[국내논문]중진지역에 적합한 액상화 평가 생략기준 및 지진규모 보정계수에 관한 연구 A Study on Magnitude Scaling Factors and Screening Limits of Liquefaction Potential Assessment in Moderate Earthquake Regions원문보기
기존의 액상화 평가법은 대부분 미국, 일본, 그리고 유럽과 같이 지진 발생빈도가 높고 그로 인한 액상화 피해가 빈번한 국가에서 주도적으로 연구되어왔다. 이런 지역적 특성을 토대로 개발된 액상화 평가방법들은 높은 지진규모(M=7.5)에 바탕을 두고 있다. 국내의 경우, 1997년 실제적인 내진 연구가 시작된 이래 액상화 평가의 구체적 규정은 항만시설의 내진설계 표준서(1999)에 언급된 바 있으나 이는 문헌연구를 통해 제시된 것으로 실제적이지 못하다. 그러므로, 국내 적합한 설계기준을 작성하기 위해서는 지진피해자료의 부족을 국내 지반을 대상으로 한 동적실내시험을 통하는 것이 바람직하며, 일반적인 정현하중 진동시험 보다 실제 지진하중 재하 시험이 훨씬 효과적일 수 있다. 본 연구에서는 실제 지진파 고유의 특성을 적용한 진동삼축 시험을 통하여 상대밀도와 세립분함유량의 변화에 따른 액상화 저항강도를 산정하였다. 실험결과를 국내의 대표적인 항만지역의 지진응답 해석 결과와 비교 분석하고 중진지역에 적합한 액상화 평가의 생략기준을 제시하였다. 또한 실제 지진하중 삼축실험 결과를 이용하여 국내 여건에 적합한 지진규모 보정계수를 제안하였다.
기존의 액상화 평가법은 대부분 미국, 일본, 그리고 유럽과 같이 지진 발생빈도가 높고 그로 인한 액상화 피해가 빈번한 국가에서 주도적으로 연구되어왔다. 이런 지역적 특성을 토대로 개발된 액상화 평가방법들은 높은 지진규모(M=7.5)에 바탕을 두고 있다. 국내의 경우, 1997년 실제적인 내진 연구가 시작된 이래 액상화 평가의 구체적 규정은 항만시설의 내진설계 표준서(1999)에 언급된 바 있으나 이는 문헌연구를 통해 제시된 것으로 실제적이지 못하다. 그러므로, 국내 적합한 설계기준을 작성하기 위해서는 지진피해자료의 부족을 국내 지반을 대상으로 한 동적실내시험을 통하는 것이 바람직하며, 일반적인 정현하중 진동시험 보다 실제 지진하중 재하 시험이 훨씬 효과적일 수 있다. 본 연구에서는 실제 지진파 고유의 특성을 적용한 진동삼축 시험을 통하여 상대밀도와 세립분함유량의 변화에 따른 액상화 저항강도를 산정하였다. 실험결과를 국내의 대표적인 항만지역의 지진응답 해석 결과와 비교 분석하고 중진지역에 적합한 액상화 평가의 생략기준을 제시하였다. 또한 실제 지진하중 삼축실험 결과를 이용하여 국내 여건에 적합한 지진규모 보정계수를 제안하였다.
Conventional methods for the assessment of liquefaction potential were primarily for areas of severe earthquake zones (M=7.5) such as North America and Japan. Detailed earthquake related researches in Korea started in 1997, including development of the seismic design standards for port and harbour s...
Conventional methods for the assessment of liquefaction potential were primarily for areas of severe earthquake zones (M=7.5) such as North America and Japan. Detailed earthquake related researches in Korea started in 1997, including development of the seismic design standards for port and harbour structures, which was later completed in 1999. Because most contents in the guidelines were quoted through literature reviews from North America and Japan, which are located in strong earthquake region, those are not proper in Korea, a moderate earthquake region. This requires further improvement of the present guidelines. Considering earthquake hazard data in Korea, use of laboratory tests based on irregular earthquake motion appears to be effective to reflect the dynamic characteristics of soil more realistically than those using simplified regular loading. In this study, cyclic triaxial tests using irregular earthquake motions are performed with different earthquake magnitudes, relative densities, and fines contents. Assessment of liquefaction potential in moderate earthquake regions is discussed based on various laboratory test results. Effects of these components on dynamic behavior of soils are discussed as well. From the test results, screening limits and magnitude scaling factors to determine the soil liquefaction resistance strength in seismic design were re-investigated and proposed using normalized maximum stress ratios under real irregular earthquake motions.
