군은 현재 약 10만여 동, 2,520만㎡의 방대한 시설을 보유하고 있으나 20년 이상 경과된 노후시설이 전체의 약 30%를 차지하고 있으므로 군에서는 이러한 노후시설들의 안전과 성능저하 문제를 해결하며 또한 국가 경제수준에 부합되는 장병들의 삶의 질 향상을 위하여 새로운 공법과 사업방식으로 병영시설 개선사업을 추진하고 있다. 향후 국방개혁 2020에 의한 부대이전·해체, 증·창설 등과 같은 구조 개편 시 안보환경 변화에 대응할 수 있도록 모듈러 건축시스템을 채택하여 2005년부터 내무생활관, 소초시설 등 일부 시설에 대해 시험시공을 실시하였고 현재에도 부분적으로 본 공법을 적용하여 시공 중에 있다. 이동성능이 우수한 ...
군은 현재 약 10만여 동, 2,520만㎡의 방대한 시설을 보유하고 있으나 20년 이상 경과된 노후시설이 전체의 약 30%를 차지하고 있으므로 군에서는 이러한 노후시설들의 안전과 성능저하 문제를 해결하며 또한 국가 경제수준에 부합되는 장병들의 삶의 질 향상을 위하여 새로운 공법과 사업방식으로 병영시설 개선사업을 추진하고 있다. 향후 국방개혁 2020에 의한 부대이전·해체, 증·창설 등과 같은 구조 개편 시 안보환경 변화에 대응할 수 있도록 모듈러 건축시스템을 채택하여 2005년부터 내무생활관, 소초시설 등 일부 시설에 대해 시험시공을 실시하였고 현재에도 부분적으로 본 공법을 적용하여 시공 중에 있다. 이동성능이 우수한 모듈러 공법은 단위모듈을 공장에서 완성하고 현장으로 운송한 후 조립하여 건축물을 완성하는 가장 발전된 공업화 건축공법으로 군에서는 숙영, 행정, 복지 및 저장시설 등에 제한적으로 적용하였으나 장차 군 구조 개편에 따른 이동·재사용과 긴급소요시설에 대한 공기단축을 위해 모듈러 건축시스템의 수요는 점차 증가할 것으로 예상된다. 따라서 본 연구에서는 군에 모듈러 공법을 확대적용하기 전에 국내ㆍ외의 개발 및 적용 실태를 파악하며 여러 가지 군 시설 중 적용가능 시설을 확정하고 그동안 군 시설공사 집행 시 나타난 문제점을 분석하여 공법 적용이 가장 유리한 독신자 숙소에 대한 모듈러 시스템을 개발하여 제시하며 주요 연구결과는 다음과 같다. (1) 모듈러 공법은 내무생활관, 독신자숙소, 행정시설, 위병소, 면회실과 같은 중소규모 시설건립에 적합하지만 1모듈로 1실을 구성할 수 있는 독신자숙소가 가장 유리하며 단위모듈은 높이 3.3m, 폭 3.3m, 길이 12m 이하로 하고 중량은 5톤 이하로 제한하는 것이 적당하다. (2) 초기투자비 분석결과, 모듈러 공법은 초기단계에서는 시설투자비가 상대적으로 저렴한 소규모시설 위주로 적용하여야 하며 초기투자비 절감을 위해 저렴한 내화구조를 개발하고 지붕은 모듈제작 시 최상층 모듈에 부착·제작하여야 한다. (3) 입주자의 편의성, 우리나라 도로조건과 모듈제작을 위한 철골 골조량의 최소화 등을 고려하여 단위 실은 폭 3.3m, 길이 4.4m로 하고 현장 공기단축, 모듈의 용이한 해체와 호환, 공장 제작비율 향상을 위해 1실당 1모듈로 제작·조립한다. (4) 단면은 충분한 실내 천정고(2.4m)를 확보할 수 있고 방수관련 하자가 적으며, 기존 시설과 유사한 경사지붕형태를 적용하고 차음성능 향상을 위해 바닥의 스판크리트 하부를 합판과 단열재로 보강하며 벽체에는 석고보드, 발포 저밀도 폴리에틸렌, 단열재를 설치한다. (5) 외장은 공장 제작이 편리하고 재사용율이 높으며 초기 투자비 및 유지비가 적게 소요되는 알루미늄 복합 패널을 적용하고 기계설비는 쾌적한 실내환경, 유지관리와 재사용성을 고려하여 전기 방열기를 이용한 난방과 순간 전기 온수기를 이용한 급탕방식을 적용한다. (6) 모듈러 공법의 순공사기간은 철근콘크리트조 대비 50%미만이며 1개 단위 모듈당 공장제작에 7.9시간, 기초 등 현장공사에 1.4시간, 현장조립에 4.8시간으로 총 14.1시간이 소요되지만, 각각의 공정을 중첩하여 공기를 단축함으로써 총 11.8시간을 단위 모듈의 표준공기로 설정한다. (7) 군에서 적용하였던 사업에 대해 설계, 공장제작, 이송, 현장조립 단계 등으로 구분하여 문제점을 도출하고, 각 단계에서 시공자 또는 공사관리자가 쉽게 점검할 수 있도록 시공방법과 중점관리항목을 포함한 현장관리 시스템을 제시한다. 본 연구는 최근 국내에서 개발된 모듈러 시스템을 군에 확대적용하기 위해 본 공법의 활용이 가장 유리한 모듈러 독신자 숙소의 기본계획과 시공단계에서의 현장관리 시스템을 제시함으로써 향후 유사시설의 계획 및 집행 시 비용절감, 공기단축과 품질향상에 기여할 수 있을 것으로 기대한다.
