랙크식 창고는 물품의 고직접 적재를 위해 여러 단의 선반위에 물건을 수직적으로 적재하는 방식으로 화재 발생 시 가연물에 의한 입체화재 형태로 빠른 화재 성장속도로 인해 막대한 피해가 발생하고 있다. 이러한 랙크식 창고에서 화재 피해를 최소화하기 위해서는 최신의 소화 설비와 초기에 적절히 소화할 수 있는 설비에 대한 연구가 필요하나 현재 창고 화재에 대한 특성 및 초기 소화에 대한 연구가 미흡한 실정이다. 스프링클러 설비는 화재를 감지하고 진압할 수 있는 고정식 설비로 전통적으로 가장 오래되었고 비교적으로 경제적이고 소화 성능이 우수한 설비이다. 이러한 스프링클러 설비가 랙크식 창고에 특별한 규정이나 기술 기준이 없이 인랙 스프링클러 헤드로 설치되고 사용된다면 설비의 성능 부족으로 인한 화재 초기 진압 실패는 거대한 랙 창고의 전소라는 재앙을 불러올 것이다. 이에 본 연구에서는 인랙에 적용되는 스프링클러 설비에 대한 소화 성능을 확보하고자 다양한 방향으로 연구를 진행하였다. 창고에 저장되는 수용 물품의 종류와 가장 위험한 가연물이 무엇인지 확인하기 위하여 적재 가연물 모양을 만들고 이들에 대한 단위 연소 시험을 수행하여 대표 가연물을 선정하였다. 또한 표준 랙의 규정 및 인랙 스프링클러 설치 기준을 반영하여 실험 모형을 만들었고, 이 모형을 통해 기존에 인랙 스프링클러 헤드로 나와 있는 제품을 구하여 기본 화재 실험 시나리오를 설정하여 실제 소화 시험을 수행하였다. 본 연구의 목표는 화세의 제어가 아니라 소화가 되는 조건을 만족하기 위한 실험이었고, 기존에 설치되어 있는 폐쇄형의 K-80과 K-115 값을 갖는 인랙 스프링클러 헤드로는 실증 화재실험 결과 소화가 불가능한 것으로 밝혀졌다. 따라서 본 연구에서는 1차 화재실험 결과로 얻은 자료를 바탕으로 초기 소화가 가능하다고 판단되는 ...
랙크식 창고는 물품의 고직접 적재를 위해 여러 단의 선반위에 물건을 수직적으로 적재하는 방식으로 화재 발생 시 가연물에 의한 입체화재 형태로 빠른 화재 성장속도로 인해 막대한 피해가 발생하고 있다. 이러한 랙크식 창고에서 화재 피해를 최소화하기 위해서는 최신의 소화 설비와 초기에 적절히 소화할 수 있는 설비에 대한 연구가 필요하나 현재 창고 화재에 대한 특성 및 초기 소화에 대한 연구가 미흡한 실정이다. 스프링클러 설비는 화재를 감지하고 진압할 수 있는 고정식 설비로 전통적으로 가장 오래되었고 비교적으로 경제적이고 소화 성능이 우수한 설비이다. 이러한 스프링클러 설비가 랙크식 창고에 특별한 규정이나 기술 기준이 없이 인랙 스프링클러 헤드로 설치되고 사용된다면 설비의 성능 부족으로 인한 화재 초기 진압 실패는 거대한 랙 창고의 전소라는 재앙을 불러올 것이다. 이에 본 연구에서는 인랙에 적용되는 스프링클러 설비에 대한 소화 성능을 확보하고자 다양한 방향으로 연구를 진행하였다. 창고에 저장되는 수용 물품의 종류와 가장 위험한 가연물이 무엇인지 확인하기 위하여 적재 가연물 모양을 만들고 이들에 대한 단위 연소 시험을 수행하여 대표 가연물을 선정하였다. 또한 표준 랙의 규정 및 인랙 스프링클러 설치 기준을 반영하여 실험 모형을 만들었고, 이 모형을 통해 기존에 인랙 스프링클러 헤드로 나와 있는 제품을 구하여 기본 화재 실험 시나리오를 설정하여 실제 소화 시험을 수행하였다. 본 연구의 목표는 화세의 제어가 아니라 소화가 되는 조건을 만족하기 위한 실험이었고, 기존에 설치되어 있는 폐쇄형의 K-80과 K-115 값을 갖는 인랙 스프링클러 헤드로는 실증 화재실험 결과 소화가 불가능한 것으로 밝혀졌다. 따라서 본 연구에서는 1차 화재실험 결과로 얻은 자료를 바탕으로 초기 소화가 가능하다고 판단되는 노즐의 분사형태, 유량, 개방 방식 등을 선택하여 새로운 형태의 인랙 전용 스프링클러 헤드를 개발하였다. 본 실험에서는 여러 개의 인랙 전용 헤드 목업을 만들고, 사전 분사 패턴 시험 등을 진행하였다. 이에 대한 초기 소화 성능을 검증하기 위해 실증화재 실험을 진행하여 인랙 스프링클러가 가져야 할 시스템 및 성능은 구역별로 나누어 수직 방향으로 일제 살수 방식으로 이루어져야 하며, 헤드의 K값은 115 이상이고 분사각도는 살수 각도는 120° ∼ 135° 이내로 제한되어야 한다. 또한 헤드는 화재가 발생한 시점에서 4분 30초 이내에 물을 분사하여야 하며, 헤드간의 수평 거리는 2.4 m 이내이고 복도 방향에도 동일한 간격으로 서로 엇갈리게 설치하여야 하고, 수직 거리는 랙의 단수인 2.5 m 이내에 설치하여야 한다. 적재물 가운데 설치되는 인랙 스프링클러 헤드는 송기공간의 가운데 위치하도록 설치하여야 한다. 실험 결과를 바탕으로 랙에 집중적으로 물을 살수 하여 초기에 소화 가능한 스마트 적층형 화재 시스템의 적용에 대하여 기술하였다. 본 연구 자료를 바탕으로 향후 대형 랙크식 창고에 대한 화재 방호 및 초기 소화와 초기 화재감지에 대한 연구에 활용될 수 있을 것으로 기대된다.
