여러 가지 전단가공은 기계, 자동차 전기전자산업 및 최근 컴퓨터, 우주 항공 산업을 비롯한 기타 부품 산업의 기반기술로서 대량생산을 할 수 있는 매우 중요한 방법이다. 갈수록 공업제품들은 다품종 소량생산과 신소재에 대한 대응 및 기계적 특성과 고 정밀도화, 고품질화가 크게 요구되며, 특히 형상의 복잡화 등 엄격해진 요구 조건 등으로 인한 파인 블랭킹 가공기술의 부족과 고가의 생산 장비 비용을 부담해야 되기 때문에 자체의 기술개발이 어렵고 수입에 의존하고 있는 실정이다. 본 연구에서는 범용 프레스 (160t)를 이용하여, 파인블랭킹 ...
여러 가지 전단가공은 기계, 자동차 전기전자산업 및 최근 컴퓨터, 우주 항공 산업을 비롯한 기타 부품 산업의 기반기술로서 대량생산을 할 수 있는 매우 중요한 방법이다. 갈수록 공업제품들은 다품종 소량생산과 신소재에 대한 대응 및 기계적 특성과 고 정밀도화, 고품질화가 크게 요구되며, 특히 형상의 복잡화 등 엄격해진 요구 조건 등으로 인한 파인 블랭킹 가공기술의 부족과 고가의 생산 장비 비용을 부담해야 되기 때문에 자체의 기술개발이 어렵고 수입에 의존하고 있는 실정이다. 본 연구에서는 범용 프레스 (160t)를 이용하여, 파인블랭킹 금형을 설치하고, 실험 조건으로 전단면의 형성에 중요한 영향을 미치는 V형 압입링의 각도와 전단선에서 부터의 거리, V형 압입링이 피 가공판재에 파고 들어가는 압입하는 힘 및 제품의 생산에 큰 영향을 미치는 생산 속도를 변화 시키면서 전단면과 파단면의 분포를 분석하였다. 실험에 사용된 피 가공판재는 냉간 압연강판(SPCC 1종 드로잉용) 3.0t를 사용하였으며, 최대하중 21.68, Stress 이며, Strain 이고, 조직검사 결과 Ferrite를 다량 함유한 연질의 조직으로 조사되었다. V형 압입링의 힘은 전단가공을 할 때에 재료의 유동을 억제하고, 확실한 클램핑 할 때에 유효 전단면이 넓게 되었다. 본 실험에서는 이 압력을 범용 프레스의 다이 쿠션을 이용하여 139.74 ()으로 하고, 이때의 전단 속도를 6.4m/min으로 할 때에 압입율 97.67%가 되며, 가장 넓은 유효 전단면을 얻게 되었다. V형 압입링의 거리를 전단면으로부터 1.5mm, 2.0mm, 2.5mm의 3가지 조건으로 실험한 결과 1.5mm에서는 전단면의 크기가 피 가공 판재 두께의 87.22%, 2.0mm에서는 89.53%이며, 2.5mm에서는 86.08%로 전단되었다. V형 압입링의 각도를 외측30°/내측45°, 외측45°/내측45° 및 외측45°/내측30°로 변화시키면서 실험한 결과 외측30°/내측45°에서는 유효전단면이 85.65%로 고찰되었으며, 외측45°/내측45°에서는 87.38%이며, 45°/내측30°에서는 89.81%로 고찰되었다. 그리고 생산성에 영향을 미치는 전단속도에 있어서는 6.4m/min과 10m/min 및 16m/min의 3가지 조건으로 하고, 각도를 위 실험에서 부여한 조건 3가지를 함께 적용시켜 전단면의 분포를 연구 고찰하였다. 그 결과로는6.4m/min의 외측30°/내측45°에서 유효 전단면은 85.66%이며, 10m/min의 외측30°/내측45°에서 유효 전단면은 85.40%이며, 16m/min의 외측30°/내측45°에서 유효 전단면은 87.11%로 고찰되었다. 6.4m/min의 외측45°/내측45°에서 유효 전단면은 87.38%이며, 10m/min의 외측45°/내측45°에서 유효 전단면은 85.76%이며, 16m/min의 외측45°/내측45°에서 유효 전단면은 85.04%로 고찰되었다. 6.4m/min의 외측45°/내측30°에서 유효 전단면은 89.81%이며, 10m/min의 외측45°/내측30°에서 유효 전단면은 87.12%이며, 16m/min의 외측45°/내측30°에서 유효 전단면은 86.61%로 고찰되었다. 전단속도를 변화시키면서 실험한 결과 전단속도 6.4m/min에 V형 압입링의 거리 2.0mm, 각도 외측45°/내측30°의 경우에서 91.77%의 유효 전단면을 얻을 수 있었다. 전단 속도가 빠르게 되면 유효 전단면의 면적이 작게 됨을 알 수 있다.
