본 연구에서는 전남 일대 3개소 염전 생산과정 저수지, 1차 증발지, 2차 증발지, 함수창고의 염수에서 미세플라스틱의 존재유무를 확인하고, 천일염 생산에 사용되는 염수에 인위적으로 제조한 미세플라스틱을 첨가한 후 50 μm Fiber filter(FF), 5, 10, 20 μm Star plated filter(...
본 연구에서는 전남 일대 3개소 염전 생산과정 저수지, 1차 증발지, 2차 증발지, 함수창고의 염수에서 미세플라스틱의 존재유무를 확인하고, 천일염 생산에 사용되는 염수에 인위적으로 제조한 미세플라스틱을 첨가한 후 50 μm Fiber filter(FF), 5, 10, 20 μm Star plated filter(SF), 6 μm Paper disk filter(PF), 5 μm Polypropylene disk filter(PPF)들을 이용하여 여과된 염수의 미세플라스틱 저감화를 관찰하였다. 또한 필터장치들을 이용하여 여과된 염수로 제조된 천일염에서 미세플라스틱이 얼마나 영향을 주는지 분석하였다. 저수지, 1차 증발지, 2차 증발지, 함수창고의 염수에서 미세플라스틱의 여부를 분석한 결과 UV-light와 형광현미경에 의해 미세플라스틱으로 추측 되는 입자들을 육안으로도 확인했다. 그리고 Ranman spectroscopy를 이용하여 Polypropylene(PP), polystyrene(PS)으로 추측되는 입자를 선택하여 입자의 Spectrum을 Raman에 저장되어 있는 Polypropylene Spectrum과 Polypropylene Spectrum을 이용하여 서로를 매치하여 Polypropylene(PP), Polystyrene(PS)인 것을 확인하였다. Particle counter analysis에서 Control(867개)과 비교하여 필터장치 모두 미세플라스틱을 감소시키는 것을 확인했으며 6 μm Paper disk filter(PF)가 12개(98.61 %)로 가장 높게 감소되었으며, 그 다음으로는 5 μm star plated filter(SF)가 51개(94.07 %)로 2번째로 높게 감소되는 것을 확인할 수 있었지만 20 μm Star plated filter(SF)에서 107개(87.66 %), 5 μm Polypropylene disk filter(PPF)에서 271개(68.74 %)로 낮게 감소되는 것을 확인하였다. UV-light와 형광현미경을 사용하여 육안으로 볼 때 Control과 비교하여 전체적으로 미세플라스틱이 감소되었지만 20 μm Star plated filter(SF)와 5 μm Polypropylene disk filter(PPF)에서 미세플라스틱 입자 의 수가 많은 것을 볼 수 있었다. 필터장치를 이용하여 생산된 천일염에서 색도 및 미네랄 함량의 변화를 분석한 결과 색도는 Control과 비교하여 필터 장치에 의해 생성된 천일염들은 Control보다 낮은 L값을 나타냈으며 a값, b값은 유의한 차이를 나타내지 않았다. 이는 Control에 들어있는 미세플라스틱에서 높은 L값을 나타내는 것으로 판단되며 필터 장치에 의해 생성된 천일염에서는 미세플라스틱이 감소되었기 때문에 L값이 낮게 나타나는 것으로 판단된다. 미네랄 함량을 비교한 결과 Mg, Na, Cu 함량은 유의한 차이를 나타내지 않았다. K 함량은 Control과 비교하여 10 μm Star plated filter(SF)와 6 μm Paper disk filter(PF)에서 K 함량이 높았으며 다른 필터 장치들에 의해 생산된 천일염은 유의한 차이는 없는 것으로 나타났다. Ca, Fe 함량은 Star plated filter(SF)에 의해 생산된 천일염이 높은 함량을 나타냈다. UV-light와 형광현미경에 의해 미세플라스틱으로 추측 되는 입자들을 육안으로도 관찰한 결과 필터장치를 이용하여 생성된 천일염들 모두 Control과 비교하여 미세플라스틱이 감소하는 것을 육안으로 확인하였다. Cellulose nitrate membrane에서 인위적으로 첨가된 Styrofoam(ST)은 Ranman spectroscopy으로 확인할 수 없었다. 20 μm Star plated filter(SF)와 5 μm Polypropylene disk filter(PPF)를 이용하여 생산된 천일염에서 미세플라스틱의 비율은 다른 필터들을 이용하여 생산된 천일염과 비교하여 높게 나타나는 것을 확인했다. 본 연구를 통해 필터 장치는 천일염 제조 공정에 존재하는 미세플라스틱을 감소시키는데 효과적인 것을 보여주었으며 이 연구에서 사용된 필터 시스템은 사회적으로 논란이 되고 있는 미세플라스틱의 감소와 천일염의 안전을 위한 효과적인 도구가 될 것으로 믿어진다.
