본 연구에서 구체방수 콘크리트의 방수성능을 평가하기 위해 상대습도 변화, 투수계수, 미세조직을 분석하였다. 구체 모형 실험체의 변수 즉, 압축강도, 수압, 구체두께에 따른 습도 변화에 대한 분석으로부터 다음과 같은 결과를 얻을 수 있었다. 첫째, 습도의 영향은 콘크리트의 압축강도가 높을수록 적게 받는다. 둘째, 습도의 영향은 콘크리트의 구체두께가 두꺼울수록, 천공두께가 얇을수록 적게 받는다. 셋째, 습도의 영향은 콘크리트에 작용하는 압력이 클수록 많이 받는다. 넷째, 일정한 압축강도와 구체두께를 제공하는 경우 콘크리트의 습도 변화가 거의 없고 수분 침투가 거의 없다. 다섯째, 콘크리트에 구체방수제를 혼입한 양이 많을수록 습도의 영향을 적게 받는다. 공시체 모형 실험체의 압축강도, 수압, 구체두께 및 구체방수제 혼입 양에 따른 변수별 습도변화를 분석한 결과는 다음과 같다. 첫째, 방수성능 효과는 콘크리트의 압축강도가 클수록, 구체두께가 두꺼울수록, 혼입방수제 양이 많을수록 향상된다. 둘째, 가하는 수압이 일정 이상일 경우에는 구체방수제를 혼입하더라도 방수성능이 상대적으로 감소하는 것으로 나타났다. 셋째, 상대적으로 높은 강도를 가지는 콘크리트의 경우, 습도 변화가 거의 없어 우수한 방수성능을 가진다는 것을 보여주었다. 구체방수 콘크리트 내 수분이동 정도의 정량적 평가를 위하여 투수계수를 산정하고 다음과 같은 결과를 얻을 수 있었다. 첫째, 콘크리트의 강도가 높을수록 투수계수는 작아진다. 둘째, 구체두께가 얇을수록 투수계수는 증가한다. 셋째, 구체방수제 혼입양이 많을수록 투수계수는 작아진다. 넷째, 구체방수제를 많이 혼입한 실험체의 투수계수는 구체방수제를 혼입하지 않은 실험체 값보다 아주 작다. 이것은 구체방수제가 콘크리트 내 ...
본 연구에서 구체방수 콘크리트의 방수성능을 평가하기 위해 상대습도 변화, 투수계수, 미세조직을 분석하였다. 구체 모형 실험체의 변수 즉, 압축강도, 수압, 구체두께에 따른 습도 변화에 대한 분석으로부터 다음과 같은 결과를 얻을 수 있었다. 첫째, 습도의 영향은 콘크리트의 압축강도가 높을수록 적게 받는다. 둘째, 습도의 영향은 콘크리트의 구체두께가 두꺼울수록, 천공두께가 얇을수록 적게 받는다. 셋째, 습도의 영향은 콘크리트에 작용하는 압력이 클수록 많이 받는다. 넷째, 일정한 압축강도와 구체두께를 제공하는 경우 콘크리트의 습도 변화가 거의 없고 수분 침투가 거의 없다. 다섯째, 콘크리트에 구체방수제를 혼입한 양이 많을수록 습도의 영향을 적게 받는다. 공시체 모형 실험체의 압축강도, 수압, 구체두께 및 구체방수제 혼입 양에 따른 변수별 습도변화를 분석한 결과는 다음과 같다. 첫째, 방수성능 효과는 콘크리트의 압축강도가 클수록, 구체두께가 두꺼울수록, 혼입방수제 양이 많을수록 향상된다. 둘째, 가하는 수압이 일정 이상일 경우에는 구체방수제를 혼입하더라도 방수성능이 상대적으로 감소하는 것으로 나타났다. 셋째, 상대적으로 높은 강도를 가지는 콘크리트의 경우, 습도 변화가 거의 없어 우수한 방수성능을 가진다는 것을 보여주었다. 구체방수 콘크리트 내 수분이동 정도의 정량적 평가를 위하여 투수계수를 산정하고 다음과 같은 결과를 얻을 수 있었다. 첫째, 콘크리트의 강도가 높을수록 투수계수는 작아진다. 둘째, 구체두께가 얇을수록 투수계수는 증가한다. 셋째, 구체방수제 혼입양이 많을수록 투수계수는 작아진다. 넷째, 구체방수제를 많이 혼입한 실험체의 투수계수는 구체방수제를 혼입하지 않은 실험체 값보다 아주 작다. 이것은 구체방수제가 콘크리트 내 공극을 메워 조직을 촘촘히 만들게 되는 공극충전 효과 때문이다. 투수계수 값을 검증하고 경향의 타당성을 검증하기 위하여 하이모스트럭 해석을 사용하였다. 모든 실험체에서 투수계수의 해석 결과는 유사한 경향을 나타내었고 실험결과가 해석결과보다 높은 투수계수 값을 보여주었다. 또한, 물시멘트비가 작을수록 시간당 투수계수가 감소하는 경향을 나타내었다. 이것은 물시멘트비가 작아지면 내부공극이 줄어들게 되면서 투수계수 값이 작아지는 것으로 판단된다. SEM-EDS 분석의 결과 C, Ca, Si, Al 4가지 원소가 가장 많이 검출되었다. 콘크리트 시료와 모르타르 시료 모두 유사한 특징으로 나타났다. 공극특성과 긍극량 분석으로부터 구체방수제를 많이 혼입한 실험체의 경우, 공극이 상대적으로 작아짐을 보여주었다. 그러므로 구체방수제가 공극의 크기에 영향을 미치며 결국 공극 충전에 관계하는 것으로 평가된다. X-선 형광분석 결과, 구체방수제에 가장 많이 함유된 성분은 CaO이며 그다음으로 SiO2, Al2O3, MgO가 많이 함유된 것으로 밝혀졌다. Ca와 Si, Al, Mg의 함유량이 많다는 것은 네 가지 성분이 구체방수제의 궁극 충전과 흡착력의 원인으로 추정된다. 그 중 Ca가 가장 중요한 역할을 담당하는 것으로 보인다. 이상의 결과로부터 본 연구에서 사용한 구체방수제가 공극 충전 효과를 높이고 내구성과 방수성을 향상하는 요인임을 알 수 있다. 또한, 상대적으로 고강도로 설계한 콘크리트에 구체방수제를 혼입한 경우와 일정한 피복두께를 확보한 콘크리트는 수압이 크지 않을 경우, 수분 침투가 일정 범위를 넘지 않을 것으로 판단된다. 특히, 구체방수제를 사용하기 위해 정확한 시공지침이 중요하다.