군은 현재 약 10만여 동, 2,520만㎡의 방대한 시설을 보유하고 있으나 20년 이상 경과된 노후시설이 전체의 약 30%를 차지하고 있으므로 군에서는 이러한 노후시설들의 안전과 성능저하 문제를 해결하며 또한 국가 경제수준에 부합되는 장병들의 삶의 질 향상을 위하여 새로운 공법과 사업방식으로 병영시설 개선사업을 추진하고 있다. 향후 국방개혁 2020에 의한 부대이전·해체, 증·창설 등과 같은 구조 개편 시 안보환경 변화에 대응할 수 있도록 모듈러 건축시스템을 채택하여 2005년부터 내무생활관, 소초시설 등 일부 시설에 대해 시험시공을 실시하였고 현재에도 부분적으로 본 공법을 적용하여 시공 중에 있다. 이동성능이 우수한 모듈러 공법은 단위모듈을 공장에서 완성하고 현장으로 운송한 후 조립하여 건축물을 완성하는 가장 발전된 공업화 건축공법으로 군에서는 숙영, 행정, 복지 및 저장시설 등에 제한적으로 적용하였으나 장차 군 구조 개편에 따른 이동·재사용과 긴급소요시설에 대한 공기단축을 위해 모듈러 건축시스템의 수요는 점차 증가할 것으로 예상된다. 따라서 본 연구에서는 군에 모듈러 공법을 확대적용하기 전에 국내ㆍ외의 개발 및 적용 실태를 파악하며 여러 가지 군 시설 중 적용가능 시설을 확정하고 그동안 군 시설공사 집행 시 나타난 문제점을 분석하여 공법 적용이 가장 유리한 독신자 숙소에 대한 모듈러 시스템을 개발하여 제시하며 주요 연구결과는 다음과 같다. (1) 모듈러 공법은 내무생활관, 독신자숙소, 행정시설, 위병소, 면회실과 같은 중소규모 시설건립에 적합하지만 1모듈로 1실을 구성할 수 있는 독신자숙소가 가장 유리하며 단위모듈은 높이 3.3m, 폭 3.3m, 길이 12m 이하로 하고 중량은 5톤 이하로 제한하는 것이 적당하다. (2) 초기투자비 분석결과, 모듈러 공법은 초기단계에서는 시설투자비가 상대적으로 저렴한 소규모시설 위주로 적용하여야 하며 초기투자비 절감을 위해 저렴한 내화구조를 개발하고 지붕은 모듈제작 시 최상층 모듈에 부착·제작하여야 한다. (3) 입주자의 편의성, 우리나라 도로조건과 모듈제작을 위한 철골 골조량의 최소화 등을 고려하여 단위 실은 폭 3.3m, 길이 4.4m로 하고 현장 공기단축, 모듈의 용이한 해체와 호환, 공장 제작비율 향상을 위해 1실당 1모듈로 제작·조립한다. (4) 단면은 충분한 실내 천정고(2.4m)를 확보할 수 있고 방수관련 하자가 적으며, 기존 시설과 유사한 경사지붕형태를 적용하고 차음성능 향상을 위해 바닥의 스판크리트 하부를 합판과 단열재로 보강하며 벽체에는 석고보드, 발포 저밀도 폴리에틸렌, 단열재를 설치한다. (5) 외장은 공장 제작이 편리하고 재사용율이 높으며 초기 투자비 및 유지비가 적게 소요되는 알루미늄 복합 패널을 적용하고 기계설비는 쾌적한 실내환경, 유지관리와 재사용성을 고려하여 전기 방열기를 이용한 난방과 순간 전기 온수기를 이용한 급탕방식을 적용한다. (6) 모듈러 공법의 순공사기간은 철근콘크리트조 대비 50%미만이며 1개 단위 모듈당 공장제작에 7.9시간, 기초 등 현장공사에 1.4시간, 현장조립에 4.8시간으로 총 14.1시간이 소요되지만, 각각의 공정을 중첩하여 공기를 단축함으로써 총 11.8시간을 단위 모듈의 표준공기로 설정한다. (7) 군에서 적용하였던 사업에 대해 설계, 공장제작, 이송, 현장조립 단계 등으로 구분하여 문제점을 도출하고, 각 단계에서 시공자 또는 공사관리자가 쉽게 점검할 수 있도록 시공방법과 중점관리항목을 포함한 현장관리 시스템을 제시한다. 본 연구는 최근 국내에서 개발된 모듈러 시스템을 군에 확대적용하기 위해 본 공법의 활용이 가장 유리한 모듈러 독신자 숙소의 기본계획과 시공단계에서의 현장관리 시스템을 제시함으로써 향후 유사시설의 계획 및 집행 시 비용절감, 공기단축과 품질향상에 기여할 수 있을 것으로 기대한다.
The ROK military currently possesses extensive accommodation facilities of about 100 thousand buildings, measuring 25 million ㎡. Yet, about thirty percent of the total facilities are old which were built over twenty years ago. The military anticipates problems of old facilities such as safety and fu...
The ROK military currently possesses extensive accommodation facilities of about 100 thousand buildings, measuring 25 million ㎡. Yet, about thirty percent of the total facilities are old which were built over twenty years ago. The military anticipates problems of old facilities such as safety and functional aspects while at the same time, striving to improve the military personnels' quality of life that matches the country's economic standing by attempting renovation of the facilities using an advanced technology through public-private partnership. Also, in an attempt to prepare for unforeseen changes in security environment such as unit movement, dismantling, extension of facilities the military has adopted the modular system of construction since 2005. It constructed some barracks as a pilot project and is currently using this method at several sites. The modular construction, which has a good mobility capability, is the most developed construction method in building a structure by prefabricating the unit modules in a factory and then transferring them to a construction site for assembly. In the military, the application of modular construction method has been limited to structures such as barracks, administration blocks, welfare and storage spaces. It is anticipated that the demand for modular construction system is likely to increase because of high mobility, reusability and the advantage