최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기한국기계가공학회지 = Journal of the Korean Society of Manufacturing Process Engineers, v.17 no.2, 2018년, pp.68 - 76
최훈기 (국립창원대학교 기계공학부) , 유근종 (국립창원대학교 기계공학부) , 임윤승 (국립창원대학교 기계공학부)
A vortex tube is a simple energy separating device that splits a compressed air stream into a cold and hot stream without any external energy supply or chemical reactions. The efforts of many researchers and designers have been focused on improvement of vortex tube efficiency by changing the paramet...
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
핵심어 | 질문 | 논문에서 추출한 답변 |
---|---|---|
보텍스튜브는 무엇인가? | 냉풍발생장치는 중, 소량인 경우 보텍스튜브(Vortex Tube)를 사용할 수 있다. 이러한 보텍스튜브는 압축된 가스를 챔버 내부로 유입시키면 어떠한 움직이는 기구도 없고 튜브내부에서 화학반응도 없이 입구로 유입되는 가스보다 저온의 공기를 얻을 수 있는 디바이스이다. 상온의 공기를 압축하여 보텍스튜브에 유입시키면 온풍과 냉풍으로 분리되어진다. | |
절삭가공에서 절삭유를 사용하는 이유는? | 절삭가공에서 최적의 가공조건 [1] 은 절삭성능에 큰 영향을 끼치게 된다. 절삭가공에서 칩의 원활한 배출, 공작물 또는 공구의 냉각, 공구와 칩 사이의 윤활, 가공된 공작물의 표면 거칠기의 확보를 위하여 절삭유를 일반적으로 사용한다. 이러한 절삭유는 성능향상을 위하여 염소, 황, 인등 유독물질이 첨가제로 포함되어 있어 환경적인 문제뿐만 아니라 절삭유와 설비유지관리에 필요한 절삭유 관련 비용이 많이 소요되고 있는 실정이다. | |
절삭가공 중 세미 건식가공의 장점은? | 냉각공기와 압축공기에 미량의 윤활유를 동시에 공급하는 세미 건식가공방법은 건식 가공보다 윤활작용 및 냉각성능을 보다 개선할 수있는 방법이다. 이러한 세미 건식가공은 일반적인 절삭보다는 훨씬 적은 소량의 윤활유로 냉각 및 윤활성능을 확보할 수 있으므로 보다 친환경적인 가공 [3] 을 실현할 수 있는 장점을 가진다. Fig. |
Kim, J. S., Lee, D. S., Wang, D. H., "Development of Coolant/Waste-oil Separating and Cooling System with Chip Treatment," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 3, pp. 16-23, 2017.
Chang, Y.S., Kim, S.T., "Evaluation of the Economic of High Speed Machining Considering Environment Effects," Clean Technology, Vol.12, pp.182-1899, 2006.
Marshall, J., "Effect of Operating Conditions, Physical Size and Fluid Characteristics on the Gas Separation Performance of a Linderstrom-Lang Vortex Tube," Int. J. Heat Mass Transfer, Vol.20, pp.227-231, 1977.
Fulton, C.D., "Ranque's Tube," J. ASRE Refrigerating Eng., Vol.58, pp.473-479, 1950.
Alimov, R.Z., "Flow Friction and Heat and Mass Transfer in a Swirled Flow," Journal of Engineering Physics and Thermophysics, Vol.10, No.4, pp.251-257,1966.
Ahlborn, B. and Groves S., "Secondary Flow in a Vortex Tube," Fluid Dynamics Research, Vol.21, pp.73-86, 1997.
Kurosaka, M., "Acoustic Streaming in Swirling Flow and the Ranque-Hilsch (Vortex-Tube) Effect," J. Fluid Mech., Vol.124, pp.139-172, 1982.
Xue Y., Arjomandi, M., and Kelso, R. "A Critical Review of Temperature Separation in a Vortex Tube," Exper. Therm. Fluid. Sci., Vol.34, pp.1367, 2010.
Westley, R., "Optimum Design of a Vortex Tube for Achieving Larger Temperature Drop Ratios," Cranfield College Note 30, College of Aeronautics, 1955.
Ting-Quan, M., Qing-Guo, Z. H. A. O., Jian, Y., Fang, Y., Chong-Fang, M. "Experimental Investigation on Energy Separation by Vortex Tubes," In 12th International Heat Transfer Conference. Grenoble, 2002.
Marques, C. H., Isoldi, L. A., Santos, E. D. D., Rocha, L. A. O., "Constructal Design of a Vortex Tube for Several Inlet Stagnation Pressures," Thermal Engineering, Vol.11, pp.85-92, 2012.
Gadhave, A. S., Kore, S. S. "An Experimental Study on Operating Parameter on Counter flow Vortex Tube," International Journal of Innovative Science, Engineering & Technology, Vol.2, pp.401-405, 2015.
Skye, H. M., Nellis, G. F., Klein, S. A. "Comparison of CFD Analysis to Empirical Data in a Commercial Vortex Tube," International Journal of Refrigeration, Vol. 29, No. 1, pp.71-80, 2006.
Secchiaroli, A., Ricci, R., Montelpare, S. D'Alessandro, V., "Numerical Simulation of Turbulent Flow in a Ranque-Hilsch Vortex Tube," International Journal of Heat and Mass Transfer, Vol.52, pp.5496-5511, 2009.
Fluent, "ANSYS Fluent V.18 User Guide", USA, 2018.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.