Statement of problem Metal-ceramic restorations have been used extensively by dental clinicians for nearly 40 years. Strength an functional ability of metal-ceramic restorations are proved to be satisfying, However esthetics and biocompatibility of metal alloy which is used in metal-ceramic restorat...
Statement of problem Metal-ceramic restorations have been used extensively by dental clinicians for nearly 40 years. Strength an functional ability of metal-ceramic restorations are proved to be satisfying, However esthetics and biocompatibility of metal alloy which is used in metal-ceramic restoration is not ideal. Using pure gold as an alternative, have advantage of esthetics, biocompatibility over conventional metal alloy. But there had been little article which studied on the color effect of pure gold on fual porcelain color. Purpose The purpose of this study was to spectrophotometrically evaluate the difference between color of metal alloy(Au-Pt, Ni-Cr) and pure gold, during color masking procedure with opaque porcelain and to analyze the differences, Material and Methods Three types of metal - base metal(Ni-Cr), high gold alloy(Au-Pt), pure gold(GES) - specimen were fabricated 1cm in diameter. Four steps were established - after finishing, after pre-coditioning, after application of first opaque porcelain(0.08mm in thickness), after application of second opaque porcelain(0.15mm in thickness)- and tested color with spectrophotometer every each steps and analyzed with $CIEL^*a^*b^*$ color order system. One-Way ANOVA test was used to and out if there were significant differences between groups tested and Shaffe multiple comparison was used to identify where the differences were. Results 1. After finishing and pre-conditioning, pure gold(GES) group showed most high values in $L^*,a^*,b^*$. 2. After application of first opaque porcelain(0.08mm in thickness), after application of second opaque porcelain(0.15mm in thickness), pure gold(GES) group showed the least difference in $L^*,a^*,b^*$ values and the lowest ${\Delta}E$ value(${\Delta}E$=0.63). 3. After application of first opaque porcelain and after application of second opaque porcelain differences that were significant (P<0.05) between groups were found only in $a^*$ values. 4. Base metal alloy group showed the lowest $a^*$ value in test after application of first opaque porcelain and the highest value in test after application of first opaque porcelain Conclusion Pure gold group and high gold group showed higher $a^*$ values than base metal group when tested after 0.08mm thickness of opaque porcelain was applied and pure gold group showed much similar $L^*,a^*,b^*$ values between 0.08mm thickness and 0.15mm thickness of opaque porcelain. This meant that pure gold was more easily masked by opaque porcelain than the other two groups.
Statement of problem Metal-ceramic restorations have been used extensively by dental clinicians for nearly 40 years. Strength an functional ability of metal-ceramic restorations are proved to be satisfying, However esthetics and biocompatibility of metal alloy which is used in metal-ceramic restoration is not ideal. Using pure gold as an alternative, have advantage of esthetics, biocompatibility over conventional metal alloy. But there had been little article which studied on the color effect of pure gold on fual porcelain color. Purpose The purpose of this study was to spectrophotometrically evaluate the difference between color of metal alloy(Au-Pt, Ni-Cr) and pure gold, during color masking procedure with opaque porcelain and to analyze the differences, Material and Methods Three types of metal - base metal(Ni-Cr), high gold alloy(Au-Pt), pure gold(GES) - specimen were fabricated 1cm in diameter. Four steps were established - after finishing, after pre-coditioning, after application of first opaque porcelain(0.08mm in thickness), after application of second opaque porcelain(0.15mm in thickness)- and tested color with spectrophotometer every each steps and analyzed with $CIEL^*a^*b^*$ color order system. One-Way ANOVA test was used to and out if there were significant differences between groups tested and Shaffe multiple comparison was used to identify where the differences were. Results 1. After finishing and pre-conditioning, pure gold(GES) group showed most high values in $L^*,a^*,b^*$. 2. After application of first opaque porcelain(0.08mm in thickness), after application of second opaque porcelain(0.15mm in thickness), pure gold(GES) group showed the least difference in $L^*,a^*,b^*$ values and the lowest ${\Delta}E$ value(${\Delta}E$=0.63). 3. After application of first opaque porcelain and after application of second opaque porcelain differences that were significant (P<0.05) between groups were found only in $a^*$ values. 4. Base metal alloy group showed the lowest $a^*$ value in test after application of first opaque porcelain and the highest value in test after application of first opaque porcelain Conclusion Pure gold group and high gold group showed higher $a^*$ values than base metal group when tested after 0.08mm thickness of opaque porcelain was applied and pure gold group showed much similar $L^*,a^*,b^*$ values between 0.08mm thickness and 0.15mm thickness of opaque porcelain. This meant that pure gold was more easily masked by opaque porcelain than the other two groups.
