과학 기술의 발달로 현대인들은 급변하는 사회에 발맞춰 의 ‧ 식 ‧ 주와 같은 기본적 욕구 충족에서 벗어나 개인 삶의 질을 향상시키는데 큰 관심을 갖게 되었다. 특히 21세기, 정보화시대에 들어서면서 사람들은 미디어에 대한 관심이 급증하였고, 이에 대한 산물로 PDP, LCD와 같은 디스플레이 시장이 활성화되어 왔다. 계속되는 디스플레이 시장의 발전은 대형화에 까지 이르렀으며 지속적인 개발이 연구되고 있다. 대형 디스플레이의 대표주자인 PDP의 경우, LCD에 비해 ...
과학 기술의 발달로 현대인들은 급변하는 사회에 발맞춰 의 ‧ 식 ‧ 주와 같은 기본적 욕구 충족에서 벗어나 개인 삶의 질을 향상시키는데 큰 관심을 갖게 되었다. 특히 21세기, 정보화시대에 들어서면서 사람들은 미디어에 대한 관심이 급증하였고, 이에 대한 산물로 PDP, LCD와 같은 디스플레이 시장이 활성화되어 왔다. 계속되는 디스플레이 시장의 발전은 대형화에 까지 이르렀으며 지속적인 개발이 연구되고 있다. 대형 디스플레이의 대표주자인 PDP의 경우, LCD에 비해 휘도, 콘트라스트, 색재현비율 등과 같은 부분에서 우수한 특성을 보이나 부품의 고가와 낮은 수율, 수명 등이 문제되고 있다. 이러한 문제는 PDP내부의 불순 가스에 의한 것이며, 이를 해결하기위해 새로운 게터의 개발이 요구되고 있다. 게터의 성능은 표면적이 증가와 관련 있으므로 게터로 사용될 수 있는 Ti와 Fe, 그리고 둘의 복합 성분을 열 플라즈마를 통해 제작해 그 특성을 분석해 보았다. 열 플라즈마는 나노 입자를 만드는데 우수한 특성을 보이는데, 이때 입자 생성의 변수로 인가 전류와 방전 가스의 유량이 중요시 된다. 따라서 두 변수의 변화를 통해 입자 생성의 특성을 알아보았다. Fe의 경우, 인가 전류를 200A ~ 240A까지 10A의 간격으로 구분하여 실험을 실시한 결과 평균적으로 20nm 크기의 결정질 입자가 생성되었음을 확인하였으며 전류를 증가시킴에 따라 입자의 크기는 작아졌으며 입자의 균일도가 증가하였으며, 입자 생성 반응시 산소의 유입이 없었음을 EDS 분석을 통해 확인하였다. Ti의 경우, Fe에 비해 비점이 높아서 전류 범위를 240A ~ 280A로 높여 실험하였으며 간격은 20A의 간격으로 수행하였다. TEM 분석 결과 입자의 크기는 10nm ~ 20nm 이었으며 전류가 증가함에 따라 Fe와 마찬가지로 입자 크기가 작아졌고 입자의 균일도 역시 증가하였다. 전류 240A로 고정 시켜두고 유량을 변수로 하여 실험하였다. 유량은 5ℓ/min ~ 15ℓ/min으로 5ℓ/min씩 증가시켰다. TEM분석 결과 전반적으로 10nm 안팎의 입자 크기가 생성되었다. 또한 유량의 증가에 따라 입자의 크기는 작아졌으며, 입자의 균일도가 증가 하였다. 마지막으로 Fe(20%)와 Ti(80%) 복합 성분을 가지고 실험을 하였을 경우, SEM 분석 결과 입자의 크기는 20nm이하의 작은 입자가 생성하였으며, 전류가 증가할수록 생성입자의 함량은 증가함을 보였다. 이는 전류의 증가에 따라 고온 범위가 증가하여 고비점의 Ti가 더 많이 생성될 수 있었기 때문으로 사료된다. 생성된 입자의 분포는 입자 전반에 걸쳐 Ti와 Fe가 고루 분포 하였으며 입자 하나에 대한 mapping을 한 결과 Fe입자와 Ti입자가 따로 생성되어 존재 하는 것이 아니라 한 입자에 Fe와 Ti가 공존하였다.