랙크식 창고는 물품의 고직접 적재를 위해 여러 단의 선반위에 물건을 수직적으로 적재하는 방식으로 화재 발생 시 가연물에 의한 입체화재 형태로 빠른 화재 성장속도로 인해 막대한 피해가 발생하고 있다. 이러한 랙크식 창고에서 화재 피해를 최소화하기 위해서는 최신의 소화 설비와 초기에 적절히 소화할 수 있는 설비에 대한 연구가 필요하나 현재 창고 화재에 대한 특성 및 초기 소화에 대한 연구가 미흡한 실정이다. 스프링클러 설비는 화재를 감지하고 진압할 수 있는 고정식 설비로 전통적으로 가장 오래되었고 비교적으로 경제적이고 소화 성능이 우수한 설비이다. 이러한 스프링클러 설비가 랙크식 창고에 특별한 규정이나 기술 기준이 없이 인랙 스프링클러 헤드로 설치되고 사용된다면 설비의 성능 부족으로 인한 화재 초기 진압 실패는 거대한 랙 창고의 전소라는 재앙을 불러올 것이다. 이에 본 연구에서는 인랙에 적용되는 스프링클러 설비에 대한 소화 성능을 확보하고자 다양한 방향으로 연구를 진행하였다. 창고에 저장되는 수용 물품의 종류와 가장 위험한 가연물이 무엇인지 확인하기 위하여 적재 가연물 모양을 만들고 이들에 대한 단위 연소 시험을 수행하여 대표 가연물을 선정하였다. 또한 표준 랙의 규정 및 인랙 스프링클러 설치 기준을 반영하여 실험 모형을 만들었고, 이 모형을 통해 기존에 인랙 스프링클러 헤드로 나와 있는 제품을 구하여 기본 화재 실험 시나리오를 설정하여 실제 소화 시험을 수행하였다. 본 연구의 목표는 화세의 제어가 아니라 소화가 되는 조건을 만족하기 위한 실험이었고, 기존에 설치되어 있는 폐쇄형의 K-80과 K-115 값을 갖는 인랙 스프링클러 헤드로는 실증 화재실험 결과 소화가 불가능한 것으로 밝혀졌다. 따라서 본 연구에서는 1차 화재실험 결과로 얻은 자료를 바탕으로 초기 소화가 가능하다고 판단되는 노즐의 분사형태, 유량, 개방 방식 등을 선택하여 새로운 형태의 인랙 전용 스프링클러 헤드를 개발하였다. 본 실험에서는 여러 개의 인랙 전용 헤드 목업을 만들고, 사전 분사 패턴 시험 등을 진행하였다. 이에 대한 초기 소화 성능을 검증하기 위해 실증화재 실험을 진행하여 인랙 스프링클러가 가져야 할 시스템 및 성능은 구역별로 나누어 수직 방향으로 일제 살수 방식으로 이루어져야 하며, 헤드의 K값은 115 이상이고 분사각도는 살수 각도는 120° ∼ 135° 이내로 제한되어야 한다. 또한 헤드는 화재가 발생한 시점에서 4분 30초 이내에 물을 분사하여야 하며, 헤드간의 수평 거리는 2.4 m 이내이고 복도 방향에도 동일한 간격으로 서로 엇갈리게 설치하여야 하고, 수직 거리는 랙의 단수인 2.5 m 이내에 설치하여야 한다. 적재물 가운데 설치되는 인랙 스프링클러 헤드는 송기공간의 가운데 위치하도록 설치하여야 한다. 실험 결과를 바탕으로 랙에 집중적으로 물을 살수 하여 초기에 소화 가능한 스마트 적층형 화재 시스템의 적용에 대하여 기술하였다. 본 연구 자료를 바탕으로 향후 대형 랙크식 창고에 대한 화재 방호 및 초기 소화와 초기 화재감지에 대한 연구에 활용될 수 있을 것으로 기대된다.
