최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기塑性と加工 = Journal of Japan Society for Technology of Plasticity, v.58 no.680, 2017년, pp.748 - 752
초록이 없습니다.
10.1016/j.jmatprotec.2015.12.019 9) Langner, J. et al.:Investigation of a moveable flash gap in hot forging, J. Mater. Process. Technol., 231 (2016), 199-208.
10.1016/j.jmatprotec.2015.11.019 20) Khan, A. et al.:An alternative explanation of forming force reduction for forming process submitted to vibration:Influence of the waveform in the viscoplastic domain, J. Mater. Process. Technol., 230 (2016), 288-299.
10.1016/j.jmatprotec.2016.03.016 21) Grechnikov, F. et al.:Estimation of hot stamping lubricant efficiency under dynamic loading conditions, ibid., 234 (2016), 300-308.
10.1016/j.cirp.2016.04.013 23) Ahn, D. G. et al.:Improvement of the wear resistance of hot forging dies using a locally selective deposition technology with transition layers, CIRP Annals-Manuf. Technol., 65 (2016), 257-260.
10.1016/j.jmatprotec.2015.09.011 42) Sun, Z. et al.:Tri-modal microstructure evolution of TA15 Ti-alloy under conventional forging combined with given subsequent heart treatment, J. Mater. Process. Technol., 229 (2016), 72-81.
10.1016/j.jmatprotec.2015.12.009 43) Segal, V. et al.:Newhot thermo-mechanical processing of heat treatable aluminum alloys, ibid., 231 (2016), 50-57.
10.1016/j.jmatprotec.2016.05.021 44) Springer, P. et al.:Characterization of mechanical behavior of 18CrNiMo7-6 steel with and without Nb under warm forging conditions through processing maps analysis, ibid., 237 (2016), 216-234.
10.1002/srin.201500234 47) Xu, J. et al.:A comparison of hot deformation behavior of high-Cr white cast iron and high-Cr white cast iron/low carbon steel laminate, steel research int., 87 -6 (2016), 780-788.
10.1002/adem.201500426 48) Rezaee, M. et al.:Flow characterization of a duplex near α Ti6242 alloy through interrelation of micro structural evolution, 3D activation energy map, and processing map, Adv. Eng. Mater., 18 -6 (2016), 1075-1085.
10.1016/j.jmatprotec.2015.09.035 62) Neag, A. et al.:Comparison between numerical simulation of semisolid flow into a die using FORGE and in situ visualization using a transparent sided die, J. Mater. Process. Technol., 229 (2016), 338-348.
10.1002/srin.201400526 71) Zhang, C. et al.:Microstructure evolution of a new Dual-Phase steel via Multi-Pass compression defor mation in the (α+γ) region, steel research int., 87 -2 (2016), 157-164.
10.1016/j.jmatprotec.2015.08.017 75) Wang, C. et al.:Influence of ring growth rate on damage development in hot ring rolling, J. Mater. Process. Technol., 227 (2016), 268-280.
10.1016/j.jmatprotec.2015.07.009 76) Jin, J. et al.:A single-step hot stamping-forging process for aluminum alloy shell parts with nonuniform thickness, ibid., 228 (2016), 170-178.
10.1016/j.cirp.2016.04.125 77) Wolfgarten, M. et al.:New method for the manufacturing of curved workpieces by open-die forging, CIRP Annals-Manuf. Technol., 65 (2016), 285-288.
10.1016/j.cirp.2016.04.134 78) Wang, Z. et al.:Forming of light-weight gear wheel by plate forging, ibid., 65 (2016), 293-296.
10.1016/j.cirp.2016.04.132 79) Utsunomiya, H. et al.:Die motion control for die-quench forging process of AA6061 aluminum alloys, ibid., 65 (2016), 297-300.
10.1115/1.4030855 80) Xinghui, H. et al.:Calculation method for rocking die motion track in cold orbital forging, Trans. ASME, J. Manuf. Sci. Eng., 138 -1 (2016), 014501.1-014501.9.
10.1016/j.jmatprotec.2016.06.013 92) Song, M. et al.:Symmetric bending technology using a floating die to forge crank throws for marine engines, J. Mater. Process. Technol., 237 (2016), 197-207.
10.1016/j.jmatprotec.2016.07.028 93) Lui, E. et al.:Effects of chip conditions on the solid state recycling of Ti-6Al-4V machining chips, ibid., 238 (2016), 297-304.
*원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.