Conventional methods for the assessment of liquefaction potential were primarily for areas of severe earthquake zones (M=7.5) such as North America and Japan. Detailed earthquake related researches in Korea started in 1997, including development of the seismic design standards for port and harbour structures, which was later completed in 1999. Because most contents in the guidelines were quoted through literature reviews from North America and Japan, which are located in strong earthquake region, those are not proper in Korea, a moderate earthquake region. This requires further improvement of the present guidelines. Considering earthquake hazard data in Korea, use of laboratory tests based on irregular earthquake motion appears to be effective to reflect the dynamic characteristics of soil more realistically than those using simplified regular loading. In this study, cyclic triaxial tests using irregular earthquake motions are performed with different earthquake magnitudes, relative densities, and fines contents. Assessment of liquefaction potential in moderate earthquake regions is discussed based on various laboratory test results. Effects of these components on dynamic behavior of soils are discussed as well. From the test results, screening limits and magnitude scaling factors to determine the soil liquefaction resistance strength in seismic design were re-investigated and proposed using normalized maximum stress ratios under real irregular earthquake motions.
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
가설 설정
(2) Proposed MSFs were lower than those recommended from the NCEER workshop. But, proposed MSF obtained in this study is 1.
제안 방법
In order to compare liquefaction resistances between irregular earthquake and equivalent sinusoidal cyclic loadings, additional tests were performed. Jumunjin sand samples with no fines were tested under confining pressure of 100 kPa and relative density of 60%.
Effects of fines content and relative density were also analyzed based on cyclic triaxial test results under real irregular earthquake motions. In particular, a series of cyclic tests under various soil conditions were carried out expecting to be used for future modification of the Korean seismic design standards in two aspects: criteria for screening limits and MSFs of liquefaction analysis. The final goal of this paper is to propose MSFs and to evaluate criteria for the earthquake screening limits under which detailed liquefoction analysis could be omitted in a design process.
If a denser sample is to be prepared, compaction energy is applied by hitting the side of the mold stepwise during the process of sample placement. In this study, densification of the sample was accomplished by carefully and symmetrically tapping the sides of the sample mold immediately after soil deposition. Because the mass of sand and silt used in sample preparation could be accurately estimated, it was possible to obtain a relative density that was reasonably close to a target value by measuring the height of the sample as it densifies.
Because MSFs and screening limits currently available are primarily for earthquakes with large magnitudes and clean sands, uncertainties still exist for moderate earthquake areas and silty sand deposits. In this study, laboratoiy cyclic tests using both regular sinusoidal and irregular earthquake loadings were performed and compared. Effects of fines content and relative density were also analyzed based on cyclic triaxial test results under real irregular earthquake motions.
The maximum possible frequency allowed in the system is 70 Hz. Measurements in the tests include axial deformations, volume changes, deviatoric stresses, and pore water pressures with time. Triaxial tests under sinusoidal loading were also carried out for the comparison of results between irregular earthquake and regular sinusoidal loadings.
Soils used in cyclic triaxial tests were the Jumunjin sand, a representative silica sand in Korea, with four different fines contents equal to 0, 10, 20, and 30%. Tests with clean sand samples (i.
Soils used in cyclic triaxial tests were the Jumunjin sand, a representative silica sand in Korea, with four different fines contents equal to 0, 10, 20, and 30%. Tests with clean sand samples (i.e., fines content of 0%) were used for investigation of MSF while criteria for liquefaction screening limits were analyzed using both clean and silty sand samples of fines contents equal to 0, 10, 20, and 30%. The silty sands were prepared by mixing regular Jumunjin sands and silt-sized crushed Jumunjin sands at desired weight ratios.
