셀룰로오스 나노복합체 필름의 특성연구 장 서 원 금오공과대학교 일반대학원 고분자공학과 요약 용액 블렌딩 법을 통해 세가지 다른 충전제를 사용하여 셀룰로오스 블렌드 필름을 만들고 각각의 기계적 성질과 모폴로지를 비교했다. 폴리(비닐 알코올) (PVA), 폴리(비닐 알코올-에틸렌) (EVOH) 그리고 폴리(아크릴산-말레산) (...
셀룰로오스 나노복합체 필름의 특성연구 장 서 원 금오공과대학교 일반대학원 고분자공학과 요약 용액 블렌딩 법을 통해 세가지 다른 충전제를 사용하여 셀룰로오스 블렌드 필름을 만들고 각각의 기계적 성질과 모폴로지를 비교했다. 폴리(비닐 알코올) (PVA), 폴리(비닐 알코올-에틸렌) (EVOH) 그리고 폴리(아크릴산-말레산) (PAM) 등이 세가지 충전제로 사용되었다. 각 블렌드 필름의 물성들은 첨가된 충전제의 양에 따라 다양하게 변하였다. 30 무게 %의 PVA/셀룰로오스 블렌드 필름의 최대 인장 강도가 가장 높은 값을 가졌으며 40 무게 %가 되면 감소했다. EVOH/셀룰로오스와 PAM/셀룰로오스 블렌드 필름은 EVOH와 PAM이 각각 20 무게 % 포함되었을 때 가장 높았고, 그 이상이 되면 역시 감소했다. 초기 탄성률 값에서도 비슷한 결과를 보였는데, 세가지 블렌드 필름 중에서 PVA를 포함한 필름이 가장 높은 기계적 성질을 가졌다. 서로 다른 두가지 유기화 점토를 이용한 셀룰로오스 나노복합체 필름의 기계적 성질, 모폴로지, 가스 투과성 등을 조사하였다. 유기화 점토로는 도데실 트리페닐 포스포니움-마이카 (C12PPh-Mica)와 헥사데실-마이카 (C16-Mica)가 각각 사용되었다. 소량의 유기화 점토 (0 - 7 무게 %)의 첨가로도 셀룰로오스의 성질을 증가시키기에 충분하였으며, 인장 강도의 경우에는 C16-Mica가 C12PPh-Mica에 비해 보다 적은 양으로도 효과를 보여주었으나, 초기 탄성률의 경우에는 C12PPh-Mica가 보다 효과적이었다. 가스 투과성의 경우 C16- Mica를 사용한 경우에 C12PPh-Mica를 사용하였을 때보다 산소 차단성이 우수한 결과를 얻을 수 있었다. PVA가 30 무게 % 포함된 블렌드된 셀룰로오스 나노복합체 필름을 제조한 후에 각 기계적 성질을 유기화 점토의 양에 따라 조사하여 조사하여 순수한 셀룰로오스 나노복합체 필름과 비교하였다. 순수한 셀룰로오스 나노복합체의 경우에는 기계적 성질이 5 무게 % 점토를 첨가했을 때 가장 높은 값을 가졌으며, 소량의 점토만으로도 순수한 셀룰로오스 보다 높은 기계적 성질을 나타내었다. PVA를 포함한 셀룰로오스 블렌드 (PVA/Cellulose (w/w = 30/70))의 나노복합체 필름의 경우에는 유기화 점토의 첨가된 양이 1에서 5 무게 %까지 증가해도 기계적 물성은 오히려 일정하게 감소하였다.
셀룰로오스 나노복합체 필름의 특성연구 장 서 원 금오공과대학교 일반대학원 고분자공학과 요약 용액 블렌딩 법을 통해 세가지 다른 충전제를 사용하여 셀룰로오스 블렌드 필름을 만들고 각각의 기계적 성질과 모폴로지를 비교했다. 폴리(비닐 알코올) (PVA), 폴리(비닐 알코올-에틸렌) (EVOH) 그리고 폴리(아크릴산-말레산) (PAM) 등이 세가지 충전제로 사용되었다. 각 블렌드 필름의 물성들은 첨가된 충전제의 양에 따라 다양하게 변하였다. 30 무게 %의 PVA/셀룰로오스 블렌드 필름의 최대 인장 강도가 가장 높은 값을 가졌으며 40 무게 %가 되면 감소했다. EVOH/셀룰로오스와 PAM/셀룰로오스 블렌드 필름은 EVOH와 PAM이 각각 20 무게 % 포함되었을 때 가장 높았고, 그 이상이 되면 역시 감소했다. 초기 탄성률 값에서도 비슷한 결과를 보였는데, 세가지 블렌드 필름 중에서 PVA를 포함한 필름이 가장 높은 기계적 성질을 가졌다. 서로 다른 두가지 유기화 점토를 이용한 셀룰로오스 나노복합체 필름의 기계적 성질, 모폴로지, 가스 투과성 등을 조사하였다. 유기화 점토로는 도데실 트리페닐 포스포니움-마이카 (C12PPh-Mica)와 헥사데실-마이카 (C16-Mica)가 각각 사용되었다. 소량의 유기화 점토 (0 - 7 무게 %)의 첨가로도 셀룰로오스의 성질을 증가시키기에 충분하였으며, 인장 강도의 경우에는 C16-Mica가 C12PPh-Mica에 비해 보다 적은 양으로도 효과를 보여주었으나, 초기 탄성률의 경우에는 C12PPh-Mica가 보다 효과적이었다. 가스 투과성의 경우 C16- Mica를 사용한 경우에 C12PPh-Mica를 사용하였을 때보다 산소 차단성이 우수한 결과를 얻을 수 있었다. PVA가 30 무게 % 포함된 블렌드된 셀룰로오스 나노복합체 필름을 제조한 후에 각 기계적 성질을 유기화 점토의 양에 따라 조사하여 조사하여 순수한 셀룰로오스 나노복합체 필름과 비교하였다. 순수한 셀룰로오스 나노복합체의 경우에는 기계적 성질이 5 무게 % 점토를 첨가했을 때 가장 높은 값을 가졌으며, 소량의 점토만으로도 순수한 셀룰로오스 보다 높은 기계적 성질을 나타내었다. PVA를 포함한 셀룰로오스 블렌드 (PVA/Cellulose (w/w = 30/70))의 나노복합체 필름의 경우에는 유기화 점토의 첨가된 양이 1에서 5 무게 %까지 증가해도 기계적 물성은 오히려 일정하게 감소하였다.
