최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기韓國地盤工學會論文集 = Journal of the Korean geotechnical society, v.31 no.11, 2015년, pp.5 - 13
서미정 (고려대학교 건축사회환경공학부) , 박종배 (한국토지주택공사 토지주택연구원) , 박용부 (한국토지주택공사 토지주택연구원) , 이종섭 (고려대학교 건축사회환경공학부)
For the bearing capacity evaluation, dynamic pile tests instead of static pile tests have been commonly used in embedded piles, which are known to have low noise and low vibration construction method. The objective of this study is to analyze the bearing capacity and penetration behaviors of embedde...
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
핵심어 | 질문 | 논문에서 추출한 답변 |
---|---|---|
말뚝의 지지력을 산정하기 위해 동재하시험방법을 사용하는 이유는 무어인가? | , 2002). 이 때 말뚝의 지지력을 산정하는 방법으로 동재하시험은 대부분의 현장에서 적용가능하고 경제적이므로 많이 사용된다. 매입말뚝의 마무리 경타는 항타말뚝의 항 타와 동일하게 파동방정식에 근거한 동적해석을 수행할 수 있으며(Im et al. | |
구조물 건축 시 매입말뚝공법을 이용하는 이유는 어떤 문제를 해결하기 위함인가? | 도심지 등의 항타공사로 인한 소음과 지반진동 등의 문제로 매입말뚝공법이 적용되고 있다(Hong et al., 2002). | |
WEAP의 입력조건 중 해머에 관한 조건으로 어떤 요소들을 고려할 수 있는가? | WEAP의 입력조건은 크게 해머, 쿠션, 말뚝, 지반에 관한 조건 등으로 나뉜다. 해머에 관한 조건은 해머의 종류와 해머효율, 해머낙하고 등으로 동재하시험 분석시 가장 큰 영향을 미친다(Kim et al., 2000). |
Cho, C. W. (2010), "Piling Engineering Practice", Engineer Book, Seoul, 744p.
Choi, D.W., Han, B. K., Seo, Y. H., and Cho, S. H. (2002), "A Study on the Improvement of Bearing Capacity Prediction Equation for Auger-drilled Piling", 2002 Fall Geotechnical Engineering, pp.382-389.
Han, J. T., Yoo, M. T., Yang, E. K., and Kim, M. M. (2010), "Evaluation of Particle Size Effect on Dynamic Behavior of Soil-Pile System", Journal of Geotechnical Engineering, Vol.26, No.7, pp.49-58.
Heo, J. H. (2007), "The Study on Measurement of Noise from SIP Steel Pipe Pile and Energy Transfer Rate in Association with the Pile Cushion Material Using a Dynamic Load Test", Thesis for Master's Degree at Chonnam National University, 66p.
Hong, W. P. and Chai, S. G. (2007), "Estimation of Frictional Capacity of SDA Augered Piles in Various Ground", Journal of the Korean Society of Civil Engineers, Vol.27, No.4, pp.279-292.
Im, H. S., Park, Y. B., Park, J. B., Kim, J. S., Han, K. R., and Kim, D. H. (2001), "The Proposal of Quality Improvement Guide and Bearing Capacity Estimation of SIP", Housing & Urban Research Institute, Daejeon, 154p.
Jung, D. W. (2000), "Evaluation of Driving System Efficiency and Driven Pile Capacity Based on Dynamic Pile Load Tests", Journal of Korea Polytechnic University, Vol.5, pp.277-284.
Kim, B. S. (1997), "A Study on the Pile/Soil Correlation of Underground", Journal of the Korea National University of Transportation, Vol.32, No.2, pp.453-462.
Kim, B. T., Lee, S. U., and Kim, Y. S. (1998), "Model Testing on the Behavior of Laterally Loaded Pile in NC Clay Soils", Journal of the Korean Geotechnical Society, Vol.14, No.5, pp.39-52.