In particular, a series of cyclic tests under various soil conditions were carried out expecting to be used for future modification of the Korean seismic design standards in two aspects: criteria for screening limits and MSFs of liquefaction analysis. The final goal of this paper is to propose MSFs and to evaluate criteria for the earthquake screening limits under which detailed liquefoction analysis could be omitted in a design process.
To revise the present Korean seismic standards for the liquefaction potential assessment, cyclic triaxial tests using irregular earthquake motions, different earthquake magnitudes, relative densities, and fines contents were performed. The following primary conclusions are obtained as a result of this study:
Measurements in the tests include axial deformations, volume changes, deviatoric stresses, and pore water pressures with time. Triaxial tests under sinusoidal loading were also carried out for the comparison of results between irregular earthquake and regular sinusoidal loadings. For these tests with sinusoidal loadings, Jumunjin sands with no fines were used.
이론/모형
5 for earthquake-related design without detailed specification of MSFs. In this study, MSFs were re-investigated based on laboratory cyclic triaxial test results given in Fig. 8 using method derived by Seed and Idriss (1982). To propose MSFs in this study, the amplitudes of the applied loading, as quantified by maximum stress ratio, were determined as a function of the earthquake magnitudes required causing liquefaction in Fig.
Basic property tests were performed for each test soil, and results are shown in Table 1. The maximum and minimum index densities (i.e., minimum and maximum index void ratios) of soils with different fines contents were determined by the procedure specified in ASTM-4253 vibratoiy table and ASTM-4254 method B, respectively.
6 were selected as input motions for considering moderate earthquake magnitudes in Korea. The seismic demand can be determined for a soil profile at any desired depth based on results of maximum acceleration and stresses using the SHAKE91 analysis. In the SHAKE91 analysis, all the earthquake input motions with peak acceleration level of 0.
성능/효과
(3) Triaxial Tests were carried at conditions of different relative densities (60, 70, and 75%) and fines contents (0, 10, 20, and 30%). In the test results for both clean and silty sands, effects of the relative density appear to be significant representing higher liquefaction resistances with increasing relative densities. It is also observed that the liquefaction resistance of silty sands increases with increasing fines contents.
후속연구
It is also found that soils of a relative density equal to 70% with a fines content of 20% represents a similar condition mentioned above. Although additional investigations are needed, results obtained in this study can be used for further development of the liquefaction screening limits in Korea.
참고문헌 (26)
Abrahamson, N. and Silva, W. (1996), Empirical ground motion models, draft Report. Brookhaven National Laboratory
Ambraseys, N. N. (1988), 'Engineering seismology', Earthquake Engrg. and Struct. Dyn., Vol.17, No.1, pp.1-105
Andrus, R. D. and Stokoe, K. H., Il. (1997), 'Liquefaction resistance based on shear wave velocity', Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, T. L. Youd and I. M. Idriss, eds., National Center for Earthquake Engineering Research, Buffalo, N. Y., pp.89-128
Arango, I. (1996), 'Magnitude scaling factors for soil liquefaction evaluations', J. Geotech. Engrg., ASCE, Vol.122, No.11, pp.929-936
ASTM D 4254. (1991), 'Standard test methods for minimum index density and unit weight of soils and calculation of relative density', American Society of Testing and Materials, West Conshohocken, Pennsylvania, USA
ASTM D 4253. (1993), 'Standard test methods for maximum index density and unit weight of soils using a vibratory table', American Society ofTesting and Materials, West Conshohocken, Pennsylvania, USA
Chang, N. Y., Yeh, S. T., and Kaufinan, L. P. (1982), 'Liquefaction potential of clean and silty sands', Proc.. 3rd Int. Earthquake Microzonation Corf., Vol.2, pp.1017-1032
Dezfulian H. (1982), 'Effects of silt content on dynamic properties of sandy soils', Proc., 8th World Conf. on Earthquake Engrg., pp.63-70
Dobry, R. (1991), 'Soil properties and earthquake ground response', Proceedings of the 10th European Conference on Soil Mechanics and Foundation Engineering, Florence, Italy, Vol.4
Earthquake engineering society of Korea (1999), Seismic design standard for port and harbour structures, Ministry of maritime affairs and fisheries (in Korean)
Idriss, I. M. (1999), 'An update to the Seedldriss simplified procedure for evaluating liquefaction potential', Presentation notes, Workshop new approaches to liquefaction analysis, Transportation Research Board, Washington, D. C.