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
문제 정의
이러한 시각적 오차가 없이 객관적으로 비교 분석하기 위한 방법으로 분광측색 분석이 있는데, 이것은 서로 다른 색의 분광반사율을 측정하여 이를 숫자로 환산하는 것으로 "이를 측정하는 장치로 분광측색 장치 (spectrophotometer) 가 있다. 또한 색조에 대한 정량적 분석을 위해서는 색조를 수치로 나타내는 색체계가 필요한데, 1978년 국제 조명 위원회 (Commision Intenationale de JEclairage)에 의해 개발된 CIE L*a*b* 색체계는 색조를 L*, a*, b*의 3가지의 빛의 속성을 사용하여 정성적 및 정량적으로 색조을 비교 분석이 가능하며 연구 목적으로 적합한 색체계이다.
본 연구에서는 순금의 색조와 다른 합금의 색조가 도 재의 색조에 어떠한 영향을 미치는 지에 대하여 객관적으로 비교해 보고자 함을 그 목적으로 하였으며, 분광측색장치를 이용하여 CIEL*a*b* 색체계로 금속 하부구조물에 따른 도재의 색조 차이를 비교 분석하였다.
가설 설정
1. After finishing and pre-conditioning, pure gold(GES) group showed most high values in L*, a*, b*.
제안 방법
3차 색측정은 평균 0.08mm로 불투명 도재를 한번 도포한 후 시행하였고, 4차 색측정은 평균 0.15mm 두께로 불투명 도재를 두 번 도포한 후 시행하였다.
fabricated 1cm in diameter. Four steps were established - after finishing , after pre-codi- tioning, after application of first opaque porcelain (0.08mm in thickness), after application of sec ond opaque porcelain(0.15mm in thickness)- and tested color with spectrophotometer every each steps and analyzed with CIEL*a*b* color order system. One-Way ANOVA test was used to find out if there were significant differences between groups tested and Shafife multiple comparison was used to identify where the differences were.
The purpose of this study was to spectrophotometrically evaluate the difference between color of metal alloy(Au-Pt, Ni-Cr) and pure gold, during color masking procedure with opaque porcelain and to analyze the differences.
금의 침착을 위해서 모형의 금이 침착될 면에 전도은(Silver lacquer, Gramm Co., Tiefebronn- Muhlhausen, Germany)을 도포하고, 시편 당 전해질(Ecolyt SG 100, Gramm Co, , Tiefebronn-Muhlhausen, Germany) 40mi와 제조사의 지시에 따라 촉진제 (Activator SG 100, Gramm Co., Tiefebronn~Muhlhausen, Germany)를 첨가한 후, Gold electrofbming system을 이용하여 전기 주형(electroforming)을 시행하였다(Fig. 5).
, Japan) 모형을 제작하였다. 동선(Copper wire white, Gramm Co., Germany)을 모형에서 금이 침착 될 면의 1mm 하방에 tapered fissure bur를 이용하여 구멍 을 형성 한 후 여기에 동선을 연결하였다(Fig. 4).
본 연구에서는 3차 측정값과 4차 측정값의 ZE 수치를 비교하였다(Table 3).
비귀금속군 (base metal alloy) 을 제 1군, 금합금 (high gold alloy) 군을 제2군, Gold electroforming system을 이용한 순금 군을 제 3군으로 설정하였으며, 시편 수는 군 당 10개로 설정하였다(Fig. 6).
Osaka, Japan)으로동남아 지역에서 밝은날 오전 11시를 기준으로 하는 광원인 C광원(6774K)를 사용하였다. 색조측정을 위하여 표준백색판으로 영점을 조정한 후, 5mm의 측정경에 시편을 밀착시킨 후, 시편마다 각각 다른 3개 부위를 측정하여 색공간 좌표인 L*, a*, b*값을 구하였다.