본 연구에서는 전남 일대 3개소 염전 생산과정 저수지, 1차 증발지, 2차 증발지, 함수창고의 염수에서 미세플라스틱의 존재유무를 확인하고, 천일염 생산에 사용되는 염수에 인위적으로 제조한 미세플라스틱을 첨가한 후 50 μm Fiber filter(FF), 5, 10, 20 μm Star plated filter(SF), 6 μm Paper disk filter(PF), 5 μm Polypropylene disk filter(PPF)들을 이용하여 여과된 염수의 미세플라스틱 저감화를 관찰하였다. 또한 필터장치들을 이용하여 여과된 염수로 제조된 천일염에서 미세플라스틱이 얼마나 영향을 주는지 분석하였다. 저수지, 1차 증발지, 2차 증발지, 함수창고의 염수에서 미세플라스틱의 여부를 분석한 결과 UV-light와 형광현미경에 의해 미세플라스틱으로 추측 되는 입자들을 육안으로도 확인했다. 그리고 Ranman spectroscopy를 이용하여 Polypropylene(PP), polystyrene(PS)으로 추측되는 입자를 선택하여 입자의 Spectrum을 Raman에 저장되어 있는 Polypropylene Spectrum과 Polypropylene Spectrum을 이용하여 서로를 매치하여 Polypropylene(PP), Polystyrene(PS)인 것을 확인하였다. Particle counter analysis에서 Control(867개)과 비교하여 필터장치 모두 미세플라스틱을 감소시키는 것을 확인했으며 6 μm Paper disk filter(PF)가 12개(98.61 %)로 가장 높게 감소되었으며, 그 다음으로는 5 μm star plated filter(SF)가 51개(94.07 %)로 2번째로 높게 감소되는 것을 확인할 수 있었지만 20 μm Star plated filter(SF)에서 107개(87.66 %), 5 μm Polypropylene disk filter(PPF)에서 271개(68.74 %)로 낮게 감소되는 것을 확인하였다. UV-light와 형광현미경을 사용하여 육안으로 볼 때 Control과 비교하여 전체적으로 미세플라스틱이 감소되었지만 20 μm Star plated filter(SF)와 5 μm Polypropylene disk filter(PPF)에서 미세플라스틱 입자 의 수가 많은 것을 볼 수 있었다. 필터장치를 이용하여 생산된 천일염에서 색도 및 미네랄 함량의 변화를 분석한 결과 색도는 Control과 비교하여 필터 장치에 의해 생성된 천일염들은 Control보다 낮은 L값을 나타냈으며 a값, b값은 유의한 차이를 나타내지 않았다. 이는 Control에 들어있는 미세플라스틱에서 높은 L값을 나타내는 것으로 판단되며 필터 장치에 의해 생성된 천일염에서는 미세플라스틱이 감소되었기 때문에 L값이 낮게 나타나는 것으로 판단된다. 미네랄 함량을 비교한 결과 Mg, Na, Cu 함량은 유의한 차이를 나타내지 않았다. K 함량은 Control과 비교하여 10 μm Star plated filter(SF)와 6 μm Paper disk filter(PF)에서 K 함량이 높았으며 다른 필터 장치들에 의해 생산된 천일염은 유의한 차이는 없는 것으로 나타났다. Ca, Fe 함량은 Star plated filter(SF)에 의해 생산된 천일염이 높은 함량을 나타냈다. UV-light와 형광현미경에 의해 미세플라스틱으로 추측 되는 입자들을 육안으로도 관찰한 결과 필터장치를 이용하여 생성된 천일염들 모두 Control과 비교하여 미세플라스틱이 감소하는 것을 육안으로 확인하였다. Cellulose nitrate membrane에서 인위적으로 첨가된 Styrofoam(ST)은 Ranman spectroscopy으로 확인할 수 없었다. 20 μm Star plated filter(SF)와 5 μm Polypropylene disk filter(PPF)를 이용하여 생산된 천일염에서 미세플라스틱의 비율은 다른 필터들을 이용하여 생산된 천일염과 비교하여 높게 나타나는 것을 확인했다. 본 연구를 통해 필터 장치는 천일염 제조 공정에 존재하는 미세플라스틱을 감소시키는데 효과적인 것을 보여주었으며 이 연구에서 사용된 필터 시스템은 사회적으로 논란이 되고 있는 미세플라스틱의 감소와 천일염의 안전을 위한 효과적인 도구가 될 것으로 믿어진다.
In this study, the existence of microplastic in salt water of reservoir, primary evaporating pond, secondary evaporating pond, and ephemeral saline reservoir during the solar salt production process was investigated at three solar salt production sites in Chonnam province. After adding artificially ...
In this study, the existence of microplastic in salt water of reservoir, primary evaporating pond, secondary evaporating pond, and ephemeral saline reservoir during the solar salt production process was investigated at three solar salt production sites in Chonnam province. After adding artificially prepared microplastics to brine used for the production of solar salt, 50 μm fiber filter(FF), 5, 10 and 20 μm star plated filter(SF), 6 μm paper disk filter(PF), and 5 μm polypropylene disk filter(PPF) were used to observe the reduction of microplastic in the brine for solar salt. Also, the reduction effect