과학 기술의 발달로 현대인들은 급변하는 사회에 발맞춰 의 ‧ 식 ‧ 주와 같은 기본적 욕구 충족에서 벗어나 개인 삶의 질을 향상시키는데 큰 관심을 갖게 되었다. 특히 21세기, 정보화시대에 들어서면서 사람들은 미디어에 대한 관심이 급증하였고, 이에 대한 산물로 PDP, LCD와 같은 디스플레이 시장이 활성화되어 왔다. 계속되는 디스플레이 시장의 발전은 대형화에 까지 이르렀으며 지속적인 개발이 연구되고 있다. 대형 디스플레이의 대표주자인 PDP의 경우, LCD에 비해 휘도, 콘트라스트, 색재현비율 등과 같은 부분에서 우수한 특성을 보이나 부품의 고가와 낮은 수율, 수명 등이 문제되고 있다. 이러한 문제는 PDP내부의 불순 가스에 의한 것이며, 이를 해결하기위해 새로운 게터의 개발이 요구되고 있다. 게터의 성능은 표면적이 증가와 관련 있으므로 게터로 사용될 수 있는 Ti와 Fe, 그리고 둘의 복합 성분을 열 플라즈마를 통해 제작해 그 특성을 분석해 보았다. 열 플라즈마는 나노 입자를 만드는데 우수한 특성을 보이는데, 이때 입자 생성의 변수로 인가 전류와 방전 가스의 유량이 중요시 된다. 따라서 두 변수의 변화를 통해 입자 생성의 특성을 알아보았다. Fe의 경우, 인가 전류를 200A ~ 240A까지 10A의 간격으로 구분하여 실험을 실시한 결과 평균적으로 20nm 크기의 결정질 입자가 생성되었음을 확인하였으며 전류를 증가시킴에 따라 입자의 크기는 작아졌으며 입자의 균일도가 증가하였으며, 입자 생성 반응시 산소의 유입이 없었음을 EDS 분석을 통해 확인하였다. Ti의 경우, Fe에 비해 비점이 높아서 전류 범위를 240A ~ 280A로 높여 실험하였으며 간격은 20A의 간격으로 수행하였다. TEM 분석 결과 입자의 크기는 10nm ~ 20nm 이었으며 전류가 증가함에 따라 Fe와 마찬가지로 입자 크기가 작아졌고 입자의 균일도 역시 증가하였다. 전류 240A로 고정 시켜두고 유량을 변수로 하여 실험하였다. 유량은 5ℓ/min ~ 15ℓ/min으로 5ℓ/min씩 증가시켰다. TEM분석 결과 전반적으로 10nm 안팎의 입자 크기가 생성되었다. 또한 유량의 증가에 따라 입자의 크기는 작아졌으며, 입자의 균일도가 증가 하였다. 마지막으로 Fe(20%)와 Ti(80%) 복합 성분을 가지고 실험을 하였을 경우, SEM 분석 결과 입자의 크기는 20nm이하의 작은 입자가 생성하였으며, 전류가 증가할수록 생성입자의 함량은 증가함을 보였다. 이는 전류의 증가에 따라 고온 범위가 증가하여 고비점의 Ti가 더 많이 생성될 수 있었기 때문으로 사료된다. 생성된 입자의 분포는 입자 전반에 걸쳐 Ti와 Fe가 고루 분포 하였으며 입자 하나에 대한 mapping을 한 결과 Fe입자와 Ti입자가 따로 생성되어 존재 하는 것이 아니라 한 입자에 Fe와 Ti가 공존하였다.
As society changed rapidly, people have become basic needs. To improve the quality of life has been great interest, this is essential to modern man is to appear in the media sector. As a representative of a large display market is enabled. Currently a large display market and stands out is the PDP a...
As society changed rapidly, people have become basic needs. To improve the quality of life has been great interest, this is essential to modern man is to appear in the media sector. As a representative of a large display market is enabled. Currently a large display market and stands out is the PDP and LCD. Each other has advantages and disadvantage. PDP has disadvantage such as an expensive part, a lower yield and life issues. But the brightness, contrast, color reproduction ratio, gradation characteristics show a better performance. PDP's problems are due to the impurity gas. To solve the problem, apply the getter is required. Therefore, getter made by thermal plasma device. A thermal plasma device can generate ultra-fine particle size distribution is less straightforward process and has the advantage of continuous process possible. The case of Fe, is the current from 200A to 240A performed experiments at intervals of 10A. As a result, the particle size was 20nm, the crystalline particles were produced. Current by increasing the particle size was reduced, the increased uniformity of the particle. The case of Ti, Fe is higher than the boiling point. Therefore, is the current from 240A to 280A performed experiments at intervals of 20A. TEM analysis, the particle size was 10nm ~ 20nm, the current increased as particle size decreases, Fe was also increased uniformity of the particle. In flow experiments, flow rate is from 5ℓ/min to 15ℓ/ min performed experiments at intervals of 5ℓ/min. The particle size was 10nm ~ 20nm, the crystalline particles were produced. Flow rate by increasing the particle size was reduced, the increased uniformity of the particle. Finally, Fe (20%) and Ti (80%) case of experiments with multiple components, particle size were less than 20nm. And that reduced by increasing input current, the increased uniformity of the particle, the composite metal(Fe-Ti) particles were generated.
As society changed rapidly, people have become basic needs. To improve the quality of life has been great interest, this is essential to modern man is to appear in the media sector. As a representative of a large display market is enabled. Currently a large display market and stands out is the PDP and LCD. Each other has advantages and disadvantage. PDP has disadvantage such as an expensive part, a lower yield and life issues. But the brightness, contrast, color reproduction ratio, gradation characteristics show a better performance. PDP's problems are due to the impurity gas. To solve the problem, apply the getter is required. Therefore, getter made by thermal plasma device. A thermal plasma device can generate ultra-fine particle size distribution is less straightforward process and has the advantage of continuous process possible. The case of Fe, is the current from 200A to 240A performed experiments at intervals of 10A. As a result, the particle size was 20nm, the crystalline particles were produced. Current by increasing the particle size was reduced, the increased uniformity of the particle. The case of Ti, Fe is higher than the boiling point. Therefore, is the current from 240A to 280A performed experiments at intervals of 20A. TEM analysis, the particle size was 10nm ~ 20nm, the current increased as particle size decreases, Fe was also increased uniformity of the particle. In flow experiments, flow rate is from 5ℓ/min to 15ℓ/ min performed experiments at intervals of 5ℓ/min. The particle size was 10nm ~ 20nm, the crystalline particles were produced. Flow rate by increasing the particle size was reduced, the increased uniformity of the particle. Finally, Fe (20%) and Ti (80%) case of experiments with multiple components, particle size were less than 20nm. And that reduced by increasing input current, the increased uniformity of the particle, the composite metal(Fe-Ti) particles were generated.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.