시편 두께는 0.2mm에서 0, 4mm의 범위로 제작되었으며, 시편을 모형에서 분리하고, 50四의 산화 알루미늄을 2기압 하에서 시편 중앙에서 약 2cm 떨어진 거리에서 20초간 모래분사(sandblast)를 시행하여 시편을 마무리하였다.
시편은 군마다 실제적인 도재 축성의 과정에 따랐으며, 군 별로 거기에 해당되는 과정에 따라 총 4회의 색을 측정하였으며 , 단계별로 군간의 색조 차이를 비교 분석하였다. 1차 색측정은 시편 마무리 직후의 색조를 측정하였고, 2차 색측정은 도재를 축성하기 전의 전처 리 과정 후 축성하였다.
주조 금속시편은 직경 1cm의 주형을 제작한 후 (Fig. 2) 두께 0.4mm의 판형왝스(sheet wax)를사용하여 , 원형 (pattern)을 제작한 후(Fig. 3), 이를 각각 비귀금속군의 경우 매몰재 (fujivestll, GO Co.. Japan)에 제조사의 지시에 따라 분말 대 용액 비가 90:10이 되도록 하여 매몰하였으며, 귀금속군의 경우 같은 매몰재를 사용하여 분말대 용액비가 50:50 이 되게 하여 매몰 하여 , 각각 800도에서 소환, 주조하였다.
대상 데이터
본 연구에 사용된 즉색 색체계는 Chroma Meter CR~200(Minolta Co.Chuo-ku. Osaka, Japan)으로동남아 지역에서 밝은날 오전 11시를 기준으로 하는 광원인 C광원(6774K)를 사용하였다. 색조측정을 위하여 표준백색판으로 영점을 조정한 후, 5mm의 측정경에 시편을 밀착시킨 후, 시편마다 각각 다른 3개 부위를 측정하여 색공간 좌표인 L*, a*, b*값을 구하였다.
본 연구에서는 두 가지의 주조용 합금 구조물과 Gold electroforming system(GAMMAT® free, Gramm Technik Co. Tiefebronn-Muhlhausen, Germany)을 이용한 구조물로 시편을 각각 제작하였으며. 주조용 합금은 다시 귀금속과 비 귀금속, 각 각두 종류의 합금을 사용하였다.
주조용 합금은 다시 귀금속과 비 귀금속, 각 각두 종류의 합금을 사용하였다. 사용된 주조용 합금은 비귀금속으로 Talladium® tilite Ceramic Alloy(Talladium Inc., New York, U.S.A.), 귀금속으로는 금이 함유된 Degudent® H(Degussa~H Is AG., Germany)를 각각 사용하였으며. 순금 시편을 제작하기 위해 금전해질 (Ecolyt SG 100, Gramm Technik Co.
, Germany)를 각각 사용하였으며. 순금 시편을 제작하기 위해 금전해질 (Ecolyt SG 100, Gramm Technik Co. .Tiefebronn-Muhlhausen, Germany) 을 사용하여 이를 GES를 사용하여 제작하였다 (Table 1). 실험에 사용된 도재는 Omega 900 opaque porcelain (Vita Co.
Tiefebronn-Muhlhausen, Germany) 을 사용하여 이를 GES를 사용하여 제작하였다 (Table 1). 실험에 사용된 도재는 Omega 900 opaque porcelain (Vita Co., M chen, Germany)) 을 사용하였으며 , 색조를 객관적으로 측정하기 위한 장치로 Chroma meter CR-200(Minolta Co., Chuo- ku, Osaka, Japan)을 사용하였다(Fig. 1).
Tiefebronn-Muhlhausen, Germany)을 이용한 구조물로 시편을 각각 제작하였으며. 주조용 합금은 다시 귀금속과 비 귀금속, 각 각두 종류의 합금을 사용하였다. 사용된 주조용 합금은 비귀금속으로 Talladium® tilite Ceramic Alloy(Talladium Inc.
데이터처리
15mm in thickness)- and tested color with spectrophotometer every each steps and analyzed with CIEL*a*b* color order system. One-Way ANOVA test was used to find out if there were significant differences between groups tested and Shafife multiple comparison was used to identify where the differences were.