of shortening the construction period for urgent requirements. Thus, the aim of the thesis is to study the aspects of both production and application of modular construction in Korea as well as abroad. The paper lists the various military facilities that are suitable for modular construction method and analyzes problems that occurred during construction of these facilities. It develops and suggests a modular system for defense bachelor officers' quarters(BOQ) which has the highest potential for application of this construction method. The main theoretical contributions of the thesis are as the follows: (1) The modular construction is suitable for constructing small to midium size facilities such as barrack, BOQ, administration building, guard post. But it is best suited for constructing BOQ which only takes 1 module to construct a single room. It proposes to set up a unit module with height 3.3m, width 3.3m, length 12m, and weight 5tons or less. (2) According to the result of the initial cost analysis, the modular construction method is cost-minimizing for small size facilities. Thus, it should be applied to small size facilities in the initial stage. Also, in order to reduce initial construction cost, it is necessary to develop low-cost fire proof structure. When fabricating the module, the roof should be attached to the top surface of the module. (3) Taking such factors as resident's convenience, road conditions in Korea and minimization of steel frame for module construction into account, the most suitable unit room size is 3.3m wide and 4.4m long. In order to shorten construction duration, facilitate dismantling of modules and enhance manufacturing ratio in a factory, 1 module should be produced and assembled for a single room. (4) Sloping roof with ceiling height 2.4m which is similar to existing buildings is used in this paper. This type of roof is enough for plumbing and a defection of water seepage and leakage. For sound proof, plywood and expanded polystyrene are used under floor and gypsum board, low density polyethylene, and expanded polystyrene are used in wall. (5) Aluminium composite pannels are applied for cladding as they are easy to manufacture in a factory, while their reuse ratio is high and initial cost is low. Electric radiator and instant water heater are used for room heating and making hot water since they are easy to operate, maintain and reuse. (6) Net construction period of modular construction method is 50% less than reinforced concrete structures. One unit of module takes 7.9 hours to produce in the factory, 1.4 hours for on-site construction and 4.8 hours for on-site assembly. In the paper, total time of 11.8 hours has been computed as the standard construction time, taking into consideration the overlapping period in each phase. On the basis of the construction used in the military, problems of each process including design, manufacturing in a factory, transportation, and on site assembly have been identified and listed separately. At each stage, on-site inspection including detailed specification and important management check off list is proposed to facilitate the constructors and manager's inspection process. In order to expand the application of the modular system that has been recently developed in Korea, this thesis suggests on-site system for primary plan and construction process for BOQ which is most suitable for this construction method. Futhermore it expects to minimize cost and construction duration and enhance quality in planning and constructing similar facilities in the future.
