 6:4의 블렌딩 비율을 고정시키고 반응의 진행을 위하여 HMPP(2 - Hydroxy - 2 - methyl - propiophenone)를 첨가하여 모세관 현상을 이용한 방법으로 액정과 고분자를 Cleaned ITO Galss 주입하고 UV로 고분자를 경화시켜 Referenc Cell을 제작하였고 이때 Cell Gap은 20μm로 유지시켰다. 기존에 연구가 진행되었던 시야각 개선을 위한 Nanoparticle (Melamine formaldehyde, Sb2O5, TiO2)을 첨가한 PDLC와 구동전압과 시야각 개선을 동시에 실현시킬 수 있는 강유전성 Nanoparticle (SrTiO3, BaTiO3)을 각각 최대의 효과를 얻을 수 있는 비율을 확인하여 샘플을 제작하였다. 또한 액정과 고분자의 비율은 효과적인 산란과 높은 대비비를 얻기 위해 조절하여 결정하였다.
Study of future display need light, thin, short, small and flexible. If its' developing is going methode of roll-to-roll we can manufacture cheaper PDLC. But PDLCs have a bad point. For example PDLS's operating voltage is higher than TFT's. And it has some problem about low contrast ratio and narrow...
Study of future display need light, thin, short, small and flexible. If its' developing is going methode of roll-to-roll we can manufacture cheaper PDLC. But PDLCs have a bad point. For example PDLS's operating voltage is higher than TFT's. And it has some problem about low contrast ratio and narrow viewing angle. So this study use ferrolerroelectricity nanoparticle for improving viewing angle and developing lower operating voltage. For preparing optical property, Liquid Crystal fixed knowing spec BL001 and prepolymer used NOA65. Then blending ratio of Liquid Crystal and prepolymer fixed 6:4. For polymerization we used HMPP(2 - Hydroxy - 2 - methyl - propiophenone). It behaves a good polymerization reactant to the monomer materials. This homogeneous mixture is introduced into the cleaned ITO glass by capillary action. UV exposure allows the monomer in the liquid crystal to polymerize, there by resulting in suppression of nonuniform nucleation and growth of the microdroplets. Moreover cell gap was fixed by 20μm spacer. For preparing of optical property we used two type nanoparticle there are nomal nanoparticle (Melamine formaldehyde, Sb2O5, TiO2) and ferrolerroelectricity nanoparticle (SrTiO3, BaTiO3). Normal nanoparticle was known about improving haze property and ferrolerroelectricity nanoparticle was known including it and about developing lower operating voltage. Ratio between the LC and prepolymer have been changed in order to get large number of LC droplets to enhance the scattering and contrast ratio.
Study of future display need light, thin, short, small and flexible. If its' developing is going methode of roll-to-roll we can manufacture cheaper PDLC. But PDLCs have a bad point. For example PDLS's operating voltage is higher than TFT's. And it has some problem about low contrast ratio and narrow viewing angle. So this study use ferrolerroelectricity nanoparticle for improving viewing angle and developing lower operating voltage. For preparing optical property, Liquid Crystal fixed knowing spec BL001 and prepolymer used NOA65. Then blending ratio of Liquid Crystal and prepolymer fixed 6:4. For polymerization we used HMPP(2 - Hydroxy - 2 - methyl - propiophenone). It behaves a good polymerization reactant to the monomer materials. This homogeneous mixture is introduced into the cleaned ITO glass by capillary action. UV exposure allows the monomer in the liquid crystal to polymerize, there by resulting in suppression of nonuniform nucleation and growth of the microdroplets. Moreover cell gap was fixed by 20μm spacer. For preparing of optical property we used two type nanoparticle there are nomal nanoparticle (Melamine formaldehyde, Sb2O5, TiO2) and ferrolerroelectricity nanoparticle (SrTiO3, BaTiO3). Normal nanoparticle was known about improving haze property and ferrolerroelectricity nanoparticle was known including it and about developing lower operating voltage. Ratio between the LC and prepolymer have been changed in order to get large number of LC droplets to enhance the scattering and contrast ratio.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.