본 연구에서는 자동차의 Rear lamp lens, 건축용 Sheet, Bottle의 재활용 PC 소재를 분리, 분쇄, 압출하여 물성을 측정한 결과 Lens coated(PC/acrylate) 재료의 충격강도가 Virgin PC 대비 약 23%로 매우 낮 아 사용이 제한되었다. 건축용 Sheet, Bottle PC는 Virgin PC 대비 기계 적강도가 약 90~95%로 나타났으며 인장강도는 신재 PC 보다 오히려 약 10% 높은 결과를 나타내었다. XRF를 이용하여 4대 중금속과 난연제(Br) 의 첨가 유무를 확인한 결과 모든 Sample에서 기준치(100ppm)이하로 검 출되어 산업적으로 유용한 소재를 발견하였다. 건축용 Sheet PC와 이축압 출기를 이용하여 다양한 조성의 PC/ABS 블렌드 실험한 결과 ABS의 함량 이 증가할수록 MI는 증가하였고 인장강도, ...
본 연구에서는 자동차의 Rear lamp lens, 건축용 Sheet, Bottle의 재활용 PC 소재를 분리, 분쇄, 압출하여 물성을 측정한 결과 Lens coated(PC/acrylate) 재료의 충격강도가 Virgin PC 대비 약 23%로 매우 낮 아 사용이 제한되었다. 건축용 Sheet, Bottle PC는 Virgin PC 대비 기계 적강도가 약 90~95%로 나타났으며 인장강도는 신재 PC 보다 오히려 약 10% 높은 결과를 나타내었다. XRF를 이용하여 4대 중금속과 난연제(Br) 의 첨가 유무를 확인한 결과 모든 Sample에서 기준치(100ppm)이하로 검 출되어 산업적으로 유용한 소재를 발견하였다. 건축용 Sheet PC와 이축압 출기를 이용하여 다양한 조성의 PC/ABS 블렌드 실험한 결과 ABS의 함량 이 증가할수록 MI는 증가하였고 인장강도, 굴곡강도, 굴곡탄성율, 충격강 도, HDT는 감소하였다. ABS의 흐름성개선제인 EBS를 첨가하여 PC/ABS를 블렌드한 결과 전체적인 물성이 큰 폭 하락하였으며 이것은 EBS에 의해 PC의 물성이 영향 받은 결과로 판단 할 수 있다. Screw배열을 변화시켜 실험한 결과 3K2R이 2K2R보다 소폭 물성이 향상되었으며 이것은 스크류 배열중 Kneading Block의 추가로 레진의 혼련성 및 분산성이 증가한 결과 로 판단 할 수 있다. PC/ABS에 2종의 UV Stabilizer를 첨가하였으며 HALS 계를 첨가한 샘플에서 MI가 약 65~72% 증가하였다. UV조사 테스트 결 과 인장강도는 전체적으로 약 5~6%증가하였으며 충격강도는 UV Absorber를 사용한 샘플이 감소 폭이 -5~-12%, HALS계를 사용한 샘플의 하락 폭이 -24.7~-156%로 나타나 더 Brittle한 결과를 보였다. 즉, UV Absorber를 사용한 샘플이 더 좋은 결과를 획득하였으며 2종의 UV Stabilizer 함께 첨가된 샘플에서 시너지 효과는 확인되지 않았다. PC/ABS/ 나노알루미나 복합체를 나노알루미나의 함량을 증가시켜 실험하였으며 TEM으로 확인한 결과 나노알루미나가 매트릭스에 잘 분산되지 않고 뭉쳐 있어 기계적 강도 향상에 기여하지 못했고, 충격강도가 급격히 감소하였 다. PC/ABS/Organoclay 복합체의 TEM결과 organoclay는 층간의 간격만 조금 넓어지는 Intercalation을 보이며 organoclay가 완전히 분리되는 Exfoliation은 일어나지 않았다. PC/ABS/GF 복합체를 실험하였으며 GF의 함량이 증가할 수 록 인장강도, 굴곡강도, 굴곡탄성율, HDT는 증가하였고 신율, 충격강도는 큰 폭 하락 하였다. Impact Modifier를 이용하여 기계적 강도와 충격강도의 물성 Balance를 조절해야 할 것으로 사료된다.
