본 논문은 누전의 원인과 전기화재의 상관관계 연구를 위해 누전이 발생하는 원리와 화재로 확대되는 경우를 알아보았고, 절연저항계를 이용한 절연점검, 절연측정시험을 비롯한 누전차단기 작동 시험을 하여 누전차단기의 효율성도 알아보았다.
누전검출과 입증을 위해 정전용량충전전류, 흡수전류, 전도전류로 결정되는 절연저항을 설명하였고, 절연시험 방법으로 Spot Reading법과 Short Time법, 시간저항법, 단계저항법을 설명하였으나 Spot Reading법으로 절연저항시험을 실시하였다.
절연이 완벽한 전선로에 메거(절연저항계)를 이용한 절연저항 시험을 할 경우, 절연저항이 가장 큰 ∞(0L)값이 검출되는 것을 가정하여 실험하였으나 실제 사용하는 배선에서는 ∞(0L)값이 나오는 것은 어렵다는 것을 확인 할 수 있었다. 그러므로 누전예방을 위해 절연저항값이 작은 회로나 기기가 발견된다면 누전이 되는 부분을 찾아서 빠르게 수리하여 전기화재를 미연에 방지하는 것이 최선책임을 재인식하였다.
전기화재의 발생요인들은 단락, 과부하, 누전지락, 접촉불량, ...
본 논문은 누전의 원인과 전기화재의 상관관계 연구를 위해 누전이 발생하는 원리와 화재로 확대되는 경우를 알아보았고, 절연저항계를 이용한 절연점검, 절연측정시험을 비롯한 누전차단기 작동 시험을 하여 누전차단기의 효율성도 알아보았다.
누전검출과 입증을 위해 정전용량충전전류, 흡수전류, 전도전류로 결정되는 절연저항을 설명하였고, 절연시험 방법으로 Spot Reading법과 Short Time법, 시간저항법, 단계저항법을 설명하였으나 Spot Reading법으로 절연저항시험을 실시하였다.
절연이 완벽한 전선로에 메거(절연저항계)를 이용한 절연저항 시험을 할 경우, 절연저항이 가장 큰 ∞(0L)값이 검출되는 것을 가정하여 실험하였으나 실제 사용하는 배선에서는 ∞(0L)값이 나오는 것은 어렵다는 것을 확인 할 수 있었다. 그러므로 누전예방을 위해 절연저항값이 작은 회로나 기기가 발견된다면 누전이 되는 부분을 찾아서 빠르게 수리하여 전기화재를 미연에 방지하는 것이 최선책임을 재인식하였다.
전기화재의 발생요인들은 단락, 과부하, 누전지락, 접촉불량, 반 단선 등이 있고 이 중 단락과 과부하는 누전으로 발생하는 것이 대부분이다.
누전을 예방하기 위해 누전차단기 설치가 의무화 됐지만 미세전류에는 제대로 동작하지가 않아 미세전류도 차단할 수 있는 누전 차단기의 적용에 대하여 검토할 필요가 있다.
단락은 주울열이 주위의 물질들을 점진적으로 건조 또는 탄화시켜 화재가 발생한다. 그러므로 철저한 설계, 규정에 따른 시공을 해야 한다. 과전류방지를 위해 전선에서는 절연피복의 파괴가 없도록 전선이나 기기배선의 허용전류를 지키도록 하여야 한다.
결국 누전의 원인은 절연의 정도와 환경에 따라 전기화재와 매우 깊은 관계가 있으며 그 단초가 됨을 알았다. 따라서 누전발생감소를 위하여 행정관서의 소방안전관리 제도의 보완, 설계사의 표준설계, 완벽한 시공업체, 사용자에 대한 안전교육 실시 등으로 피드백 시스템을 구축할 필요가 있다.
본 논문은 누전의 원인과 전기화재의 상관관계 연구를 위해 누전이 발생하는 원리와 화재로 확대되는 경우를 알아보았고, 절연저항계를 이용한 절연점검, 절연측정시험을 비롯한 누전차단기 작동 시험을 하여 누전차단기의 효율성도 알아보았다.
누전검출과 입증을 위해 정전용량 충전전류, 흡수전류, 전도전류로 결정되는 절연저항을 설명하였고, 절연시험 방법으로 Spot Reading법과 Short Time법, 시간저항법, 단계저항법을 설명하였으나 Spot Reading법으로 절연저항시험을 실시하였다.
절연이 완벽한 전선로에 메거(절연저항계)를 이용한 절연저항 시험을 할 경우, 절연저항이 가장 큰 ∞(0L)값이 검출되는 것을 가정하여 실험하였으나 실제 사용하는 배선에서는 ∞(0L)값이 나오는 것은 어렵다는 것을 확인 할 수 있었다. 그러므로 누전예방을 위해 절연저항값이 작은 회로나 기기가 발견된다면 누전이 되는 부분을 찾아서 빠르게 수리하여 전기화재를 미연에 방지하는 것이 최선책임을 재인식하였다.
전기화재의 발생요인들은 단락, 과부하, 누전지락, 접촉불량, 반 단선 등이 있고 이 중 단락과 과부하는 누전으로 발생하는 것이 대부분이다.
