본 연구의 목표는 슬래브의 콘크리트 타설시 거푸집 동바리 시스템의 불안전으로 발생할 수 있는 거푸집 붕괴의 예방대책을 제시하는 것이다. 연구는 크게 건설안전과 거푸집공사 관련된 문헌을 분석하고 기본적인 이론을 고찰하는 것과 거푸집 붕괴 사례 및 현장의 동바리 시공 상태를 조사하여 붕괴 예방대책을 제시하는 과정으로 진행 되었다.본 논문의 구성은 다음과 같다. 제1장은 서론과 연구의 배경, 연구목적, 연구목표 및 추진방법에 대하여 논하였으며, 제2장은 거푸집 동바리의 일반사항으로 거푸집 동바리의 정의, 종류, 설계기준, 안전규정, 콘크리트 타설 방법에 대한 일반, 동바리 설계시 주의사항으로 정리하였으며, 제3장은 거푸집 동바리의 현황조사를 통하여 실제 시공되어지는 시공현황을 조사하고, 제4장은 약 10년간의 콘크리트 타설 중 동바리 붕괴 사례를 정밀 분석을 실시하였다.본 논문의 연구결과를 요약하면 다음과 같다.1) 현장관리자나 기능공의 경험에 의존되는 시공형태를 근본적으로 차단하기 위하여, 층고 5m 이상인 구조물의 최초 설계부터 동바리 시스템을 도면화하는 제도적 시스템의 정착이 요구된다. 또한, 층고가 높은 구조물 시공시 주로 사용되어지고 있는 V6 ...
본 연구의 목표는 슬래브의 콘크리트 타설시 거푸집 동바리 시스템의 불안전으로 발생할 수 있는 거푸집 붕괴의 예방대책을 제시하는 것이다. 연구는 크게 건설안전과 거푸집공사 관련된 문헌을 분석하고 기본적인 이론을 고찰하는 것과 거푸집 붕괴 사례 및 현장의 동바리 시공 상태를 조사하여 붕괴 예방대책을 제시하는 과정으로 진행 되었다.본 논문의 구성은 다음과 같다. 제1장은 서론과 연구의 배경, 연구목적, 연구목표 및 추진방법에 대하여 논하였으며, 제2장은 거푸집 동바리의 일반사항으로 거푸집 동바리의 정의, 종류, 설계기준, 안전규정, 콘크리트 타설 방법에 대한 일반, 동바리 설계시 주의사항으로 정리하였으며, 제3장은 거푸집 동바리의 현황조사를 통하여 실제 시공되어지는 시공현황을 조사하고, 제4장은 약 10년간의 콘크리트 타설 중 동바리 붕괴 사례를 정밀 분석을 실시하였다.본 논문의 연구결과를 요약하면 다음과 같다.1) 현장관리자나 기능공의 경험에 의존되는 시공형태를 근본적으로 차단하기 위하여, 층고 5m 이상인 구조물의 최초 설계부터 동바리 시스템을 도면화하는 제도적 시스템의 정착이 요구된다. 또한, 층고가 높은 구조물 시공시 주로 사용되어지고 있는 V6 Support 사용에 대한 안전성 평가 및 품질인증이 요구된다.2) 콘크리트 타설중 발생되는 작업하중 즉 생콘크리트의 유동적인 움직임을 보다 안전하게 하기 위하여 동바리의 수평내력을 확보해야 한다. 이를 위하여 동바리의 간격과 배치가 검토되어야하고, 2단이상 수평연결시 전용 클래프를 사용하여야 한다.3) 거푸집 붕괴사고의 대부분은 콘크리트를 타설하는 과정에서 발생한다. 즉 콘크리트 타설 순서에 따라서 발생하는 부분재하 및 편심재하 효과를 고려한 동바리의 축력 및 수평력 산정이 요구된다.4) 동바리 붕괴사례 49건 가운데 30건의 붕괴사례가 Pipe Support를 2단으로 설치한 동바리 시스템에서 일어난 것에서 알 수 있듯이 Pipe Support의 2단 시공방식의 전반적인 점검이 요구된다.