0을 사용하였다. 계측 시기별로 군 간의 L*, a*, b*값을 각각 분산 분석으로 군 간의 유의차가 있는 지 검정하였으며 , 군 간의 유의차가 있는 경우, 사후검정으로 Sheffe 검정을 시행하여, 어느 군에서 유의차가 있는 지를 검정하였으며, 신뢰도는 95% ( P < 0.05)로 설정하였다. 1차 측정 시에는 모든 항목에서 군 간의 유의차가 있었으며, 2 차 측정시에는 L* 수치에 있어서 1군과 2군이 유의차가 없고 나머지 모든 항목에서 유의차가 있었으며 , 3차 측정 시에는 a* 값에 있어서 1군과 2군 및 1 군과 3군에서 유의차가 있고, 나머지 모든 항목에서는 유의차가 없었다.
불투명 도재 (opaque porcelain)는 두 번에 나누어 축성하였으며, 모든 시편의 불투명 도재를 동일한시술자가 도포하였으며, 군 간의 불투명 도재의 동일성을 검정하기 위해, 불투명 도재를 축성 후 l/100mm단위까지 측정이 가능한 전자캘리퍼(digi tal caliper)를 사용하여 시편 당 3회 측정하였으며 (Fig. 7), 분산분석 (one way ANOVA test)을 시행하여 군 간의 유의차가 없음을 검정하였다.
성능/효과
1. 불투명 도재를 도포하기 전, 각 군의 색조를 측정한 결과, 순금인 3군에서 명도와 채도가 가장 높게 나타났으며 비귀금속인 1군이 가장 낮게 나타났다.
2. After application of first opaque porcelain(0.08mm in thickness), after appllication of second opaque porcelain(0.15mm in thickness), pure gold (GES) group showed the least difference in L*, a*, b* values and the lowest AE value(AE=0.63).
2. 순금을 사용한 3군의 경우, 0.08mm의 두께로 불투명 도재를 축성한 3차 측정 시, 높은 채도가 효과적으로 감소되었으■며, 다른 군과 비교해 볼 때 , a*값이 다른 군보다 높게 나타나 4차 측정 시의 값과 가장 유사하였다(』E = 0.63).
3. After application of first opaque porcelain and after application of second opaque porcelain differences that were significant (P< 0.05) between groups were found only in a* values.
3. 불투명 도재를 0.08mm 축성하여 색조를 측정한 결과, L*값과 b*값은 유사하였으나, 적색-녹색의 정도를 의미하는 a* 값은 모두 양의 값을 가져 적색의 경향을 나타냈으며, 순금을 사용한 3군이 가장 높게 나타났다.
없었다. 3차 측정시의 a*값은 3군에서 평균치가 가장 높아 적색의 경향을 가졌으며 , 4차 측정 시에는 1군이 평균치가 가장 높게 나타났다(Table 2).
색조를 표현할 수 있다. 둘째, 치경부는 삭제를 많이 하기가 힘든 경우가 많으며, 특히 치경부에서 얇은 불투명 도재의 축성으로 적색의 성분을 다른 합금에 비해 더욱 많이 지닐 수 있으므로 치경부의 색조 재현이 용이하며, 셋째, 순금의 색조 자체가 치아의 색조계열이며, 적은 두께의 불투명 도 재로 금속의 색조를 차단 할 수 있으므로 치아의 색조 재현이 용이하다고 할 수 있을 것이다.
불투명도 재의 색조 자체는 투명도를 가지고 있지 않으므로두껍게 도포할 수록 불투명도는 증가하며, 이것은 최종 도재의 색조에 투명도를 감소시킴을 알 수 있었다. 또한 금합금 군과 비귀금속 군에 있어서 불투명 도재의 축성 후에 색조의 차이가 나는 것은 Brewer등&의 연구결과와 일치 하였으며, 금합금 군과 순금 군에 있어서는 유의한 차이가 없게 나타났으나, 유의수준 0.01%로 검정하였을 경우에는 유의차가 나타나 금합금과 순금에 있어서도 색조의 차이가 있음을 알 수 있었다.