A rack-type warehouse is a facility of stacking objects vertically on several stages of shelves for direct loading of goods. In the case of a fire, the massive damages are occurring in rapid fire growth rate caused by the form of three-dimensional structure of combustible materials. In order to mini...
A rack-type warehouse is a facility of stacking objects vertically on several stages of shelves for direct loading of goods. In the case of a fire, the massive damages are occurring in rapid fire growth rate caused by the form of three-dimensional structure of combustible materials. In order to minimize the fire damage in the lack-type warehouse, it is necessary to study the latest fire-fighting equipment and facilities which can properly extinguish a fire in the early stage. Currently, there are not enough studies on fire characteristics and initial fire extinguishing to the warehouse. If the fixed sprinkler system is installed and used in rack-type warehouses without any special regulations or technical standards, the big disaster of the huge rack warehouse will be brought by failure of the initial fire suppression due to its poor performance. Therefore, this study was conducted in various directions to ensure the extinguishing performance of the sprinkler system which is applied to the in-rack.In order to identify the most dangerous combustible materials in the warehouse, a stacked combustible shape was made the mock-up and the unit combustible test was performed to select representative combustibles material in stocked. In addition, the experimental fire test model was made to reflect the standard rack and the in-rack sprinkler installation, the fire experiment was carried out with the existing in-rack sprinkler head by fire test scenarios. The basic target of this study was to satisfy the conditions of fire extinguishing rather than the fire control mode, experimental fire test results. It is not possible to extinguish the fire with existing K-80 and K-115 sprinkler heads of enclosed type. Based on the data obtained from the first fire test, we developed a new type of a specific in-rack sprinkler head by choosing the spraying type, flow rate, opening method, etc. We designed and made the several samples of in-rack S/P head, the samples had tested to spray pattern and K factor. To verify the initial fire extinguishing performance. The following conclusions were obtained through the demonstration of fire experiment ; it should be made by deluge sprinkler system type into divided or zoning though vertical sections; the K factor of the in-rack sprinkler head should be 115 or more, and the spray angle should be limited to 130 ° or less; the S/P head should spray water within 4 minutes and 30 seconds from the time of fire ignition; the horizontal distance between the in-rack sprinkler heads should be within 2.4m; the vertical distance of in-rack sprinkler head should be within 2.5 m of the rack height; the in-rack sprinkler heads installed in the load are to be installed in the center of the flue space. Based on this research data, it is expected that it can be used for performance - oriented design, and it is expected that future research on fire protection of large rack type warehouse will be utilized.
A rack-type warehouse is a facility of stacking objects vertically on several stages of shelves for direct loading of goods. In the case of a fire, the massive damages are occurring in rapid fire growth rate caused by the form of three-dimensional structure of combustible materials. In order to minimize the fire damage in the lack-type warehouse, it is necessary to study the latest fire-fighting equipment and facilities which can properly extinguish a fire in the early stage. Currently, there are not enough studies on fire characteristics and initial fire extinguishing to the warehouse. If the fixed sprinkler system is installed and used in rack-type warehouses without any special regulations or technical standards, the big disaster of the huge rack warehouse will be brought by failure of the initial fire suppression due to its poor performance. Therefore, this study was conducted in various directions to ensure the extinguishing performance of the sprinkler system which is applied to the in-rack.In order to identify the most dangerous combustible materials in the warehouse, a stacked combustible shape was made the mock-up and the unit combustible test was performed to select representative combustibles material in stocked. In addition, the experimental fire test model was made to reflect the standard rack and the in-rack sprinkler installation, the fire experiment was carried out with the existing in-rack sprinkler head by fire test scenarios. The basic target of this study was to satisfy the conditions of fire extinguishing rather than the fire control mode, experimental fire test results. It is not possible to extinguish the fire with existing K-80 and K-115 sprinkler heads of enclosed type. Based on the data obtained from the first fire test, we developed a new type of a specific in-rack sprinkler head by choosing the spraying type, flow rate, opening method, etc. We designed and made the several samples of in-rack S/P head, the samples had tested to spray pattern and K factor. To verify the initial fire extinguishing performance. The following conclusions were obtained through the demonstration of fire experiment ; it should be made by deluge sprinkler system type into divided or zoning though vertical sections; the K factor of the in-rack sprinkler head should be 115 or more, and the spray angle should be limited to 130 ° or less; the S/P head should spray water within 4 minutes and 30 seconds from the time of fire ignition; the horizontal distance between the in-rack sprinkler heads should be within 2.4m; the vertical distance of in-rack sprinkler head should be within 2.5 m of the rack height; the in-rack sprinkler heads installed in the load are to be installed in the center of the flue space. Based on this research data, it is expected that it can be used for performance - oriented design, and it is expected that future research on fire protection of large rack type warehouse will be utilized.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.