본 연구의 목표는 슬래브의 콘크리트 타설시 거푸집 동바리 시스템의 불안전으로 발생할 수 있는 거푸집 붕괴의 예방대책을 제시하는 것이다. 연구는 크게 건설안전과 거푸집공사 관련된 문헌을 분석하고 기본적인 이론을 고찰하는 것과 거푸집 붕괴 사례 및 현장의 동바리 시공 상태를 조사하여 붕괴 예방대책을 제시하는 과정으로 진행 되었다.본 논문의 구성은 다음과 같다. 제1장은 서론과 연구의 배경, 연구목적, 연구목표 및 추진방법에 대하여 논하였으며, 제2장은 거푸집 동바리의 일반사항으로 거푸집 동바리의 정의, 종류, 설계기준, 안전규정, 콘크리트 타설 방법에 대한 일반, 동바리 설계시 주의사항으로 정리하였으며, 제3장은 거푸집 동바리의 현황조사를 통하여 실제 시공되어지는 시공현황을 조사하고, 제4장은 약 10년간의 콘크리트 타설 중 동바리 붕괴 사례를 정밀 분석을 실시하였다.본 논문의 연구결과를 요약하면 다음과 같다.1) 현장관리자나 기능공의 경험에 의존되는 시공형태를 근본적으로 차단하기 위하여, 층고 5m 이상인 구조물의 최초 설계부터 동바리 시스템을 도면화하는 제도적 시스템의 정착이 요구된다. 또한, 층고가 높은 구조물 시공시 주로 사용되어지고 있는 V6 Support 사용에 대한 안전성 평가 및 품질인증이 요구된다.2) 콘크리트 타설중 발생되는 작업하중 즉 생콘크리트의 유동적인 움직임을 보다 안전하게 하기 위하여 동바리의 수평내력을 확보해야 한다. 이를 위하여 동바리의 간격과 배치가 검토되어야하고, 2단이상 수평연결시 전용 클래프를 사용하여야 한다.3) 거푸집 붕괴사고의 대부분은 콘크리트를 타설하는 과정에서 발생한다. 즉 콘크리트 타설 순서에 따라서 발생하는 부분재하 및 편심재하 효과를 고려한 동바리의 축력 및 수평력 산정이 요구된다.4) 동바리 붕괴사례 49건 가운데 30건의 붕괴사례가 Pipe Support를 2단으로 설치한 동바리 시스템에서 일어난 것에서 알 수 있듯이 Pipe Support의 2단 시공방식의 전반적인 점검이 요구된다.
Forms are frequently collapsed during slab concrete works due to unstable strut system. The purpose of this study is to suggest the ways to prevent the form struts from being collapsed. To this end, relevant literature, dissertations and reports about construction safety and form construction were r...
Forms are frequently collapsed during slab concrete works due to unstable strut system. The purpose of this study is to suggest the ways to prevent the form struts from being collapsed. To this end, relevant literature, dissertations and reports about construction safety and form construction were reviewed theoretically, and thereupon, construction spots were surveyed to examine constructions of struts.This study consists of the following chapters. The first chapter introduces background, purpose, objectives and methods of study. The second chapter describes the form struts in general: definition, types, design guidelines, concrete works, cautions for strut design, etc. The third chapter sums up the result of a survey about form struts being constructed. The fourth chapter analyzes the cases for the last decade where struts were collapsed during concrete works.The methods to prevent the forms from being collapsed can be summarized as follows;1) When the structures 5m or higher are designed initially, it is necessary to document them specifically and thereby, establish a system for construction of struts, discouraging spot managers or workers from relying on their experiences. Furthermore, it is also necessary to review the safety of V6 supports popular on the spots for high-rise buildings but not certified for their safety and thereby, authorize their uses to remove the room for any controversy between supervisor and workers.2) In order to stabilize the workload or the mobility of raw concrete during concrete work and thereby, secure the horizontal strength of struts, it is required to maintain proper intervals of struts, their rows and columns, while using a horizontal linkage of 2 stage or more as a dedicated clamp for struts, and therewith, install a structure resisting the mobile load of raw concrete.3) The forms collapses mostly during concrete work because of improper sequence of concrete work. Accordingly, it is necessary to estimate the axial and horizontal strength of strut in consideration of partial and eccentric loads during concrete work.4) It was found through this study that 30 cases out of 49 strut collapses had been caused by the strut system with 2-stage pipe supports installed, and therefore, it is deemed required to reconsider this construction method.
Forms are frequently collapsed during slab concrete works due to unstable strut system. The purpose of this study is to suggest the ways to prevent the form struts from being collapsed. To this end, relevant literature, dissertations and reports about construction safety and form construction were reviewed theoretically, and thereupon, construction spots were surveyed to examine constructions of struts.This study consists of the following chapters. The first chapter introduces background, purpose, objectives and methods of study. The second chapter describes the form struts in general: definition, types, design guidelines, concrete works, cautions for strut design, etc. The third chapter sums up the result of a survey about form struts being constructed. The fourth chapter analyzes the cases for the last decade where struts were collapsed during concrete works.The methods to prevent the forms from being collapsed can be summarized as follows;1) When the structures 5m or higher are designed initially, it is necessary to document them specifically and thereby, establish a system for construction of struts, discouraging spot managers or workers from relying on their experiences. Furthermore, it is also necessary to review the safety of V6 supports popular on the spots for high-rise buildings but not certified for their safety and thereby, authorize their uses to remove the room for any controversy between supervisor and workers.2) In order to stabilize the workload or the mobility of raw concrete during concrete work and thereby, secure the horizontal strength of struts, it is required to maintain proper intervals of struts, their rows and columns, while using a horizontal linkage of 2 stage or more as a dedicated clamp for struts, and therewith, install a structure resisting the mobile load of raw concrete.3) The forms collapses mostly during concrete work because of improper sequence of concrete work. Accordingly, it is necessary to estimate the axial and horizontal strength of strut in consideration of partial and eccentric loads during concrete work.4) It was found through this study that 30 cases out of 49 strut collapses had been caused by the strut system with 2-stage pipe supports installed, and therefore, it is deemed required to reconsider this construction method.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.