[논문]3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성

김지원; 구본열

doi:10.17946/jrst.2023.46.6.485

[국내논문] 3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성
Usefulness of an Auxiliary Tool for Hand Radiography by Using 3D Printing 원문보기

방사선기술과학 = Journal of radiological science and technology, v.46 no.6, 2023년, pp.485 - 491

김지원 (대전보건대학교 방사선의과학대학 방사선과) , 구본열 (전주비전대학교 방사선과)

Abstract ▼ AI-Helper

As an auxiliary tool for fixing the patient's posture when taking an X-ray, sponges with high radiolucencies are laminated in various thicknesses. This study aimed to evaluate the usefulness of an auxiliary tool for hand oblique projection X-ray by manufacturing it with a uniform thickness by 3D printing and comparing it with existing sponge tools. In the auxiliary tool, radiolucency was measured at the stairs where each finger was located, and pixel information values were compared in the digital imaging and communications in medicine(DICOM) image. Contrast to noise ratio(CNR) and signal to noise ratio(SNR) were compared by shooting the hand phantom and the auxiliary tool together. As the thickness of the sponge tool increased, radiolucency decreased by 15.52% and pixel information value increased by 20.61%. The transmittance of the 3D printing tool increased by 0.82%, and the pixel information value differed by 5.66%. CNR and SNR increased by 20.03% and 22.42% in 3D printing compared to existing sponge tools. while taking hand oblique projection, maintaining the thickness of the auxiliary tool uniformly through 3D printing maintains high radiolucency and minimal impact on medical images, and increases CNR and SNR, making it useful as an auxiliary tool for taking hand oblique projection.

주제어

참고문헌 (18)

Korean Society of Medical Imaging Technology.？Textbook of radiographic positioning and clinical？diagnosis. 6th ed. Vol. 1. Chung-Ku Publisher;？2019:76-8.？
Lim WT, Hong DH. Development of the upper wear？fixation device for chest ap x-ray imaging on the？emergency stretcher bed. Journal of Radiological？Science and Technology. 2022;45(3):205-11. DOI:？https://doi.org/10.17946/JRST.2022.45.3.205？

원문보기 상세보기
Uhm SY, Cho YK, Kang SJ. A study on the accuracy？and convenience of imaging method using support？device in knee joint lateral radiography. Journal of？the Korean Society of Radiology. 2017;11(4):253-62.？DOI: https://doi.org/10.7742/jksr.2017.11.4.253？

원문보기 상세보기
Rhee DB, Seo SJ, Choi HW, Lee SH, Kim JK.？Development and use of supporting device for patellar？x-ray imaging. Journal of Biomedical Engineering？Research. 2020;41(4):165-71. DOI: https://doi.org/10.9718/JBER.2020.41.4.165？

원문보기 상세보기
Rhee DB, Lee SM, Kim JK, Lee JM. A study on chest？x-ray using ancillary device for child radiography.？Journal of Biomedical Engineering Research. 2018;39(1):48-54. DOI: https://doi.org/10.9718/JBER.2018.39.1.48？

원문보기 상세보기
Choi OR, Jang WS, Jung PS, Lee YS, Lee KS.？Evaluation of usefulness of the device when taking？a wrist lateral radial tilt view. Journal of Korean？Society of Radiologocal Imaging Technology. 2014;2014(1):1-8. Retrieved from https://ebook.kyobobook.co.kr/dig/pnd/scholardetail/product?cmdtcode4010025912754？
Park JK, Yang SW, JunJH, Cho SY, Kim KT, Heo？YJ, et al. The effects of image quality due to scattering x-ray according to increasing patient thickness.？Journal of the Korean Society of Radiology. 2017;11(7):670-7. DOI: https://doi.org/10.7742/jksr.2017.11.7.671？

원문보기 상세보기
Seo JH, Jeong JH, Shin JH, Won JH, Jung SW, Ha？SY, et al. Investigation of scattered radiation on？images effect in digital radiography. Journal of the？Korean Society of Radiology. 2014;8(1):77-9. Retrieved？from https://ebook.kyobobook.co.kr/dig/pnd/scholardetail/product?cmdtcode4010023818063？
Chang JH, Yang EJ, Kim YJ. A study on the distribution？of microorganisms in department of radiography.？Journal of the Korean Society of Radiology. 2021;15(2):165-71. DOI: https://doi.org/10.7742/jksr.2021.15.2.165？

원문보기 상세보기
Hong DH, Kim HG. Analysis of bacterial contamination on surface of general radiography？equipment and CT equipment in emergency room？of radiology. Journal of Radiological Science and？Technology. 2016;39(3):421-7. DOI: https://doi.org/10.17946/JRST.2016.39.3.17？

