횡월류위어는 강변저류지나 off-line저류지의 유입부에 설치되는 구조물로 수로의 흐름방향과 평행하게 설치되어 유량관리 및 전환, 홍수통제, 에너지 소산, 수위조절, 일정 유량의 취수 및 분배, 초과 홍수량의 전환 등의 목적으로 이용되는 수공구조물이다. 현재 국내에 설치되어 있는 대부분의 횡월류위어는 수로의 흐름방향과 평행하게 설치되어 있다. 하지만 사행하천에 설치되는 횡월류위어의 경우 유입각을 수로방향과 평행하게 설치하지 못하는 경우가 발생하고 있으며, 그에 따른 구조물의 능력 검토가 필요한 실정이다. 금회 연구에서는 ...
횡월류위어는 강변저류지나 off-line저류지의 유입부에 설치되는 구조물로 수로의 흐름방향과 평행하게 설치되어 유량관리 및 전환, 홍수통제, 에너지 소산, 수위조절, 일정 유량의 취수 및 분배, 초과 홍수량의 전환 등의 목적으로 이용되는 수공구조물이다. 현재 국내에 설치되어 있는 대부분의 횡월류위어는 수로의 흐름방향과 평행하게 설치되어 있다. 하지만 사행하천에 설치되는 횡월류위어의 경우 유입각을 수로방향과 평행하게 설치하지 못하는 경우가 발생하고 있으며, 그에 따른 구조물의 능력 검토가 필요한 실정이다. 금회 연구에서는 3차원 상용프로그램인 FLOW-3D를 이용하여 사행하천에 설치되는 횡월류위어 유입각 변화에 따른 흐름특성 분석 및 유량계수식을 산정하였다. 사행하천구간에 설치되는 횡월류위어 유입각 변화에 따른 수치모형실험을 위해 3차원 AUTO CAD 프로그램을 이용하여 수로길이 450m, 수로폭 20m의 구형 사행하천을 구성하였고, 횡월류위어 유입부 각도를 0°∼50°로 변화시키며 수치모형실험을 수행하였다. 실험결과 횡월류위어 유입부의 각도가 증가할수록 Froude수와 본류수심에 대한 위어높이의 비가 증가하였고, 유량계수는 감소하였다. 이는 Jalili와 Borghei(1996), Borghei 등(1999)의 연구와 동일한 결과를 보였다. 수치모형 실험 결과를 바탕으로 회귀분석을 통해 횡월류위어 유입각 변화에 따른 유량계수식을 산정하였고, 그 결과 의 변화에 따른 유량계수식을 채택하였다.
횡월류위어는 강변저류지나 off-line저류지의 유입부에 설치되는 구조물로 수로의 흐름방향과 평행하게 설치되어 유량관리 및 전환, 홍수통제, 에너지 소산, 수위조절, 일정 유량의 취수 및 분배, 초과 홍수량의 전환 등의 목적으로 이용되는 수공구조물이다. 현재 국내에 설치되어 있는 대부분의 횡월류위어는 수로의 흐름방향과 평행하게 설치되어 있다. 하지만 사행하천에 설치되는 횡월류위어의 경우 유입각을 수로방향과 평행하게 설치하지 못하는 경우가 발생하고 있으며, 그에 따른 구조물의 능력 검토가 필요한 실정이다. 금회 연구에서는 3차원 상용프로그램인 FLOW-3D를 이용하여 사행하천에 설치되는 횡월류위어 유입각 변화에 따른 흐름특성 분석 및 유량계수식을 산정하였다. 사행하천구간에 설치되는 횡월류위어 유입각 변화에 따른 수치모형실험을 위해 3차원 AUTO CAD 프로그램을 이용하여 수로길이 450m, 수로폭 20m의 구형 사행하천을 구성하였고, 횡월류위어 유입부 각도를 0°∼50°로 변화시키며 수치모형실험을 수행하였다. 실험결과 횡월류위어 유입부의 각도가 증가할수록 Froude수와 본류수심에 대한 위어높이의 비가 증가하였고, 유량계수는 감소하였다. 이는 Jalili와 Borghei(1996), Borghei 등(1999)의 연구와 동일한 결과를 보였다. 수치모형 실험 결과를 바탕으로 회귀분석을 통해 횡월류위어 유입각 변화에 따른 유량계수식을 산정하였고, 그 결과 의 변화에 따른 유량계수식을 채택하였다.
The side weirs are hydraulic structures that are setup at a side of channel in the direction parallel to the River side reservoir or off line reservoir. The purpose of the facility is flow management and flood control, water level control, water intake and distribution of constant flow rate, the con...
The side weirs are hydraulic structures that are setup at a side of channel in the direction parallel to the River side reservoir or off line reservoir. The purpose of the facility is flow management and flood control, water level control, water intake and distribution of constant flow rate, the conversion of excess runoff. Presently, most of side weir constructed in our country have been installed parallel to the direction of flow. But sometimes, depending on the installation location for the side weir is parallel fails to install. That is why we need this study. In this study, flow characteristics and discharge coefficient for side weir inlet angle are simulated by the FLOW3D model which 3D numerical model. The 3D numerical model experiments was conducted in rectangular open channel of 20.0m size of width with 0°-50° of side weir inlet angle. A result, Fr and w/y increase as side weir angle increase. Additionally, the discharge coefficient decreased by increasing the inlet angle of side weir. This result, study of Jalili and Borghi(1996), Borghei etc(1999) has produced similar result. Through the analysis of regression with side weir inlet angle and w/y, formulae of discharge coefficient are presented and it's applicability is confirmed by comparing estimated, measured and numerical discharges over side weir.
The side weirs are hydraulic structures that are setup at a side of channel in the direction parallel to the River side reservoir or off line reservoir. The purpose of the facility is flow management and flood control, water level control, water intake and distribution of constant flow rate, the conversion of excess runoff. Presently, most of side weir constructed in our country have been installed parallel to the direction of flow. But sometimes, depending on the installation location for the side weir is parallel fails to install. That is why we need this study. In this study, flow characteristics and discharge coefficient for side weir inlet angle are simulated by the FLOW3D model which 3D numerical model. The 3D numerical model experiments was conducted in rectangular open channel of 20.0m size of width with 0°-50° of side weir inlet angle. A result, Fr and w/y increase as side weir angle increase. Additionally, the discharge coefficient decreased by increasing the inlet angle of side weir. This result, study of Jalili and Borghi(1996), Borghei etc(1999) has produced similar result. Through the analysis of regression with side weir inlet angle and w/y, formulae of discharge coefficient are presented and it's applicability is confirmed by comparing estimated, measured and numerical discharges over side weir.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.