The ROK military currently possesses extensive accommodation facilities of about 100 thousand buildings, measuring 25 million ㎡. Yet, about thirty percent of the total facilities are old which were built over twenty years ago. The military anticipates problems of old facilities such as safety and functional aspects while at the same time, striving to improve the military personnels' quality of life that matches the country's economic standing by attempting renovation of the facilities using an advanced technology through public-private partnership. Also, in an attempt to prepare for unforeseen changes in security environment such as unit movement, dismantling, extension of facilities the military has adopted the modular system of construction since 2005. It constructed some barracks as a pilot project and is currently using this method at several sites. The modular construction, which has a good mobility capability, is the most developed construction method in building a structure by prefabricating the unit modules in a factory and then transferring them to a construction site for assembly. In the military, the application of modular construction method has been limited to structures such as barracks, administration blocks, welfare and storage spaces. It is anticipated that the demand for modular construction system is likely to increase because of high mobility, reusability and the advantage of shortening the construction period for urgent requirements. Thus, the aim of the thesis is to study the aspects of both production and application of modular construction in Korea as well as abroad. The paper lists the various military facilities that are suitable for modular construction method and analyzes problems that occurred during construction of these facilities. It develops and suggests a modular system for defense bachelor officers' quarters(BOQ) which has the highest potential for application of this construction method. The main theoretical contributions of the thesis are as the follows: (1) The modular construction is suitable for constructing small to midium size facilities such as barrack, BOQ, administration building, guard post. But it is best suited for constructing BOQ which only takes 1 module to construct a single room. It proposes to set up a unit module with height 3.3m, width 3.3m, length 12m, and weight 5tons or less. (2) According to the result of the initial cost analysis, the modular construction method is cost-minimizing for small size facilities. Thus, it should be applied to small size facilities in the initial stage. Also, in order to reduce initial construction cost, it is necessary to develop low-cost fire proof structure. When fabricating the module, the roof should be attached to the top surface of the module. (3) Taking such factors as resident's convenience, road conditions in Korea and minimization of steel frame for module construction into account, the most suitable unit room size is 3.3m wide and 4.4m long. In order to shorten construction duration, facilitate dismantling of modules and enhance manufacturing ratio in a factory, 1 module should be produced and assembled for a single room. (4) Sloping roof with ceiling height 2.4m which is similar to existing buildings is used in this paper. This type of roof is enough for plumbing and a defection of water seepage and leakage. For sound proof, plywood and expanded polystyrene are used under floor and gypsum board, low density polyethylene, and expanded polystyrene are used in wall. (5) Aluminium composite pannels are applied for cladding as they are easy to manufacture in a factory, while their reuse ratio is high and initial cost is low. Electric radiator and instant water heater are used for room heating and making hot water since they are easy to operate, maintain and reuse. (6) Net construction period of modular construction method is 50% less than reinforced concrete structures. One unit of module takes 7.9 hours to produce in the factory, 1.4 hours for on-site construction and 4.8 hours for on-site assembly. In the paper, total time of 11.8 hours has been computed as the standard construction time, taking into consideration the overlapping period in each phase. On the basis of the construction used in the military, problems of each process including design, manufacturing in a factory, transportation, and on site assembly have been identified and listed separately. At each stage, on-site inspection including detailed specification and important management check off list is proposed to facilitate the constructors and manager's inspection process. In order to expand the application of the modular system that has been recently developed in Korea, this thesis suggests on-site system for primary plan and construction process for BOQ which is most suitable for this construction method. Futhermore it expects to minimize cost and construction duration and enhance quality in planning and constructing similar facilities in the future.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.