본 연구에서는 자동차의 Rear lamp lens, 건축용 Sheet, Bottle의 재활용 PC 소재를 분리, 분쇄, 압출하여 물성을 측정한 결과 Lens coated(PC/acrylate) 재료의 충격강도가 Virgin PC 대비 약 23%로 매우 낮 아 사용이 제한되었다. 건축용 Sheet, Bottle PC는 Virgin PC 대비 기계 적강도가 약 90~95%로 나타났으며 인장강도는 신재 PC 보다 오히려 약 10% 높은 결과를 나타내었다. XRF를 이용하여 4대 중금속과 난연제(Br) 의 첨가 유무를 확인한 결과 모든 Sample에서 기준치(100ppm)이하로 검 출되어 산업적으로 유용한 소재를 발견하였다. 건축용 Sheet PC와 이축압 출기를 이용하여 다양한 조성의 PC/ABS 블렌드 실험한 결과 ABS의 함량 이 증가할수록 MI는 증가하였고 인장강도, 굴곡강도, 굴곡탄성율, 충격강 도, HDT는 감소하였다. ABS의 흐름성개선제인 EBS를 첨가하여 PC/ABS를 블렌드한 결과 전체적인 물성이 큰 폭 하락하였으며 이것은 EBS에 의해 PC의 물성이 영향 받은 결과로 판단 할 수 있다. Screw배열을 변화시켜 실험한 결과 3K2R이 2K2R보다 소폭 물성이 향상되었으며 이것은 스크류 배열중 Kneading Block의 추가로 레진의 혼련성 및 분산성이 증가한 결과 로 판단 할 수 있다. PC/ABS에 2종의 UV Stabilizer를 첨가하였으며 HALS 계를 첨가한 샘플에서 MI가 약 65~72% 증가하였다. UV조사 테스트 결 과 인장강도는 전체적으로 약 5~6%증가하였으며 충격강도는 UV Absorber를 사용한 샘플이 감소 폭이 -5~-12%, HALS계를 사용한 샘플의 하락 폭이 -24.7~-156%로 나타나 더 Brittle한 결과를 보였다. 즉, UV Absorber를 사용한 샘플이 더 좋은 결과를 획득하였으며 2종의 UV Stabilizer 함께 첨가된 샘플에서 시너지 효과는 확인되지 않았다. PC/ABS/ 나노알루미나 복합체를 나노알루미나의 함량을 증가시켜 실험하였으며 TEM으로 확인한 결과 나노알루미나가 매트릭스에 잘 분산되지 않고 뭉쳐 있어 기계적 강도 향상에 기여하지 못했고, 충격강도가 급격히 감소하였 다. PC/ABS/Organoclay 복합체의 TEM결과 organoclay는 층간의 간격만 조금 넓어지는 Intercalation을 보이며 organoclay가 완전히 분리되는 Exfoliation은 일어나지 않았다. PC/ABS/GF 복합체를 실험하였으며 GF의 함량이 증가할 수 록 인장강도, 굴곡강도, 굴곡탄성율, HDT는 증가하였고 신율, 충격강도는 큰 폭 하락 하였다. Impact Modifier를 이용하여 기계적 강도와 충격강도의 물성 Balance를 조절해야 할 것으로 사료된다.
In this study, the Rear lamp lens, Sheet, bottle PC material was separated, grinded, and extruded to measure physical properties. Lens coated (PC/acrylate) materials were very limited in use with a low impact strength of about 23% compared to Virgin PC. Sheets PC and Bottle PC had a ...