of microplastics on the solar salt produced with filtered brine water using filter devices was analyzed. The presence and analysis of microplastics in the reservoir, primary evaporating pond, secondary evaporating pond, and ephemeral saline reservoir was confirmed by UV-light and fluorescence microscopy. Then, the particles assumed to be polypropylene(PP) and polystyrene(PS) were selected by using Raman spectroscopy. The spectra of the particles were confirmed to be polypropylene(PP) and polystyrene(PS) by matching the spectrum stored in Raman spectroscopy. As a result, in the particle counter analysis, it was confirmed that all of the filter devices were reduced in comparison with the control (867 pieces). The 6 μm paper disk filter(PF) was the highest with 12 pieces(98.61 %), followed by the 5 μm star plated filter(SF) with 51 pieces(94.07 %), the second highest. But it showed that the 20 μm star plated filter(SF) decreased from 867 to 107 pieces(87.66 %), and the 5 μm polypropylene disk filter(PPF) to 271 pieces(68.74 %). The overall microplastics were reduced by filteration, but the numbers of microplastic particles by visual inspection using UV-light and fluorescence microscopy were large in the 20 μm star plated filter (SF) and 5 μm polypropylene disk filter(PPF) than paper disk filter(PF). As a result of analyzing the change of chromaticity and mineral content in the solar salt produced by the filter device, the chromaticity showed a lower L value than the control, and the a value and the b value did not show any significant difference. The high L value at the control is estimated to be due to microplastic in it. As a result, low L values are shown in the sample through the filter device. In mineral contents, Mg, Na and Cu contents did not show any significant difference among samples. The K content was higher in the 10 μm star plated filter(SF) and 6 μm paper disk filter(PF) than in the control, and there was no significant difference in the K content produced solar salt by other filter devices. The contents of Ca and Fe showed high contents of solar salt produced by star plated filter (SF). As a result of microscopic observation of the microplastic particles by UV-light and fluorescence microscopy, it was observed that the reduction of microplastics the solar salts produced by the filter device was visually observed in comparison with control. The artificially added styrofoam(ST) filtered by the cellulose nitrate membrane could not be identified by Raman spectroscopy. The ratio of polypropylene (PP) in the solar salt produced by using 20 μm star plated filter(SF) and 5 μm polypropylene disk filter(PPF) was higher than that produced by other filters. Through this study, the filter device has been shown to be effective in reducing microplastics present in the manufacturing process to solar salts. It is believed that the filter system used in this study would be effective tool for the reduction of microplastics and the safety of solar salt which are controversial socially.