본 실험에서 불투명 도재를 0.08mm의 두께로 축성한 후 측정한 3차 측정 시의 L* 수치와 불투명 도 재를 0.15mm의 두께로 축성한 후 측정한 4차 측정 시의 L* 수치를 비교해 보았을 때 모든 군에서 수치가 증가하였음을 볼 때, 불투명 도재가 두꺼워 질수록 명도는 증가함을 알 수 있어 , Barghi등®의 연구 결과와 동일하게 나타났음을 알 수 있었다. 불투명도 재의 색조 자체는 투명도를 가지고 있지 않으므로두껍게 도포할 수록 불투명도는 증가하며, 이것은 최종 도재의 색조에 투명도를 감소시킴을 알 수 있었다.
15mm의 두께로 축성한 후 측정한 4차 측정 시의 L* 수치를 비교해 보았을 때 모든 군에서 수치가 증가하였음을 볼 때, 불투명 도재가 두꺼워 질수록 명도는 증가함을 알 수 있어 , Barghi등®의 연구 결과와 동일하게 나타났음을 알 수 있었다. 불투명도 재의 색조 자체는 투명도를 가지고 있지 않으므로두껍게 도포할 수록 불투명도는 증가하며, 이것은 최종 도재의 색조에 투명도를 감소시킴을 알 수 있었다. 또한 금합금 군과 비귀금속 군에 있어서 불투명 도재의 축성 후에 색조의 차이가 나는 것은 Brewer등&의 연구결과와 일치 하였으며, 금합금 군과 순금 군에 있어서는 유의한 차이가 없게 나타났으나, 유의수준 0.
실제적으로 순금의 색상자체는 a*와 b*수치가 합금을 사용한 군보다 높게 나타났는데, 즉 이것은 채도가 높다는 것이며, 또한 Munsell 시스템의 YR의 색조에 해당하는 적색과 황색의 성분을 가지고 있으므로 자연치의 색조공간에 해당되는 색상을 지니며, 자연치의 색상 보다는 채도가 강하다는 것을 알 수 있었다. Lloyd Miller1% 색상, 명도, 채도중 가장조절이 용이한 것은 채도라고 하였으며, 특히 도 재축성을 함에 따라 채도를 떨어뜨리는 것이 더욱 용이하다고 하였다.
연구실험의 결과에서 순금을 사용한 3군의 경우 불투명 도재를 1회 도포한 색조와 2회도포한 색조의 차이가 가장 적게 나타났으며, 색차 방정식을 이용한 색조의 차이값은 0.63으로 미국치과의사 협회에서 기준값으로 규정하는29, 수치인 2 보다는 작은 색의 차이가 존재하였지만, Goldstein등2® 은』E 의 차이가 0.4이상만 되어도 색의 구별이 가능하다고 하였으므로 다른 군에 비하여 색차가 적다고 할 수 있었으며, 1회 도포만으로도 임상적으로는 무시할 만큼의 색차를 가짐을 알 수 있어, 적은 두께의 불투명 도재로도 금속의 색을 차단할 수 있다고 말할 수 있을 것이다.
GES는 99%의 순금을 사용하며 매우 정밀한 적합성을 가지는 고정성 보철물 및 텔레스코픽 (telescopic) 의치를 제작할 수 있다. 이 시스템은 0.2mm의 균일한 두께를 가지며, 평균 19㎛의 marginal gap을 가지는 하부구조물 (coping)을 제작할 수 있으며, 순금을 사용하므로알러지 반응이나, 지난 몇 년간 당면해 온 니켈, 베릴륨, 팔라듐과 같은 금속을 포함한 금속과 관련된 인체 유해작용을 가져오는 잠재성을 감소시켰다. GES 수복물은 삭제량이 최소한이더라도 심미적인 수복 물을 제작할 수 있는 잠재성을 가지고 있으며, 하부구조물의 순금의 색상은 불투명 도재에 의해 좀 더 쉽게 차단되며, 더 나은 색의 깊이를 가지게 된다.
이상과 같이, 순금을 사용할 경우 얇은 두께의 불투명 도재로 금속의 색을 차단할 수 있었으며, 이것은 최종 도재 수복물의 색조에 긍정적인 영향을 미칠 것으로 생각되었다.
즉, 3군-2군-1군의 순서로 채도가 높았으나, 불투명 도재의 두께가 증가하면서 채도의 차이는 감소하였다.