본 연구에서 구체방수 콘크리트의 방수성능을 평가하기 위해 상대습도 변화, 투수계수, 미세조직을 분석하였다. 구체 모형 실험체의 변수 즉, 압축강도, 수압, 구체두께에 따른 습도 변화에 대한 분석으로부터 다음과 같은 결과를 얻을 수 있었다. 첫째, 습도의 영향은 콘크리트의 압축강도가 높을수록 적게 받는다. 둘째, 습도의 영향은 콘크리트의 구체두께가 두꺼울수록, 천공두께가 얇을수록 적게 받는다. 셋째, 습도의 영향은 콘크리트에 작용하는 압력이 클수록 많이 받는다. 넷째, 일정한 압축강도와 구체두께를 제공하는 경우 콘크리트의 습도 변화가 거의 없고 수분 침투가 거의 없다. 다섯째, 콘크리트에 구체방수제를 혼입한 양이 많을수록 습도의 영향을 적게 받는다. 공시체 모형 실험체의 압축강도, 수압, 구체두께 및 구체방수제 혼입 양에 따른 변수별 습도변화를 분석한 결과는 다음과 같다. 첫째, 방수성능 효과는 콘크리트의 압축강도가 클수록, 구체두께가 두꺼울수록, 혼입방수제 양이 많을수록 향상된다. 둘째, 가하는 수압이 일정 이상일 경우에는 구체방수제를 혼입하더라도 방수성능이 상대적으로 감소하는 것으로 나타났다. 셋째, 상대적으로 높은 강도를 가지는 콘크리트의 경우, 습도 변화가 거의 없어 우수한 방수성능을 가진다는 것을 보여주었다. 구체방수 콘크리트 내 수분이동 정도의 정량적 평가를 위하여 투수계수를 산정하고 다음과 같은 결과를 얻을 수 있었다. 첫째, 콘크리트의 강도가 높을수록 투수계수는 작아진다. 둘째, 구체두께가 얇을수록 투수계수는 증가한다. 셋째, 구체방수제 혼입양이 많을수록 투수계수는 작아진다. 넷째, 구체방수제를 많이 혼입한 실험체의 투수계수는 구체방수제를 혼입하지 않은 실험체 값보다 아주 작다. 이것은 구체방수제가 콘크리트 내 공극을 메워 조직을 촘촘히 만들게 되는 공극충전 효과 때문이다. 투수계수 값을 검증하고 경향의 타당성을 검증하기 위하여 하이모스트럭 해석을 사용하였다. 모든 실험체에서 투수계수의 해석 결과는 유사한 경향을 나타내었고 실험결과가 해석결과보다 높은 투수계수 값을 보여주었다. 또한, 물시멘트비가 작을수록 시간당 투수계수가 감소하는 경향을 나타내었다. 이것은 물시멘트비가 작아지면 내부공극이 줄어들게 되면서 투수계수 값이 작아지는 것으로 판단된다. SEM-EDS 분석의 결과 C, Ca, Si, Al 4가지 원소가 가장 많이 검출되었다. 콘크리트 시료와 모르타르 시료 모두 유사한 특징으로 나타났다. 공극특성과 긍극량 분석으로부터 구체방수제를 많이 혼입한 실험체의 경우, 공극이 상대적으로 작아짐을 보여주었다. 그러므로 구체방수제가 공극의 크기에 영향을 미치며 결국 공극 충전에 관계하는 것으로 평가된다. X-선 형광분석 결과, 구체방수제에 가장 많이 함유된 성분은 CaO이며 그다음으로 SiO2, Al2O3, MgO가 많이 함유된 것으로 밝혀졌다. Ca와 Si, Al, Mg의 함유량이 많다는 것은 네 가지 성분이 구체방수제의 궁극 충전과 흡착력의 원인으로 추정된다. 그 중 Ca가 가장 중요한 역할을 담당하는 것으로 보인다. 이상의 결과로부터 본 연구에서 사용한 구체방수제가 공극 충전 효과를 높이고 내구성과 방수성을 향상하는 요인임을 알 수 있다. 또한, 상대적으로 고강도로 설계한 콘크리트에 구체방수제를 혼입한 경우와 일정한 피복두께를 확보한 콘크리트는 수압이 크지 않을 경우, 수분 침투가 일정 범위를 넘지 않을 것으로 판단된다. 특히, 구체방수제를 사용하기 위해 정확한 시공지침이 중요하다.
In this study, changes in relative humidity, water permeability and microstructure were analyzed to evaluate the waterproof performance of waterproofing concrete. The analysis results of humidity changes such as compressive strength, water pressure and structural thickness of the model specimen ...
In this study, changes in relative humidity, water permeability and microstructure were analyzed to evaluate the waterproof performance of waterproofing concrete. The analysis results of humidity changes such as compressive strength, water pressure and structural thickness of the model specimen are as follows. First, the higher the compressive strength of concrete, the less the influence of humidity is. Second, the influence of humidity is less as the concrete thickness is thicker and the perforation thickness is thinner. Third, the higher the pressure acting on the concrete, the greater the influence of humidity. The relationship between water pressure and humidity is proportional. Fourth, in the case of providing constant compressive strength and structure thickness (in this case, the strength of 27MPa and thickness of 140mm) concrete has little change in humidity and no penetration of humidity. From this, it can be seen that the waterproof effect is sufficient if the concrete thickness is more than 150mm. Fifth, the greater the amount of concrete waterproofing agent mixed, the less affected by humidity. The amount of concrete waterproofing agent mixed, water permeability and permeability coefficient are inversely proportional. In the case of a cylindrical specimen model, the results of analyzing the humidity change by variables (ie, compressive strength, water pressure, structure thickness, amount of mixed waterproofing