누전을 예방하기 위해 누전차단기 설치가 의무화 됐지만 미세전류에는 제대로 동작하지가 않아 미세전류도 차단할 수 있는 누전 차단기의 적용에 대하여 검토할 필요가 있다.
단락은 주울열이 주위의 물질들을 점진적으로 건조 또는 탄화시켜 화재가 발생한다. 그러므로 철저한 설계, 규정에 따른 시공을 해야 한다. 과전류방지를 위해 전선에서는 절연피복의 파괴가 없도록 전선이나 기기배선의 허용전류를 지키도록 하여야 한다.
결국 누전의 원인은 절연의 정도와 환경에 따라 전기화재와 매우 깊은 관계가 있으며 그 단초가 됨을 알았다. 따라서 누전발생감소를 위하여 행정관서의 소방안전관리 제도의 보완, 설계사의 표준설계, 완벽한 시공업체, 사용자에 대한 안전교육 실시 등으로 피드백 시스템을 구축할 필요가 있다.
In this paper, we look to know if it is expanded to the principles and fire that leakage occurs because of the correlation of cause and electrical fires of leakage study, insulation inspection using an insulation resistance meter,
and the insulation measurement test beginning with the efficiency of...
In this paper, we look to know if it is expanded to the principles and fire that leakage occurs because of the correlation of cause and electrical fires of leakage study, insulation inspection using an insulation resistance meter,
and the insulation measurement test beginning with the efficiency of the earth leakage breaker earth leakage breaker by the operation test of which were also examined.
Charging current of capacitance for leakage detection and certification, absorption current, describes the insulation resistance which is determined by the conduction current, Spot Reading method and Short Time Act in insulation test method, time of resistance method, the step resistance method the described, but was carried out Spot Reading method insulation resistance test.
If the insulation is the insulation resistance test using a Mega (insulation resistance meter) completely electric line, and the value of the largest ∞ insulation resistance (0L) was experiments on the assumption to be detected, is actually used : In an wiring, ∞ value of is come out of (0L), it was possible to make sure that it is difficult. Therefore, when the circuit or equipment insulation resistance value is small is found for leakage prevention, and repaired immediately locate the portion where leakage is, is that the re-recognize the best responsibility be prevented electrical fires was.
Cause of electrical fire, paragraphs, overload, short circuit, ground fault, poor contact, include semi-disconnected, of the paragraph and overload is most likely to occur in a short circuit manner.
To prevent short circuit, the earth leakage breaker installations are obliged, micro current is necessary to develop an earth leakage circuit breaker that can also be cut off a small current without operating normally.
Paragraph, Joule heat occurs stepwise drying or to carbonize the surrounding material. Therefore, thorough design, it is necessary to the construction pursuant. The wire for over-current protection, it must be to protect the allowable current and apparatus wiring so that there is no breakdown of insulation.
Cause eventually leakage, depending on the degree and the environment of the insulation, there is a very close relationship with electrical fires, was found to be its beginning. Therefore, in order to decrease the occurrence of leakage, complement of fire safety management system of administrative offices, the standard design of the architect, the perfect contractor, it is necessary to build a feedback system to and implementation of safety education of users.
In this paper, we look to know if it is expanded to the principles and fire that leakage occurs because of the correlation of cause and electrical fires of leakage study, insulation inspection using an insulation resistance meter,
and the insulation measurement test beginning with the efficiency of the earth leakage breaker earth leakage breaker by the operation test of which were also examined.
Charging current of capacitance for leakage detection and certification, absorption current, describes the insulation resistance which is determined by the conduction current, Spot Reading method and Short Time Act in insulation test method, time of resistance method, the step resistance method the described, but was carried out Spot Reading method insulation resistance test.
If the insulation is the insulation resistance test using a Mega (insulation resistance meter) completely electric line, and the value of the largest ∞ insulation resistance (0L) was experiments on the assumption to be detected, is actually used : In an wiring, ∞ value of is come out of (0L), it was possible to make sure that it is difficult. Therefore, when the circuit or equipment insulation resistance value is small is found for leakage prevention, and repaired immediately locate the portion where leakage is, is that the re-recognize the best responsibility be prevented electrical fires was.
Cause of electrical fire, paragraphs, overload, short circuit, ground fault, poor contact, include semi-disconnected, of the paragraph and overload is most likely to occur in a short circuit manner.
To prevent short circuit, the earth leakage breaker installations are obliged, micro current is necessary to develop an earth leakage circuit breaker that can also be cut off a small current without operating normally.
Paragraph, Joule heat occurs stepwise drying or to carbonize the surrounding material. Therefore, thorough design, it is necessary to the construction pursuant. The wire for over-current protection, it must be to protect the allowable current and apparatus wiring so that there is no breakdown of insulation.
Cause eventually leakage, depending on the degree and the environment of the insulation, there is a very close relationship with electrical fires, was found to be its beginning. Therefore, in order to decrease the occurrence of leakage, complement of fire safety management system of administrative offices, the standard design of the architect, the perfect contractor, it is necessary to build a feedback system to and implementation of safety education of users.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.