후속연구
그러므로 하부구조물을 얇게 제작할 수 있는 GES의 경우 도재를 두껍게 축성하는 것이 가능하므로 색조의 깊이를 부여하고 정확한 색조의 재현을 가능하게 할 수 있을 것이다. 또한 불투명 도 재를 최소한으로 사용하여 금속의 색을 균일하게 차단할 수 있다면 도재의 색조에 긍정적인 영향을 미칠 것이다.
심미성을 평가하기는 어렵다. 불투명 도재가 금속의 색을 어느 정도 차단하며, 최종도재의 심미성에 어떠한 영향을 미치는 가에 대한 객관적 연구뿐만 아니라 동일한 조건 하에서 최종도재의 색조가 심미성에 있어서 어떻게 영향을 받는지에 대한 주관적인 연구 또한 필요하며, 앞으로 이에 대한 연구가 필요하다고 생각되었다.
참고문헌 (29)
Campbell, S.D. A comparative study of metal ceramic and all ceramic esthetic materials : Modulus of rupture. J Prosthet Dent 1989;62:476
Crispin, B.J., Jo, Y.H., and Hobo. S. Esthetic ceramic restorative materials and techniques In Contemporary esthetic dentistry : practice fundamentals (Crispin,B.J. eds.). Quintessence Publishing Co,. Chicago 1994:155-188
Karl F. Leinfelder. Porcelain esthetics for the 21st century. J American dental association 2000;131:47s-51s
Chae YA. A Study of Ni-rosistant bacteria isolated from gingival crevicular fluid on the patients wearing Ni-Cr alloy prosthesis (In terms od molecular biological aspects) : Article, Dept. of Dentistry, Kyung-Hee Univ. 1999
Rogers O. W., and Armstrong B. W. Electroforming a Gold Matrix for Indirect Inlays. J Prosthet Dent 1961;11:959-966
Flemming Behrend. Gold Electroforming System : GES Restorations. J. Dent. Tech 1997;Mar:31-37
Lecardonnel A. Sunrise Gold Foil Jacket Crown. Cashiers de Prosthese 1989;67:62-68
J.D Brewer., J.S.Glennon. and D.A.Garlapo. Spectrophotometic analysis of a nongreening, metal-fusing porcelain. J Prosthet Dent. 1991:65(5):634-641
S.H. Jacobs., C.J. Goodcre., B.K. Moore. and R.W. Dykema. Effect of porcelain thickness and type of metal-ceramic alloy on color. J Prosthet Dent 1987;57:138-145
Seghi R. R., Johnston W. M. and O'Brien W.J. Spectrophotometric analysis of color differences between porcelain systems. J Prosthet Dent 1986;56(1):35-40
Peter. S. Lund., Steven. A. Aquilino., and Donna. L. Dixon. Evaluation of the color and appearance of a new textured opaque porcelain. Int J Prosthodontics 1991;4:548-554
Youn SS. Lee SH, Yang JH, Chung BY. A study on the color change of ceramic by PdAg alloy and mechanism. J Korean Acad prosthodont 1989;27:1
Bangtson L.K. and Goodkind R.J. The conversion of chromascan designation to ClE tristimulus values. J Prosthet Dent 1982;47:610-617
Kim YH, Study on the color staility of veneer resin. J Korean Acad Conservative Dentistry 1991;16:1-5
Jin TH, Cho HW and Jung lY. The influence of contamination on the porcelain color . WonKwang Dentistry 1991;2:161-170
Vander Burgt. et al. Report of the committee on scientic investigation of the American academy of restorative dentistry. J Prosthet Dent 1991;66:84-122
Seghi, R. R., Johnston W.M., and O'Brien, W.J. Performance assessment of colorimetric devices on dental porcelains. J Dent Res 1989;68(12):1755-1759
Seghi, R. R., Hewlett, E.R., and Kim, J. Visual and instrumental colorimetric assessments of small color differences on transluscent dental porcelain. J Dent Res 1989;68(12):1760-1764
O'Brien,W.J., Groh, C.L., and Boenke, K. M. A new, small-color-difference equation for dental shades. J Dent Res 1990:69(11):1762-1764
Goldstein, G.R., and Schmitt, G.W. Repeatability of a specially designed intraoral colorimeter. J Prosthet Dent 1993:69:616-619
※ AI-Helper는 부적절한 답변을 할 수 있습니다.