Idriss, I. M. and Sun, J. I. (1992), Users Manual for SHAKE91, Department of Civil and Environmental Engineering, Univ. California, Davis
Kim, S. I. (1998), 'Assessment and remediation for liquefaction in Korea', Proc.. KGS Fall 1998 Nat. Conf., pp.3-30
Liu, A H. Stewart, J. P., Abrahamson, N. A, and Moriwaki, Y. (2001), 'Equivalent number of uniform stress cycles for soil liquefaction analysis', J. Geotech. Engrg., ASCE, Vol.127, No.12, pp.1017-1026
Mulilis, J. P. (1975), The effects of method of sample preparation on the cyclic stress strain behavior of sands. EERC Report 7518, College of Engineering, University of California, Berkeley, July
Polito, C. P. and Martin II, J. R. (2001), 'Effects of nonplastic fines on the liquefaction resistance of sands', J Geotech. and Geoenviron Engng. Vol.127, No.5, pp.408-415
Schnabel, P. B., Lysmer, J., and Seed, H. B. (1972), A computer program for earthquake response analysis of horizontally layered sites. Report no. EERC 7212, Earthquake Engineering Research Center, Univ. California, Berkeley
Seed, H. B. and Idriss, I. M. (1982), Ground motions and soil liquefaction during earthquakes. Earthquake Engrg. Res. Inst., Oaklanc, California
Seed, H. B., Idriss, I. M., Makdisi, F., and Banerjee, N. (1975), Representation of Irregular Stress Time Histories by Equivalent Uniform Stress Series in Liquefaction Analysis. Report No. EERC 7529, UCB
Seed, R. B., Cetin, K. O., Mossw, R. E. S., Kammerer, A. M., Wu, J., Pestana, J. M., Riemer, M. F., Sancio, R. B., Bray, J. D., Kayen, R. E., and Faris, A. (2003), Recent advances in soil liquefaction engineering: A unified and consistent framework. Report No. EERC 2003-06, UCB
Tsuchida, H. (1970), 'Prediction and remedial measures against liquefaction of sandy soil', Annual Seminar of Port and Harbor Research Institute: Vol.3, pp.1-33 (in Japanese)
Vaid Y. P. and Sivathayalan S. (1996), 'Static and cyclic lique-faction potential of Fraser Delta sand in simple shear and triaxial tests', Canadian Geotechnical Journal, Vol.33, pp.281-289
Youd, T. L., and Idriss, I. M., eds. (1997), Proc., NCEER Workshop on Evaluation of Liquefaction Resistance of Soils, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York at Buffalo
Youd, T. L. and Noble, S. K. (1997), 'Magnitude scaling factors', Proc., NCEER Workshop on Evaluation ofLiquefaction Resistance of Soils, T. L. Youd, and M. Idriss, eds., National Center for Earthquake Engineering Research, Buffalo, N. Y., pp.149-165
Youd, T. L., Idriss, I. M., Andrus, R. D., Arango, I., Castro, G., Christian, J. T., Dobry, R., Finn, W. D. L., Harder, L. F., Hynes, M. E., Ishihara, K., Koester, J. P., Liao, S. S. C., Marcuson IIl, W. F., Martin, G. R., Mitchell, J. K., Moriwaki, Y., Power, M. S., Robertson, P. K., Seed, R. B., and Stokoe II, K. H. (2001), 'Liquefaction resistance of soils : Summary report from the 1996 NCEER and 1998 NCEER/NSF workshops on evaluation of liquefaction resistance of Soils', J. Geotech Engrg., ASCE, Vol.127, No.10, pp.817-833???????????????????????????????????렙???렙????????볪??車?攀攀????볪??????倚??????????????렁??????돐????잖???????덐?????????돀???????????????뤏?돐?잖????????돀??????????瀁??????돐送?????잖?頁??????덐?????쀋??慤????牡?????印楮??慶敲湯??湧楯?????????畢?慣?????牲??
※ AI-Helper는 부적절한 답변을 할 수 있습니다.