In this study, the existence of microplastic in salt water of reservoir, primary evaporating pond, secondary evaporating pond, and ephemeral saline reservoir during the solar salt production process was investigated at three solar salt production sites in Chonnam province. After adding artificially prepared microplastics to brine used for the production of solar salt, 50 μm fiber filter(FF), 5, 10 and 20 μm star plated filter(SF), 6 μm paper disk filter(PF), and 5 μm polypropylene disk filter(PPF) were used to observe the reduction of microplastic in the brine for solar salt. Also, the reduction effect of microplastics on the solar salt produced with filtered brine water using filter devices was analyzed. The presence and analysis of microplastics in the reservoir, primary evaporating pond, secondary evaporating pond, and ephemeral saline reservoir was confirmed by UV-light and fluorescence microscopy. Then, the particles assumed to be polypropylene(PP) and polystyrene(PS) were selected by using Raman spectroscopy. The spectra of the particles were confirmed to be polypropylene(PP) and polystyrene(PS) by matching the spectrum stored in Raman spectroscopy. As a result, in the particle counter analysis, it was confirmed that all of the filter devices were reduced in comparison with the control (867 pieces). The 6 μm paper disk filter(PF) was the highest with 12 pieces(98.61 %), followed by the 5 μm star plated filter(SF) with 51 pieces(94.07 %), the second highest. But it showed that the 20 μm star plated filter(SF) decreased from 867 to 107 pieces(87.66 %), and the 5 μm polypropylene disk filter(PPF) to 271 pieces(68.74 %). The overall microplastics were reduced by filteration, but the numbers of microplastic particles by visual inspection using UV-light and fluorescence microscopy were large in the 20 μm star plated filter (SF) and 5 μm polypropylene disk filter(PPF) than paper disk filter(PF). As a result of analyzing the change of chromaticity and mineral content in the solar salt produced by the filter device, the chromaticity showed a lower L value than the control, and the a value and the b value did not show any significant difference. The high L value at the control is estimated to be due to microplastic in it. As a result, low L values are shown in the sample through the filter device. In mineral contents, Mg, Na and Cu contents did not show any significant difference among samples. The K content was higher in the 10 μm star plated filter(SF) and 6 μm paper disk filter(PF) than in the control, and there was no significant difference in the K content produced solar salt by other filter devices. The contents of Ca and Fe showed high contents of solar salt produced by star plated filter (SF). As a result of microscopic observation of the microplastic particles by UV-light and fluorescence microscopy, it was observed that the reduction of microplastics the solar salts produced by the filter device was visually observed in comparison with control. The artificially added styrofoam(ST) filtered by the cellulose nitrate membrane could not be identified by Raman spectroscopy. The ratio of polypropylene (PP) in the solar salt produced by using 20 μm star plated filter(SF) and 5 μm polypropylene disk filter(PPF) was higher than that produced by other filters. Through this study, the filter device has been shown to be effective in reducing microplastics present in the manufacturing process to solar salts. It is believed that the filter system used in this study would be effective tool for the reduction of microplastics and the safety of solar salt which are controversial socially.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.