본 연구는 콘크리트 물성에 도움을 주는 복합재료를 이용한 혼화제 합성 및 물리적 향상에 관한 연구를 다루었다. 흔히 일반 콘크리트 제품은 경제성 및 유지관리에 대한 효율성이 좋아 공단 조성이나 대규모 민간택지개발에 사용되고 있으나 콘크리트 제품의 타설, 시공 중 발생하는 문제점 및 노후로 인한 균열, 누수 등의 문제점등이 야기되고 있다. 따라서 누수 주변지역에서는 폐수와 하수의 지반 침투와 부식으로 인한 토양 및 지하수의 오염이 심각하다. 이러한 문제점을 해결하기 위해 콘크리트 혼화제의 개발 및 연구가 지금까지 진행 되고 있으나, 초보단계이다. 본 연구에서는 폴리카르본산계, 나프탈린계, 리그닌계 등의 복합재료를 이용하여 혼화제를 합성하였다. 합성된 혼화제는 분석기기인 FT-IR을 이용하여 반응 결과 및 혼화제의 물성을 확인하였다. 먼저 시멘트, 모래 1:2 비율로 교반 후 물과 1:1 비율로 혼합시켜 콘크리트를 제조하였다. 이 콘크리트에 혼화제를 각각 0~6 wt% (0, 2, 4, 6)씩 넣어 총 4종류의 공시체를 제조하였다. 해당 공시체는 KS F 2403규격에 따라 Ø100 × 200 mm 원형 공시체 형틀을 이용하여 만들었다. 제조된 공시체의 ...
본 연구는 콘크리트 물성에 도움을 주는 복합재료를 이용한 혼화제 합성 및 물리적 향상에 관한 연구를 다루었다. 흔히 일반 콘크리트 제품은 경제성 및 유지관리에 대한 효율성이 좋아 공단 조성이나 대규모 민간택지개발에 사용되고 있으나 콘크리트 제품의 타설, 시공 중 발생하는 문제점 및 노후로 인한 균열, 누수 등의 문제점등이 야기되고 있다. 따라서 누수 주변지역에서는 폐수와 하수의 지반 침투와 부식으로 인한 토양 및 지하수의 오염이 심각하다. 이러한 문제점을 해결하기 위해 콘크리트 혼화제의 개발 및 연구가 지금까지 진행 되고 있으나, 초보단계이다. 본 연구에서는 폴리카르본산계, 나프탈린계, 리그닌계 등의 복합재료를 이용하여 혼화제를 합성하였다. 합성된 혼화제는 분석기기인 FT-IR을 이용하여 반응 결과 및 혼화제의 물성을 확인하였다. 먼저 시멘트, 모래 1:2 비율로 교반 후 물과 1:1 비율로 혼합시켜 콘크리트를 제조하였다. 이 콘크리트에 혼화제를 각각 0~6 wt% (0, 2, 4, 6)씩 넣어 총 4종류의 공시체를 제조하였다. 해당 공시체는 KS F 2403규격에 따라 Ø100 × 200 mm 원형 공시체 형틀을 이용하여 만들었다. 제조된 공시체의 압축강도는 분석 기기인 UTM을 이용하여 7days, 14days, 21days 별로 7일마다 각각 3회 측정하여 평균값을 도출하였다. 혼화제의 wt%가 클수록 증가 되었고, 공시체의 경화가 진행되면서 압축강도가 점점 높아지는 것을 확인 하였다. 콘크리트의 문제점인 균열을 확인하기 위해 80℃에서 24시간 열풍건조 시킨 콘크리트를 5×5×0.1cm 크기의 시편으로 제작한 후, 주사전자현미경인 XL-30E SEM을 이용하여 표면을 촬영 하였다. 촬영 결과 혼화제의 wt%가 증가할수록 표면의 균열의 수와 깊이가 줄어드는 것을 확인하였다. 위와 같이 고분자 복합재료에 본 연구에서 합성된 혼화제를 첨가시킨 콘크리트의 물리적 성질을 조사한 결과, 콘크리트 제품을 혼화제 없이 사용하는 것보다 이를 이용하여 물리적 성질을 증가시켜 사용하는 것이 부식 및 누수 피해를 절감시킬 수 있었다.