Kim, J. D., Hong, J. K., Park, Y. B., Park, J. B., and Song, Y. (1998), "The Manual for Pile Load Test and Analysis of Test Result", Housing & Urban Research Institute, Daejeon, 175p.
Kim, J. D., Im, H. S., Park, Y. B., Park, J. B., and Lee, W. J. (2000), "Determination of the Optimized Driving Force and End Time of Driving for Pile Construction", Housing & Urban Research Institute, Daejeon, 237p.
Kim, J. Y., Lee, C. K., and Heo, Y. (1999), "Comparative Analysis of Bearing Capacity in Driven and Embedded Piles", Journal of Industrial Science and Technology Institute, Vol.13, No.1, pp.129-140.
Kwon, H. J. and Moon, B. S. (1996), "Estimation of the Bearing Capacity of Pile by Static Load Test and Dynamic Load Test in Sangmoo District of Kwangju City", Journal of Industrial Technology Research, Vol.7, pp.17-37.
Lee, C. H., Chung, S. G., and Kim, S. R. (2009), "Applicability of CPT-based Toe Bearing Capacity of PHC Driven Piles", Journal of Geotechnical Engineering, Vol.25, No.12, pp.107-118.
Lee, J. B. (2011), "A Consideration of Theoretical Value and Measured Value about a Formula in Statics of Bored Pile Method", Thesis for Master's Degree at Kwandong University, 44p.
Lee, M. W. and Hong, H. S. (2006), "A Report on the Problems Associated with PDA Testing in Korea", 2006 Spring Geotechnical Engineering Conference, pp.1259-1268.
Lee, W. J., Yoon, K. H., Suk, J. S., and Lee, W. J. (1998), "Evaluation of Bearing Capacity of Piles in Sand Using Pile Driving Analyzer", Journal of Geotechnical Engineering, Vol.13, No.5, pp.145-154.
Linkins, G. and Rausche, F. (2004), "Correlation of CAPWAP with Static Load Tests", Proceedings of the Seventh International Conference on the Application of Stresswave Theory to Piles, pp. 153-165.
Paik, K. and Salgado, R. (2003), "Determination of Bearing Capacity of Open-Ended in Sand", Journal of Geotechnical & Geoenvironmental Engineering, Vol.129, Issue.1, pp.46-57.
Paik, K., Salgado, R., Lee, J., and Kim, B. (2003), "Behavior of Open- and Closed-Ended Piles Driven into Sands", Journal of Geotechnical & Geoenvironmental Engineering, Vol.129, Issue.4, pp.296-306.
Park, J. B., Kim, J. S., Lim, H. S., and Park, Y. B. (2004), "Estimation of Bearing Capacity of SIP Pile by Static & Dynamic Load Test", Journal of Korean Society of Civil Engineers, Vol.2004, No.10, pp.2356-2361.
Randolph, M. F., Dolwin, J., and Beck, R. (1994), "Design of Driven Piles in Sand", Geotechnique, Vol.44, No.3, pp.427-448.
Seo, Y. H., Cho, S. H., Choi, D. W., and Han, B. K. (2003), "A Study on the Optimum Design Guide for Auger-drilled Piling", Journal of Korean Society of Civil Engineers, Vol.51, No.7, pp. 8-16.
Shim, T. S., Joo, S. W., and Choi, S. Y. (1999), "A Study on a Evaluation of Pile Bearing Capacity Using PDA Test", Journal of Construction Technology Research, Vol.19, No.2, pp.1-21.
Yoon, J. Y. (2003), "Evaluation of Ultimate Bearing Capacity on Granular Compaction Pile Considering Varying Stresses in a Ground", Thesis for Master's Degree at Hongik University, 78p.
*원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다.
출판사/학술단체 등이 한시적으로 특별한 프로모션 또는 일정기간 경과 후 접근을 허용하여, 출판사/학술단체 등의 사이트에서 이용 가능한 논문
※ AI-Helper는 부적절한 답변을 할 수 있습니다.