원문보기 상세보기
Kim SH. Study on 3D printer producing of assistive？devices for vertical incidence of law method. Journal？of Radiological Science and Technology. 2020;43(6):489-94. DOI: https://doi.org/10.17946/JRST.2020.43.6.489？

원문보기 상세보기
Kim HG. Evaluation of the clinical usefulness of？an assistive device fabricated by 3D printing in an？oblique x-ray examination of the lumbar vertebrae.？Journal of the Korean Society of Radiology. 2022;16(5):505-12. DOI: https://doi.org/10.7742/jksr.2022.16.5.505？

원문보기 상세보기
Kim HG, Yoon JH, Choi SD. Study on 3D printer？production of auxiliary device for upper limb for？medical imaging test. Journal of Radiological？Science and Technology. 2015;38(4):389-94. DOI:？https://doi.org/10.17946/JRST.2015.38.4.08？

원문보기 상세보기
Yoon MS, Han DK, Sin RW, Han SS, Yang YJ, In？YJ, et al. The study of making an assistance device？in hand lateral examination using 3D printer. Journal？of the Korean Society of Radiological Imageing？Technology. 2018;2018(1):119-23. Retrieved from？https://ebook.kyobobook.co.kr/dig/pnd/scholardetail/product?cmdtcode4010026498868？
Cho YI. Feasibility of the 3D printing materials for？radiation dose reduction in interventional radiology.？Journal of Radiological Science and Technology.？2020;43(3):169-76. DOI: https://doi.org/10.17946/JRST.2020.43.3.169？

원문보기 상세보기
Yoon J, Yoon MS. Evaluation of tungsten blended？filament shields made by 3D printer in radiography.？Journal of Radiological Science and Technology.？2021;44(6):615-21. DOI: https://doi.org/10.17946/JRST.2021.44.6.615？

원문보기 상세보기
Kim KM. Utilization of 3D printing technology in？the mold industry used in shipbuilding, energy,？heavy industry and automobiles. Industry News？[Internet]. 2020 [cited 2023 Oct 6]. Retrieved from？https://www.industrynews.co.kr/news/articleView.html?idxno39065？
Moon JH, Koo BY. Usefulness of carbon fiber reinforced plastics as a material of auxiliary tool for？x-ray imaging. Journal of Radiological Science and？Technology. 2023;46(3):197-205. DOI: https://doi.org/10.17946/JRST.2023.46.3.197？

원문보기 상세보기

내보내기 구분	파일저장 인쇄 메일전송
구성항목	기본정보 상세정보 관리번호, 논문명, 저널/프로시딩명, 저자 , 발행년, 권, 호, 시작페이지, 끝페이지, 발행기관 관리번호, 논문명, 대등논문명, 저자 , 저널/프로시딩명, 발행기관, 발행년, 발행언어, 권, 호, 시작페이지, 끝페이지, ISBN, ISSN, 주제분야, 키워드, 초록(한글), 초록(영문), 저자(소속기관)
저장형식	Text(ASCII format) Excel format RefWorks Direct Export RIS format (for Reference Manager, ProCite, EndNote), Scholar's Aids, Mendeley
메일정보	받는사람 (필수) @ 보내는사람 (선택) @ 제목 내용 KISTI 검색결과 이메일 서비스
안내	총 건의 자료가 검색되었습니다. 다운받으실 자료의 인덱스를 입력하세요. (1-10,000) 검색결과의 순서대로 최대 10,000건 까지 다운로드가 가능합니다. 데이타가 많을 경우 속도가 느려질 수 있습니다.(최대 2~3분 소요) 다운로드 파일은 UTF-8 형태로 저장됩니다. 파일의 내용이 제대로 보이지 않을실 때는 웹브라우저 상단의 보기 -> 인코딩 -> 자동선택 여부를 확인하십시오. ~ Text(ASCII format) Excel format

연합인증

[국내논문] 3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성
Usefulness of an Auxiliary Tool for Hand Radiography by Using 3D Printing 원문보기

Abstract ▼ AI-Helper

주제어

참고문헌 (18)

이 논문을 인용한 문헌

관련 콘텐츠

원문 보기

원문 URL 링크

오픈액세스(OA) 유형

연관된 기능

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트

연합인증

[국내논문] 3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성 Usefulness of an Auxiliary Tool for Hand Radiography by Using 3D Printing 원문보기

Abstract ▼ AI-Helper

주제어

참고문헌 (18)

이 논문을 인용한 문헌

관련 콘텐츠

원문 보기

원문 URL 링크

오픈액세스(OA) 유형

연관된 기능

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트

[국내논문] 3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성
Usefulness of an Auxiliary Tool for Hand Radiography by Using 3D Printing 원문보기