본 연구는 콘크리트 물성에 도움을 주는 복합재료를 이용한 혼화제 합성 및 물리적 향상에 관한 연구를 다루었다. 흔히 일반 콘크리트 제품은 경제성 및 유지관리에 대한 효율성이 좋아 공단 조성이나 대규모 민간택지개발에 사용되고 있으나 콘크리트 제품의 타설, 시공 중 발생하는 문제점 및 노후로 인한 균열, 누수 등의 문제점등이 야기되고 있다. 따라서 누수 주변지역에서는 폐수와 하수의 지반 침투와 부식으로 인한 토양 및 지하수의 오염이 심각하다. 이러한 문제점을 해결하기 위해 콘크리트 혼화제의 개발 및 연구가 지금까지 진행 되고 있으나, 초보단계이다. 본 연구에서는 폴리카르본산계, 나프탈린계, 리그닌계 등의 복합재료를 이용하여 혼화제를 합성하였다. 합성된 혼화제는 분석기기인 FT-IR을 이용하여 반응 결과 및 혼화제의 물성을 확인하였다. 먼저 시멘트, 모래 1:2 비율로 교반 후 물과 1:1 비율로 혼합시켜 콘크리트를 제조하였다. 이 콘크리트에 혼화제를 각각 0~6 wt% (0, 2, 4, 6)씩 넣어 총 4종류의 공시체를 제조하였다. 해당 공시체는 KS F 2403규격에 따라 Ø100 × 200 mm 원형 공시체 형틀을 이용하여 만들었다. 제조된 공시체의 압축강도는 분석 기기인 UTM을 이용하여 7days, 14days, 21days 별로 7일마다 각각 3회 측정하여 평균값을 도출하였다. 혼화제의 wt%가 클수록 증가 되었고, 공시체의 경화가 진행되면서 압축강도가 점점 높아지는 것을 확인 하였다. 콘크리트의 문제점인 균열을 확인하기 위해 80℃에서 24시간 열풍건조 시킨 콘크리트를 5×5×0.1cm 크기의 시편으로 제작한 후, 주사전자현미경인 XL-30E SEM을 이용하여 표면을 촬영 하였다. 촬영 결과 혼화제의 wt%가 증가할수록 표면의 균열의 수와 깊이가 줄어드는 것을 확인하였다. 위와 같이 고분자 복합재료에 본 연구에서 합성된 혼화제를 첨가시킨 콘크리트의 물리적 성질을 조사한 결과, 콘크리트 제품을 혼화제 없이 사용하는 것보다 이를 이용하여 물리적 성질을 증가시켜 사용하는 것이 부식 및 누수 피해를 절감시킬 수 있었다.
In this study, admixture synthesis and its physical improvement using composite materials helpful for concrete property was handled. Generally, concrete product is used in industrial complex construction or large-scaled private housing land development owing to its excellent economic efficiency and ...
In this study, admixture synthesis and its physical improvement using composite materials helpful for concrete property was handled. Generally, concrete product is used in industrial complex construction or large-scaled private housing land development owing to its excellent economic efficiency and maintenance but its casting, construction trouble and cracking, leakage problem by deterioration are taken place. Therefore, around leakage area, contamination of soil and underground water by underground infiltration and corrosion of waste water and sewerage is serious. In order to solve this problem, development and research on concrete admixture have been progressed so far but it is at its early stage. In this study, admixture was synthesized by using composite materials like polycarboxylate, naphthalene line, lignin line. Reaction result and synthesized admixture property were confirmed by using FT-IR analyzer. First, concrete was manufactured by agitating it based on ratio of cement: sand=1:2 and mixed with water at the ratio of 1:1. 4 kinds of specimen were prepared by inserting each admixture 0~6 wt% (0, 2, 4, 6) into this concrete. Relevant specimen was manufactured by using circular mold (Ø100 × 200 mm) according to KS F 2403 standard. Average value of its compression strength was calculated by measuring it for 3 times every 7 days (7days, 14days, 21days) using UTM analyzer. It was confirmed that the more wt% of admixture was big and its hardening was progressed, its strength was increased. In order to confirm cracking of concrete, concrete test piece sized 5×5×0.1cm was manufactured by drying it under hot wind (80℃) for 24 hours and its surface was photographed by using XL-30E SEM (scanning microscopy). As its result, it was confirmed that the more admixture wt% was increased, number, depth of surface cracking were reduced. As a result of examining physical property of concrete in which synthesized admixture was added to polymer composite materials like above, it was learned that corrosion and leakage damage could be reduced by increasing physical property of concrete in case of adding admixture.
In this study, admixture synthesis and its physical improvement using composite materials helpful for concrete property was handled. Generally, concrete product is used in industrial complex construction or large-scaled private housing land development owing to its excellent economic efficiency and maintenance but its casting, construction trouble and cracking, leakage problem by deterioration are taken place. Therefore, around leakage area, contamination of soil and underground water by underground infiltration and corrosion of waste water and sewerage is serious. In order to solve this problem, development and research on concrete admixture have been progressed so far but it is at its early stage. In this study, admixture was synthesized by using composite materials like polycarboxylate, naphthalene line, lignin line. Reaction result and synthesized admixture property were confirmed by using FT-IR analyzer. First, concrete was manufactured by agitating it based on ratio of cement: sand=1:2 and mixed with water at the ratio of 1:1. 4 kinds of specimen were prepared by inserting each admixture 0~6 wt% (0, 2, 4, 6) into this concrete. Relevant specimen was manufactured by using circular mold (Ø100 × 200 mm) according to KS F 2403 standard. Average value of its compression strength was calculated by measuring it for 3 times every 7 days (7days, 14days, 21days) using UTM analyzer. It was confirmed that the more wt% of admixture was big and its hardening was progressed, its strength was increased. In order to confirm cracking of concrete, concrete test piece sized 5×5×0.1cm was manufactured by drying it under hot wind (80℃) for 24 hours and its surface was photographed by using XL-30E SEM (scanning microscopy). As its result, it was confirmed that the more admixture wt% was increased, number, depth of surface cracking were reduced. As a result of examining physical property of concrete in which synthesized admixture was added to polymer composite materials like above, it was learned that corrosion and leakage damage could be reduced by increasing physical property of concrete in case of adding admixture.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.