최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기大韓機械學會論文集. Transactions of the Korean Society of Mechanical Engineers. A. A, v.26 no.2 = no.197, 2002년, pp.340 - 348
양상식 (포항공과대학교 대학원 기계공학과) , 권태헌
Deformation analysis of injection molded articles whose geometry is considered as the assembly of thin flat plates has been conducted. For the in-mold analysis, thermo-viscoelastic stress calculation of thermo-rheologically simple amorphous polymer and in-mold deformation calculation considering the...
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
Kim, I. H., Park, S. J., Chung, S. T. and Kwon, T. H. 1999, 'Numerical Modeling of Injection/Compression Molding for Center-Gated Disk: Part I. Injection Molding with Viscolastic Compression Fluid Model,' Polymer Engineering and Science, Vol. 39, No. 10, pp. 1930-1942
Kim, I. H., Park, S. J., Chung, S. T. and Kwon, T. H., 1999, 'Numerical Modeling of Injection/Compression Molding for Center-Gated Disk: Part Ⅱ. Effect of Compression Stage,' Polymer Engineering and Science, Vol. 39, No. 10, pp. 1943-1951
Lee, Y. B., Kwon, T. H. and Yoon, K. H., 'Numerical Prediction of Residual Stresses and Birefringences in Injection/Compression Molded Center-gated Disk: Part Ⅱ. Basic Modeling and Results for Injection Molding,' submitted to Polymer Engineering Science
Lee, Y. B., Kwon, T. H. and Yoon, K. H., 'Numerical Prediction of Residual Stresses and Birefringences in Injection/Compression Molded Center-gated Disk: Part II. Effects of Processing Conditions,' submitted to Polymer Engineering Science
St. Jacques, Michael, 1982, 'An Analysis of Thernal Warpage in Injection Molded Flat Parts Due to Unbalanced Cooling,' Polymer Engineering and Science, Vol. 22, No. 4, pp. 241-247
Jansen, K. M. B., 1994, 'Residual Stresses in Quenched and Injection Moulded Products,' International Polymer Processing, IX, pp. 82-89
Lee, E. H., Rogers, T. G. and Woo, T. C., 1965, 'Residual Stresses in a Glass Plate Cooled Symmetrically from Both Surfaces,'Journal of the American Ceramic Society, Vol. 48, No. 9, pp. 480-487
Santhanam, N., Chiang, H. H., Himasekhar, K., Tuschak, Peter and Wang, K. K., 1992, 'Postmolding and Load-Induced Deformation Analysis of Plastic Parts in the Injection Molding Process,' Advances in Polymer Technology, Vol. 11, No. 2, pp. 77-89
Kabanemi, K. K., Vaillancourt, H., W.ang, H. and Salloum, G., 1998, 'Residual Stresses, Shrinkage, and Warpage of Complex injection Molded Products: Numerical Simulation and Experimental Validation,' Polymer Engineering and Science, Vol. 38, No. 1, pp. 21-37
Wang, H., Kabanemi, K. K.and Salloum, G., 2000, 'Numerical and Experimental Studies on the Ejection of Injection-Molded Plastic Products,' Polymer Engineering and Science, Vol. 40, No. 3, pp. 826-840
Chiang, H. H., Hieber, C. A. and Wang, K. K., 1991, 'A Unified Simulation of the Filling and Postfilling Stages in Injection Molding: Part I. Formulation,' Polymer Engineering and Science, Vol. 31, No. 2, pp. 116-124
Chiang, H. H., Hieber, C. A. and Wang, K. K., 1991, 'A Unified Simulation of the Filling and Postfilling Stages in Injection Molding Part II: Experimental Validation,' Polymer Engineering and Science, Vol. 31, No. 2, pp. 125-139
Leonov, A. I., 1976, 'Non-equilibrium Thermo-dynamics and Rheology of Viscoelastic Polymer Media,' Rheol. Acta, Vol. 15, pp.85-98
Tait, T. G., 1988, Physics and Chemistry of the Voyage of H.M.S. Challenge, Scientific Papers LXI, Vol. II, p. 1
Shyu, G. D., 1993, 'Birefringence and Residual Stresses in Molded Articles of Amorphous Polymers,' PhD thesis, The University of Akron
Jansen, K. M. B., Pantani, R. and Titomanlio, G., 1998, 'As-Molded Shrinkage Measurements on Polystyrene Injection Molded Products,' Polymer Engineering and Science, Vol. 38, No. 2, pp. 254-264
Bergan, P. G. and Felippa, C. A., 1985, 'A Triangular Membrane Element with Rotational Degrees of Freedom,' Computer Methods in Applied Mechanics and Engineering, Vol. 50, pp. 25-69
Batoz, J. C., Bathe, C. J. and Ho, L. W., 1980, 'A Study of Three-Node Triangular Plate Bending Elements,' International Journal for Numerical Methods in Engineering, Vol. 15, pp. 1771-1812
*원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.