agent) are as follows. First, the effect of waterproofing performance is improved as the compressive strength of the concrete increases, the thickness of the spheres increases and the amount of the mixed waterproofing agent increases. Second, it was shown that when the applied water pressure is more than 1.0bar, the waterproof performance is degraded even if the concrete waterproofing agent is mixed at 20mm and 70mm thick Third, relative to the above case, it was shown that in the case of concrete with a concrete thickness of 140mm having a strength of 27MPa, it has waterproof performance without changing humidity. For the quantitative evaluation of the degree of water movement in waterproof concrete, the water permeability coefficient was calculated. First, the water permeability coefficient decreases as the strength of concrete increases. Second, the thinner the sphere, the higher the permeability coefficient. Third, the greater the amount of the mixed waterproofing agent, the smaller the permeability coefficient. Fourth, the water permeability coefficient of the specimen with a large amount of waterproofing agent mixed with the waterproofing agent is much smaller than that of the specimen without mixing the waterproofing agent. (More than 1/50 in the case of this study) This is due to the pore-filling effect that the waterproofing agent fills the pores in the concrete and makes the structure compact. HYMOSTRUC analysis was used to verify the permeability coefficient value and to verify the permeability trend. As a result of the analysis, the evaluation of the permeability coefficient in all the specimens showed a similar trend. The experimental results showed higher values of the permeability coefficient than the analysis. As the water cement ratio was lower, the permeability coefficient per hour tended to decrease. It was evaluated that when the water-cement ratio decreased, the value of the permeability coefficient decreased as the inner voids decreased. As a result of SEM-EDS analysis, the four elements C, Ca, Si and Al were most often detected. Both concrete and mortar samples show very similar characteristics. The pore size of the test sample mixed with the waterproof agent is small, and the pore size is relatively small in the case of the test sample mixed with a large amount. Therefore, it is evaluated that the concrete waterproofing agent affects the size of the pores and eventually relates to the pore filling. As a result of X-ray fluorescence analysis, it was found that the most frequently contained component in the concrete waterproofing agent was CaO followed by SiO2, Al2O3 and MgO. The high content of Ca, Si, Al and Mg is believed to be the cause of the adsorption power of the concrete waterproofing agent by four components. Among them, Ca plays the most important role. From the above results, it can be seen that the concrete waterproofing agent is a factor that increases the void filling effect and improves durability and waterproofness.