In this study, the Rear lamp lens, Sheet, bottle PC material was separated, grinded, and extruded to measure physical properties. Lens coated (PC/acrylate) materials were very limited in use with a low impact strength of about 23% compared to Virgin PC. Sheets PC and Bottle PC had a mechanical strength of about 90 to 95 percent compared to Virgin PC, and the tensile strength was about 10 percent higher than the new ones. Using XRF was measured with the presence or absence of the addition of the four heavy metals and flame retardants (Br). It is detected below the reference value (100ppm) in all samples were found to be industrially useful material. Experiments with PC/ABS blends of various composition using Sheet PC and Twin extruder showed MI increased as the content of ABS increased, and the tensile strength, flexural strength, flexural modulus, impact strength and HDT decreased. By the addition of the flowability improver EBS of ABS was a blend of PC / ABS. The overall physical properties have dropped significantly, which can be judged as a result of the physical properties of the PC affected by EBS. Experiments by varying screw arrangement changes have shown that 3K2R has slightly improved properties compared to 2K2R, which can be determined as a result of an additional increase in the mixing and dispersion of resin in the Kneading Block during screw arrangement. It was added to the PC / ABS two kinds of UV Stabilizer was increased mi by about 65-72% in the sample added hals-based. UV irradiation test results tensile strength was increased by about 5-6% as a whole, the impact strength was a sample using a UV Absorber reduced width -5-12%. The drop width of the sample using the HALS system was -24.7 to -156% showed a more Brittle result. That is, the sample using a UV Absorber was obtained a better result, the synergy effect was not confirmed in the sample added with two kinds of UV Stabilizer. PC / ABS / nanoalumina complex was tested by increasing the content of nanoalumina. TEM measurement results of the PC / ABS / Organoclay complex showed an Intercalation only slightly widening the gap between the layers exfoliation did not occur organoclay is completely separate. The PC/ABS/GF complex was tested and the contents of GF increased in number of Tensile strength, Flexural strength, Flexural modulus, HDT increased, and Elongation and impact strength decreased greatly. It is believed that the material balance of mechanical and impact strength should be adjusted using the Impact Modifier.
In this study, the Rear lamp lens, Sheet, bottle PC material was separated, grinded, and extruded to measure physical properties. Lens coated (PC/acrylate) materials were very limited in use with a low impact strength of about 23% compared to Virgin PC. Sheets PC and Bottle PC had a mechanical strength of about 90 to 95 percent compared to Virgin PC, and the tensile strength was about 10 percent higher than the new ones. Using XRF was measured with the presence or absence of the addition of the four heavy metals and flame retardants (Br). It is detected below the reference value (100ppm) in all samples were found to be industrially useful material. Experiments with PC/ABS blends of various composition using Sheet PC and Twin extruder showed MI increased as the content of ABS increased, and the tensile strength, flexural strength, flexural modulus, impact strength and HDT decreased. By the addition of the flowability improver EBS of ABS was a blend of PC / ABS. The overall physical properties have dropped significantly, which can be judged as a result of the physical properties of the PC affected by EBS. Experiments by varying screw arrangement changes have shown that 3K2R has slightly improved properties compared to 2K2R, which can be determined as a result of an additional increase in the mixing and dispersion of resin in the Kneading Block during screw arrangement. It was added to the PC / ABS two kinds of UV Stabilizer was increased mi by about 65-72% in the sample added hals-based. UV irradiation test results tensile strength was increased by about 5-6% as a whole, the impact strength was a sample using a UV Absorber reduced width -5-12%. The drop width of the sample using the HALS system was -24.7 to -156% showed a more Brittle result. That is, the sample using a UV Absorber was obtained a better result, the synergy effect was not confirmed in the sample added with two kinds of UV Stabilizer. PC / ABS / nanoalumina complex was tested by increasing the content of nanoalumina. TEM measurement results of the PC / ABS / Organoclay complex showed an Intercalation only slightly widening the gap between the layers exfoliation did not occur organoclay is completely separate. The PC/ABS/GF complex was tested and the contents of GF increased in number of Tensile strength, Flexural strength, Flexural modulus, HDT increased, and Elongation and impact strength decreased greatly. It is believed that the material balance of mechanical and impact strength should be adjusted using the Impact Modifier.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.