전류-제어 슈미트 트리거를 이용한 인체 신호 감지용 센서 인터페이스 회로를 제안하였다. 설계한 회로는 RFID와 연동되어 동작하며 인체에 내장될 수 있도록 작은 면적을 가진다. 또한 기존 방식과 비교하였을 때, 간단한 회로구성과, 높은 분해능, 그리고 저전력의 특징을 보인다. 제안한 회로는 하나의 전류-제어 슈미트 트리거, 램프 발생기, 8-비트 카운터, 8-비트 래치, 4개의 게이트로 구성된다. RFID에서 수신신호가 들어오면 센서 아날로그 출력 신호를 ...
전류-제어 슈미트 트리거를 이용한 인체 신호 감지용 센서 인터페이스 회로를 제안하였다. 설계한 회로는 RFID와 연동되어 동작하며 인체에 내장될 수 있도록 작은 면적을 가진다. 또한 기존 방식과 비교하였을 때, 간단한 회로구성과, 높은 분해능, 그리고 저전력의 특징을 보인다. 제안한 회로는 하나의 전류-제어 슈미트 트리거, 램프 발생기, 8-비트 카운터, 8-비트 래치, 4개의 게이트로 구성된다. RFID에서 수신신호가 들어오면 센서 아날로그 출력 신호를 디지털 신호로 변환시킨 후, RFID를 통해서 마이컴으로 송신한다. 설계한 회로는 0.35 ㎛ CMOS파라미터를 사용하여 시뮬레이션 되었다. 시뮬레이션 결과는 회로의 감지 가능한 최소 전류변화는 0.25 ㎂이고, 변환 선형오차는 ±0.02% 미만이라는 것을 보인다.
전류-제어 슈미트 트리거를 이용한 인체 신호 감지용 센서 인터페이스 회로를 제안하였다. 설계한 회로는 RFID와 연동되어 동작하며 인체에 내장될 수 있도록 작은 면적을 가진다. 또한 기존 방식과 비교하였을 때, 간단한 회로구성과, 높은 분해능, 그리고 저전력의 특징을 보인다. 제안한 회로는 하나의 전류-제어 슈미트 트리거, 램프 발생기, 8-비트 카운터, 8-비트 래치, 4개의 게이트로 구성된다. RFID에서 수신신호가 들어오면 센서 아날로그 출력 신호를 디지털 신호로 변환시킨 후, RFID를 통해서 마이컴으로 송신한다. 설계한 회로는 0.35 ㎛ CMOS 파라미터를 사용하여 시뮬레이션 되었다. 시뮬레이션 결과는 회로의 감지 가능한 최소 전류변화는 0.25 ㎂이고, 변환 선형오차는 ±0.02% 미만이라는 것을 보인다.
A bio-sensor interface circuit using a current-tunable Schmitt trigger is presented. It consists of a current-tunable Schmitt trigger, a ramp generator, an 8-bit counter, an 8-bit latch, and four logic gates. It features simple configuration, high resolution, and low power. If the circuit detects th...
A bio-sensor interface circuit using a current-tunable Schmitt trigger is presented. It consists of a current-tunable Schmitt trigger, a ramp generator, an 8-bit counter, an 8-bit latch, and four logic gates. It features simple configuration, high resolution, and low power. If the circuit detects the analog signal from the RFID, it converts the analog signal to the digital signal and the digital signal is transmitted to the micom through the RFID. The prototype circuit has been simulated using 0.35-㎛ CMOS parameters. Simulation results show that the minimum detectable current variation of the circuit is 0.25 and the conversion linearity error is less than ±0.02%.
A bio-sensor interface circuit using a current-tunable Schmitt trigger is presented. It consists of a current-tunable Schmitt trigger, a ramp generator, an 8-bit counter, an 8-bit latch, and four logic gates. It features simple configuration, high resolution, and low power. If the circuit detects the analog signal from the RFID, it converts the analog signal to the digital signal and the digital signal is transmitted to the micom through the RFID. The prototype circuit has been simulated using 0.35-㎛ CMOS parameters. Simulation results show that the minimum detectable current variation of the circuit is 0.25 and the conversion linearity error is less than ±0.02%.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.