여러 가지 전단가공은 기계, 자동차 전기전자산업 및 최근 컴퓨터, 우주 항공 산업을 비롯한 기타 부품 산업의 기반기술로서 대량생산을 할 수 있는 매우 중요한 방법이다. 갈수록 공업제품들은 다품종 소량생산과 신소재에 대한 대응 및 기계적 특성과 고 정밀도화, 고품질화가 크게 요구되며, 특히 형상의 복잡화 등 엄격해진 요구 조건 등으로 인한 파인 블랭킹 가공기술의 부족과 고가의 생산 장비 비용을 부담해야 되기 때문에 자체의 기술개발이 어렵고 수입에 의존하고 있는 실정이다. 본 연구에서는 범용 프레스 (160t)를 이용하여, 파인블랭킹 금형을 설치하고, 실험 조건으로 전단면의 형성에 중요한 영향을 미치는 V형 압입링의 각도와 전단선에서 부터의 거리, V형 압입링이 피 가공판재에 파고 들어가는 압입하는 힘 및 제품의 생산에 큰 영향을 미치는 생산 속도를 변화 시키면서 전단면과 파단면의 분포를 분석하였다. 실험에 사용된 피 가공판재는 냉간 압연강판(SPCC 1종 드로잉용) 3.0t를 사용하였으며, 최대하중 21.68, Stress 이며, Strain 이고, 조직검사 결과 Ferrite를 다량 함유한 연질의 조직으로 조사되었다. V형 압입링의 힘은 전단가공을 할 때에 재료의 유동을 억제하고, 확실한 클램핑 할 때에 유효 전단면이 넓게 되었다. 본 실험에서는 이 압력을 범용 프레스의 다이 쿠션을 이용하여 139.74 ()으로 하고, 이때의 전단 속도를 6.4m/min으로 할 때에 압입율 97.67%가 되며, 가장 넓은 유효 전단면을 얻게 되었다. V형 압입링의 거리를 전단면으로부터 1.5mm, 2.0mm, 2.5mm의 3가지 조건으로 실험한 결과 1.5mm에서는 전단면의 크기가 피 가공 판재 두께의 87.22%, 2.0mm에서는 89.53%이며, 2.5mm에서는 86.08%로 전단되었다. V형 압입링의 각도를 외측30°/내측45°, 외측45°/내측45° 및 외측45°/내측30°로 변화시키면서 실험한 결과 외측30°/내측45°에서는 유효전단면이 85.65%로 고찰되었으며, 외측45°/내측45°에서는 87.38%이며, 45°/내측30°에서는 89.81%로 고찰되었다. 그리고 생산성에 영향을 미치는 전단속도에 있어서는 6.4m/min과 10m/min 및 16m/min의 3가지 조건으로 하고, 각도를 위 실험에서 부여한 조건 3가지를 함께 적용시켜 전단면의 분포를 연구 고찰하였다. 그 결과로는6.4m/min의 외측30°/내측45°에서 유효 전단면은 85.66%이며, 10m/min의 외측30°/내측45°에서 유효 전단면은 85.40%이며, 16m/min의 외측30°/내측45°에서 유효 전단면은 87.11%로 고찰되었다. 6.4m/min의 외측45°/내측45°에서 유효 전단면은 87.38%이며, 10m/min의 외측45°/내측45°에서 유효 전단면은 85.76%이며, 16m/min의 외측45°/내측45°에서 유효 전단면은 85.04%로 고찰되었다. 6.4m/min의 외측45°/내측30°에서 유효 전단면은 89.81%이며, 10m/min의 외측45°/내측30°에서 유효 전단면은 87.12%이며, 16m/min의 외측45°/내측30°에서 유효 전단면은 86.61%로 고찰되었다. 전단속도를 변화시키면서 실험한 결과 전단속도 6.4m/min에 V형 압입링의 거리 2.0mm, 각도 외측45°/내측30°의 경우에서 91.77%의 유효 전단면을 얻을 수 있었다. 전단 속도가 빠르게 되면 유효 전단면의 면적이 작게 됨을 알 수 있다.
A various shearing operation including a machine, a automotive, electricity, electronics industry,a space and aviation industry are a very importance method which can be produce a great much of quantity as on the basic technology of industry of other parts As time passes, we have been facing an diff...
