참고문헌 (18)

1. S. Crutzen and P. Jehenson, 'The correlation between ultrasonic techniques, equipment, defect parameters and inspection performanceeffectiveness', Improving the Effectiveness and Reliability of Non-Destructive Testing, edited by W. E. Gardner, Pergamon Press., pp. 193-224 (1992) 

2. E. Borloo, F. Lakestani and F. Merli, 'PISC II - Parametric study on the effect of ultrasonic characteristics (EEC) on detection, location and sizing,' PISC 1lI Report No. 10 - Final report, Available from Commission of the European Communities, Joint Research Center, Ispra, Italy (July, 1988) 

3. D. E. MacDonald and S. M. Walker, 'Effects of ultrasonic equipment variations on crack length measurements,' EPRl NP - 5485, 1987, Available from EPRl Research Reports Center, PO Box 504901, Palo Alto, CA 94305 

4. G. J. Posakony, 'Experimental analysis of ultrasonic responses from artificial defects,' Materials Evaluation, Vol. 44, No. 13, pp. 1567-1572 (Dec., 1986) 

   상세보기

5. N. F. Haines, S. Cruzen and C. J. Vinehc, 'A review of the major PISC II Round-robin test results,' British Journal of NDT, pp. 411-417 (Nov., 1987) 

6. S. Crutzen, P. Jehenson and E. Borloo, 'The PISC II - RRT Plates and their intended defects', British Journal of NDT, pp. 307- 317 (Sep., 1987) 

7. E. R. Green, 'Worst case defects affecting ultrasonic inspection reliability,' Materials Evaluation, Vol. 47, pp. 1401-1407 (Dec.,1969) 

8. F. V. Ammirato, GEC, Knolls Atomic Power Laboratory, Schenectady, New York, 'The influencing of reference defect geometry, beam angle and frequency on shear wave ultrasonic test sensitivity,' Materials Evaluation, pp. 45-48 (Feb., 1976) 

9. ASME Section XI, Appendix III 

10. M. Manimohan, N. D hanasekaran, R J. Pardikar et aI., 'Reliability of manual ultrasonic testing in boiler and pressure vessels,' Journal of Non-Destructive Evaluation, Vol. 16, No.4, pp. 99-101 (Oct-Dec., 1996) 

11. E. E. Borloo, 'PISC II - Parametric studies, RRT on the measurement of ultrasonic instrument and transducer characteristics (MITC),' International Journal of Pressure Vessels & Piping, Vol. 35, Nos. 1-4 

12. A. B. Wooldridge and R. K. Chapman, 'The Effective use of ultrasonic for defect detection ands sizing in steel components,' Improving the Effectiveness and Reliability of Non-Destructive Testing, Edited by W. E. Gardner, Pergamon Press, Oxford, UK, pp. 87-136 (1992) 

13. B. Watkins, R. W. Errine and K. J. Cowburn, 'The UKAEA defect detection trials,' British Journal of Non-Destructive Evaluation, Vol. 25, No.4 (July, 1983) 

14. J. Krautkramer and H. Krautkramer, 'Ultrasonic testing of materials,' 3rd Edition, Springer-Verlag, Berlin, Germany (1983) 

15. Giuliano Canella, 'Resonance's and effects of couplant layers in ultrasonic contact testing', Materials Evaluation, pp. 61-66 (April, 1973) 

16. Johan Enkrist, Anne Edland and Ola Svenson, 'Operator performance in a blind test piece trial,' Materials Evaluation, Vol. 59, No.4, pp. 531-536 (April, 2001) 

17. R. A. Murgatroyd, H. Serd, S. Crutzen and Van Den Bergh, 'Human Reliability Studies in P1SC Ill,' 10th International Conference on NDE in the Nuclear and Pressure Vessel Industry, Glasgow, UK (June, 1990) 

18. T. T. Taylor, J. C. Spanner, Sh. P. G. Heasler, S. R. Doctor and J. D. Deffenbaugh, 'An evaluation of human reliability in ultrasonic In-service inspection for intergranular stress- corrosion cracks through round-robin testing,' Materials Evaluation, (March, 1989)