We synthesized two new series of alternating copolymers, poly[bis(2-(4-phenylenevinylene)-2-cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-1,4-phenylene](Polymer-I)and poly[bis(2-(4-phenylenevinylene)-2cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-2,7-(9,9-dihexylfluorene)](Polymer-II), via the ...
We synthesized two new series of alternating copolymers, poly[bis(2-(4-phenylenevinylene)-2-cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-1,4-phenylene](Polymer-I)and poly[bis(2-(4-phenylenevinylene)-2cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-2,7-(9,9-dihexylfluorene)](Polymer-II), via the Suzuki coupling reaction, for use in light-emitting diodes (LEDs). Defect-free uniformly thin films of these polymers were found to be easily formed on indium-tin oxide (ITO) coated glass substrates. Multi-layer LEDs with ITO/PEDOT/Polymer/ LiF/Al configurations with or without an $Alq_3$ electron transport layer were fabricated with these polymers. The maximum EL emissions of Polymer-I and Polymer-II with an $Alq_3/LiF/Al$ cathode were observed at 516 and 533 nm, respectively. The maximum brightness and external luminance efficiency of the devices fabricated with the EL polymers were found to be $411 cd/m^2$ and 0.16 cd/A, respectively.
We synthesized two new series of alternating copolymers, poly[bis(2-(4-phenylenevinylene)-2-cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-1,4-phenylene](Polymer-I)and poly[bis(2-(4-phenylenevinylene)-2cyanoethenyl)-9,9-dihexyl-9H-fluoren-2,7-yl-alt-2,7-(9,9-dihexylfluorene)](Polymer-II), via the Suzuki coupling reaction, for use in light-emitting diodes (LEDs). Defect-free uniformly thin films of these polymers were found to be easily formed on indium-tin oxide (ITO) coated glass substrates. Multi-layer LEDs with ITO/PEDOT/Polymer/ LiF/Al configurations with or without an $Alq_3$ electron transport layer were fabricated with these polymers. The maximum EL emissions of Polymer-I and Polymer-II with an $Alq_3/LiF/Al$ cathode were observed at 516 and 533 nm, respectively. The maximum brightness and external luminance efficiency of the devices fabricated with the EL polymers were found to be $411 cd/m^2$ and 0.16 cd/A, respectively.
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
제안 방법
Emission spectra of dilute (~10-6M) solutions of the polymers were recorded on a Perkin-Elmer LS-50 fluorometer utilizing a lock-in amplifier system with a chopping frequency of 150 Hz. Solid-state emission measurements were carried out using films supported on glass substrates and mounted with front-face excitation at an angle of < 45°;. Each polymer film was excited with several portions of visible light from a xenon lamp.
Alq3, LiF, and aluminum metal were deposited on top of the polymer films through a mask by vacuum evaporation at pressures below 1 X 10-6 torr, yielding active areas of 4 mm2. To determine the device characteristics, the current density-voltage-luminescence (J-V-L) changes were measured using a current/voltage source (Keithley 238) and an optical power meter (CS-1000, LS-100). All procedures and measurements described above were carried out in the open air at room temperature.
We fabricated multi-layer PLEDs with the ITO/PEDOT/Polymer/cathode configurations using two types of cathode structures. The cathodes were fabricated with a LiF(1 nm)/Al(200 nm) bilayer(device 1) or a triple layer of Alq3(20 nm)/LiF(1 nm)/Al (200 nm)(device 2).
참고문헌 (27)
C. W. Tang and S. A. VanSlyke, Appl. Lett., 51, 913 (1987)
S. A. VanSlyke, P. S. Bryan, and C. W. Tang, Proceedings of the 8th International Workshop on Inorganic and Organic Electroluminescence, Berlin, Germany, 1996, pp 195
J. Kido, H. Shionoya, and K. Nagai, Appl. Phys. Lett., 67, 2281 (1995)
※ AI-Helper는 부적절한 답변을 할 수 있습니다.