A various shearing operation including a machine, a automotive, electricity, electronics industry,a space and aviation industry are a very importance method which can be produce a great much of quantity as on the basic technology of industry of other parts As time passes, we have been facing an difficult circumstance which is developing skill and depend on incoming from other country, because industrial goods are demanded to be have a more precision and high a quality through a various goods and a little production and using new material, specially because of complex shape, mechanical properties and the condition which is more exact demanding, the shortage technology of fine blanking shearing operation and more too expensive units using normal press (160 ton), fine blanking die was placed and teared edge and sheared edges was to be analyzed on the changing rate of productive speed which can have a influence to the prime cost of productivity, and the force of (v_ring) stinger ring which is forming on steel sheets under this study of experiments the used steel sheet on study experiment is performed with steel sheet 3.0t (SPCC 1 for drawing), which are composed with max stress 21.68, stress, strain 41.33%, this sheet is consist of structure which was contained with Ferite structure, soft structure by the results of experiments. when force of v_ring is sheared operation, an effective shear edge are in crseed after limited of steel sheet and harden clamping, using die cusion pin with press force which apply for normal press unit, adjusting 139.74 in this study, when shear velocity fixed with 6.4m /min, the feed rate of stinger ring become to be 97.67 % and the most effective shear edge could be obtained. also depending the result of three experiments, size of shear edge was sheared 87.22% from 1.5 mm, 89.53% from 2.0 mm, 86.08% from 2.5%. and also under changing v type of stinger ring angle, effective shear edge was shown as 85.65% from outer 30 degrees to range inner 45 degree, was shown as 87.38% from outer 45 degrees to range inner 45 degree, was shown as 89.81% from outer 45 degrees to range inner 30 degree, and the spread of shear edge was to be analyzed apply for angle and former used one under condition of three way, 6.4m/min, 10m/min, 16m/min in the shearing speed which is influnced on productivity. example one the result of test are showned that effective shearing edge could be analyzed as 85.66% under the condition of 6.4m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example two the result of test are showned that effective shearing edge could be analyzed as 85.40% under the condition of 10.0m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example three the result of test are showned that effective shearing edge could be analyzed as 87.11% under the condition of 16.0m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example four the result of test are showned that effective shearing edge could be analyzed as 87.38% under the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example five the result of test are showned that effective shearing edge could be analyzed as 85.76% under the condition of 10.0m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example six the result of test are showned that effective shearing edge could be analyzed as 85.04% under the condition of 16.0m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example seven the result of test are showned that effective shearing edge could be analyzed as 89.81% under the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. example eight the result of test are showned that effective shearing edge could be analyzed as 87.12% under the condition of 10.0m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. example nine the result of test are showned that effective shearing edge could be analyzed as 86.61% under the condition of 16.0m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. conclusion during make a change of tested result, effective shearing edge could be analyzed as 91.77% in case the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree, on the condition of the v ring distence 2.0mm if shearing velocity is quick, it is recognized that effective shearing area is more minimize
A various shearing operation including a machine, a automotive, electricity, electronics industry,a space and aviation industry are a very importance method which can be produce a great much of quantity as on the basic technology of industry of other parts As time passes, we have been facing an difficult circumstance which is developing skill and depend on incoming from other country, because industrial goods are demanded to be have a more precision and high a quality through a various goods and a little production and using new material, specially because of complex shape, mechanical properties and the condition which is more exact demanding, the shortage technology of fine blanking shearing operation and more too expensive units using normal press (160 ton), fine blanking die was placed and teared edge and sheared edges was to be analyzed on the changing rate of productive speed which can have a influence to the prime cost of productivity, and the force of (v_ring) stinger ring which is forming on steel sheets under this study of experiments the used steel sheet on study experiment is performed with steel sheet 3.0t (SPCC 1 for drawing), which are composed with max stress 21.68, stress, strain 41.33%, this sheet is consist of structure which was contained with Ferite structure, soft structure by the results of experiments. when force of v_ring is sheared operation, an effective shear edge are in crseed after limited of steel sheet and harden clamping, using die cusion pin with press force which apply for normal press unit, adjusting 139.74 in this study, when shear velocity fixed with 6.4m /min, the feed rate of stinger ring become to be 97.67 % and the most effective shear edge could be obtained. also depending the result of three experiments, size of shear edge was sheared 87.22% from 1.5 mm, 89.53% from 2.0 mm, 86.08% from 2.5%. and also under changing v type of stinger ring angle, effective shear edge was shown as 85.65% from outer 30 degrees to range inner 45 degree, was shown as 87.38% from outer 45 degrees to range inner 45 degree, was shown as 89.81% from outer 45 degrees to range inner 30 degree, and the spread of shear edge was to be analyzed apply for angle and former used one under condition of three way, 6.4m/min, 10m/min, 16m/min in the shearing speed which is influnced on productivity. example one the result of test are showned that effective shearing edge could be analyzed as 85.66% under the condition of 6.4m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example two the result of test are showned that effective shearing edge could be analyzed as 85.40% under the condition of 10.0m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example three the result of test are showned that effective shearing edge could be analyzed as 87.11% under the condition of 16.0m/min on the v ring angle ranging from outside 30 degrees to inside 45 degree. example four the result of test are showned that effective shearing edge could be analyzed as 87.38% under the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example five the result of test are showned that effective shearing edge could be analyzed as 85.76% under the condition of 10.0m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example six the result of test are showned that effective shearing edge could be analyzed as 85.04% under the condition of 16.0m/min on the v ring angle ranging from outside 45 degrees to inside 45 degree. example seven the result of test are showned that effective shearing edge could be analyzed as 89.81% under the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. example eight the result of test are showned that effective shearing edge could be analyzed as 87.12% under the condition of 10.0m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. example nine the result of test are showned that effective shearing edge could be analyzed as 86.61% under the condition of 16.0m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree. conclusion during make a change of tested result, effective shearing edge could be analyzed as 91.77% in case the condition of 6.4m/min on the v ring angle ranging from outside 45 degrees to inside 30 degree, on the condition of the v ring distence 2.0mm if shearing velocity is quick, it is recognized that effective shearing area is more minimize
※ AI-Helper는 부적절한 답변을 할 수 있습니다.