In this study, changes in relative humidity, water permeability and microstructure were analyzed to evaluate the waterproof performance of waterproofing concrete. The analysis results of humidity changes such as compressive strength, water pressure and structural thickness of the model specimen are as follows. First, the higher the compressive strength of concrete, the less the influence of humidity is. Second, the influence of humidity is less as the concrete thickness is thicker and the perforation thickness is thinner. Third, the higher the pressure acting on the concrete, the greater the influence of humidity. The relationship between water pressure and humidity is proportional. Fourth, in the case of providing constant compressive strength and structure thickness (in this case, the strength of 27MPa and thickness of 140mm) concrete has little change in humidity and no penetration of humidity. From this, it can be seen that the waterproof effect is sufficient if the concrete thickness is more than 150mm. Fifth, the greater the amount of concrete waterproofing agent mixed, the less affected by humidity. The amount of concrete waterproofing agent mixed, water permeability and permeability coefficient are inversely proportional. In the case of a cylindrical specimen model, the results of analyzing the humidity change by variables (ie, compressive strength, water pressure, structure thickness, amount of mixed waterproofing agent) are as follows. First, the effect of waterproofing performance is improved as the compressive strength of the concrete increases, the thickness of the spheres increases and the amount of the mixed waterproofing agent increases. Second, it was shown that when the applied water pressure is more than 1.0bar, the waterproof performance is degraded even if the concrete waterproofing agent is mixed at 20mm and 70mm thick Third, relative to the above case, it was shown that in the case of concrete with a concrete thickness of 140mm having a strength of 27MPa, it has waterproof performance without changing humidity. For the quantitative evaluation of the degree of water movement in waterproof concrete, the water permeability coefficient was calculated. First, the water permeability coefficient decreases as the strength of concrete increases. Second, the thinner the sphere, the higher the permeability coefficient. Third, the greater the amount of the mixed waterproofing agent, the smaller the permeability coefficient. Fourth, the water permeability coefficient of the specimen with a large amount of waterproofing agent mixed with the waterproofing agent is much smaller than that of the specimen without mixing the waterproofing agent. (More than 1/50 in the case of this study) This is due to the pore-filling effect that the waterproofing agent fills the pores in the concrete and makes the structure compact. HYMOSTRUC analysis was used to verify the permeability coefficient value and to verify the permeability trend. As a result of the analysis, the evaluation of the permeability coefficient in all the specimens showed a similar trend. The experimental results showed higher values of the permeability coefficient than the analysis. As the water cement ratio was lower, the permeability coefficient per hour tended to decrease. It was evaluated that when the water-cement ratio decreased, the value of the permeability coefficient decreased as the inner voids decreased. As a result of SEM-EDS analysis, the four elements C, Ca, Si and Al were most often detected. Both concrete and mortar samples show very similar characteristics. The pore size of the test sample mixed with the waterproof agent is small, and the pore size is relatively small in the case of the test sample mixed with a large amount. Therefore, it is evaluated that the concrete waterproofing agent affects the size of the pores and eventually relates to the pore filling. As a result of X-ray fluorescence analysis, it was found that the most frequently contained component in the concrete waterproofing agent was CaO followed by SiO2, Al2O3 and MgO. The high content of Ca, Si, Al and Mg is believed to be the cause of the adsorption power of the concrete waterproofing agent by four components. Among them, Ca plays the most important role. From the above results, it can be seen that the concrete waterproofing agent is a factor that increases the void filling effect and improves durability and waterproofness.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.