Characterizations of Cellulose Nanocomposite Films Seo-Won Jang Department of Polymer Science and Engineering, Graduate School Kumoh National Institute of Technology Abstract Polyblends of Cellulose with three different fillers are compared with their mechanical properties, and morphologies. Poly(vi...
Characterizations of Cellulose Nanocomposite Films Seo-Won Jang Department of Polymer Science and Engineering, Graduate School Kumoh National Institute of Technology Abstract Polyblends of Cellulose with three different fillers are compared with their mechanical properties, and morphologies. Poly(vinyl alcohol) (PVA), poly(vinyl alcohol-co-ethylene) (EVOH), and poly(acrylic acid-co-maleic acid) (PAM) were used as fillers in the formation of Cellulose blend films with solution blending. The variations of their properties with various filler contents in the polymer matrix are discussed. For the PVA/Cellulose blend, the ultimate tensile strength showed a maximum value at the 30 wt % level of Cellulose in the blend, and then it decreased when the Cellulose content was increased up to 40 wt %. On the other hand, the EVOH/ Cellulose and PAM/Cellulose blends showed a maximum value at the 20 wt % Cellulose loading and then it decreased with increasing filler contents in the ultimate tensile strength. Initial modulus also show similar trend at a critical content of filler. The blends with PVA showed the highest tensile properties of the three blend systems. The mechanical properties, morphologies, and gas barriers of nano- composite films of Cellulose with two different organoclays are compared. Dodecyltriphenylphosphonium-mica (C12PPh-Mica) and hexadecyl-mica (C16 -Mica) were used as reinforcing fillers in the fabrication of the Cellulose hybrid films. Even polymers with low organoclay contents (1?7 wt %) were found to exhibit much higher strength and modulus values than pure Cellulose. The addition of C12PPh-Mica was more effective than that of C16-Mica with regards to the initial tensile modulus, whereas the addition of C16-Mica was more effective than that of C12PPh-Mica with regards to the gas barrier of the Cellulose matrix. PVA/Cellulose blended nanocomposite films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium?mica (C12PPh-Mica) as the organoclay. The variations of the mechanical tensile properties of the hybrids with the organoclay content were examined. The mechanical tensile properties of the PVA/Cellulose (w/w = 30/70) blended hybrid films were found to decrease linearly with increases in organoclay content from 1 to 5 wt %.
Characterizations of Cellulose Nanocomposite Films Seo-Won Jang Department of Polymer Science and Engineering, Graduate School Kumoh National Institute of Technology Abstract Polyblends of Cellulose with three different fillers are compared with their mechanical properties, and morphologies. Poly(vinyl alcohol) (PVA), poly(vinyl alcohol-co-ethylene) (EVOH), and poly(acrylic acid-co-maleic acid) (PAM) were used as fillers in the formation of Cellulose blend films with solution blending. The variations of their properties with various filler contents in the polymer matrix are discussed. For the PVA/Cellulose blend, the ultimate tensile strength showed a maximum value at the 30 wt % level of Cellulose in the blend, and then it decreased when the Cellulose content was increased up to 40 wt %. On the other hand, the EVOH/ Cellulose and PAM/Cellulose blends showed a maximum value at the 20 wt % Cellulose loading and then it decreased with increasing filler contents in the ultimate tensile strength. Initial modulus also show similar trend at a critical content of filler. The blends with PVA showed the highest tensile properties of the three blend systems. The mechanical properties, morphologies, and gas barriers of nano- composite films of Cellulose with two different organoclays are compared. Dodecyltriphenylphosphonium-mica (C12PPh-Mica) and hexadecyl-mica (C16 -Mica) were used as reinforcing fillers in the fabrication of the Cellulose hybrid films. Even polymers with low organoclay contents (1?7 wt %) were found to exhibit much higher strength and modulus values than pure Cellulose. The addition of C12PPh-Mica was more effective than that of C16-Mica with regards to the initial tensile modulus, whereas the addition of C16-Mica was more effective than that of C12PPh-Mica with regards to the gas barrier of the Cellulose matrix. PVA/Cellulose blended nanocomposite films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium?mica (C12PPh-Mica) as the organoclay. The variations of the mechanical tensile properties of the hybrids with the organoclay content were examined. The mechanical tensile properties of the PVA/Cellulose (w/w = 30/70) blended hybrid films were found to decrease linearly with increases in organoclay content from 1 to 5 wt %.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.