참고문헌 (16)

1. 10.2320/materia.46.99 1) H. Semba, Y. Sawaragi, K. Ogawa, A. Natori and T. Kan, “Development of “SUPER304H” austenitic stainless steel tubes with high temperature strength for USC boilers”, Materia Japan, Vol.46, No.2, pp.99-101 (2007). 

   상세보기

2. 2) NIMS Creep Data Sheet, No.56 A, National Institute for Materials Science, Japan (2018). 

3. 10.1016/j.matchar.2018.04.055 3) K. Sawada, K. Sekido, M. Murata, K. Kamihira and K. Kimura, “Precipitation behavior during aging and creep in 18Cr-9Ni-3Cu-Nb-N steel”, Materials Characterization, Vol.141, pp.279-285 (2018). 

   상세보기

4. 4) N. Shinya, J. Kyono, H. Tanaka, M. Murata and Shin Yokoi, “Creep rupture properties and creep fracture mechanism maps for type 304 stainless steel”, Tetsu-to-Hagane, Vol.69, No.14, pp.1668-1675 (1983). 

5. 5) N. Shinya, H. Tanaka, M. Murata, K. Kaise and Shin Yokoi, “Creep fracture mechanism maps based on creep rupture tests up to about 100 000 h for type 316 stainless steel”, Tetsu-to-Hagane, Vol.71, No.1, pp.114-120 (1985). 

6. 10.2355/tetsutohagane1955.78.6_934 6) H. Tanaka, M. Murata and N. Shinya, “Creep fracture modes at high temperature in SUS321H”, Tetsu-to-Hagane, Vol.78, No.6, pp.934-940 (1992). 

   상세보기

7. 10.2355/tetsutohagane1955.83.1_72 7) H. Tanaka, M. Murata, F. Abe and N. Shinya, “Effects of grain boundary precipitates on long-term creep rupture properties of SUS347H steel”, Tetsu-to-Hagane, Vol.83, No.1, pp.72-77 (1997). 

   상세보기

8. 10.2355/tetsutohagane.94.299 8) M. Mitsuhara, K.Ikeda, H. Nakashima, J. Kusumoto and A. Kanaya, “Effect of microstructural change on creep rupture during creep deformation in 18Cr-9Ni-3Cu-Nb-N Steel”, Tetsu-to-Hagane, Vol.94, No.8, pp.299-304 (2008). 

   상세보기

9. 10.1016/j.matchar.2014.03.012 9) D. B. Parka, S. Hong, K. H. Lee, M. Y. Huh, J. Y. Suh, S. C. Lee and W. S. Jung , “High-temperature creep behavior and microstructural evolution of an 18Cr9Ni3CuNbVN austenitic stainless steel”, Materials Characterization, Vol.93 , pp.52-61 (2014). 

   상세보기

10. 10.2472/jsms.66.179 10) K. Kubushiro, Y. Shioda and K. Nomura, “Creep degradation for austenitic stainless steel in KA-SUS304J1HTB”, Journal of the Society of Materials Science, Japan, Vol.66, No.2, pp.179-184 (2017). 

    

11. 11) R. Koterazawa, “Design rule and results of internal pressure creep deformation / rupture tests”, Kouatsuryoku, Vol.3, No.4, pp.497-544 (1965). 

12. 12) JSMS Committee on High Temperature Strength of Materials, “High temperature strength of materials”, pp.90 (2008). 

13. 10.1080/14786437008238426 13) M. F. Ashby, “The deformation of plastically non-homogeneous materials”, The Philosophical Magazine, Vol.21, pp.399-424 (1970). 

    상세보기

14. 10.1016/S1359-6462(02)00335-4 14) L. P. Kubin and A. Mortensen, “Geometrically necessary dislocations and strain-gradient plastically: a few critical issues”, Scripta Materialia, Vol.48, No.2, pp.119-125 (2003). 

    상세보기

15. 10.1016/S0022-5096(98)00103-3 15) H. Gao, Y. Huang, W. D. nix and J. W. Hutchinson, “Mechanism-based strain gradient plasticity - I. Theory”, Journal of the Mechanics and Physics of Solids, Vol.47, No.6, pp.1239-1263 (1999). 

    상세보기

16. 10.1016/j.msea.2010.01.004 16) M. Calcagnotto, D. Ponge, E. Demir and D. Raabe, “Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD”, Materials Science and Engineering A, Vol.527, No.10-11, pp.2738-2746 (2010). 

    상세보기