최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기복합신소재구조학회 논문집 = Journal of the Korean Society for Advanced Composite Structures, v.6 no.3, 2015년, pp.32 - 40
나환선 (한국전력공사 전력연구원) , 이현주 (한국전력공사 전력연구원)
The torque shear high strength bolt is clamped normally at the break of pin-tail specified. However, the clamping forces on slip critical connections do not often meet the required tension, as it considerably fluctuates due to torque coefficient dependent on lubricant affected temperature. In this s...
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
핵심어 | 질문 | 논문에서 추출한 답변 |
---|---|---|
TS고력볼트의 KS기준은 언제 제정되었는가? | TS고력볼트의 KS기준은 2003년 제정되었으며, KS F10T, S10T에 해당하는 ASTM F2280이 2006년에 제정되었고, KS F10T에 대한 기술시방서를 비롯하여 관련 기술기준이 정립된 건 국내 외를 살펴봐도 최근 10년 내외에 불과하다. TS고력볼트는 일정한 토크에서 핀테일이 파단되도록 유도된 제품이지만 토크관리 법에 근거하고 있다. | |
본 연구에서 토크전단형 고력볼트에 대한 온도의존성을 검증하기 위한 실내실험의 결과는 어떠한가? | 2) 토크전단형 고력볼트에 대한 온도의존성을 검증하기위해 수행된 실내실험과 현장측정결과를 비교분석하고 통합한 토크계수의 결과는 다음과 같다. 실내실험은 각 온도별로 10개의 시험체로 구성하고 온도구간별 평균 토크계수에 대한 온도구간별 변화 추이는 1℃당 0.13%/℃이었다. | |
TS고력볼트의 문제점은 무엇인가? | 한국과 일본의 경우에는 2000년대 이후 육각머리 고력볼트보다 핀테일이 파단되는 외형적 특성때문에 토크전단형 고력볼트(이하, TS고력 볼트)를 주로 사용하고 있다. TS고력볼트의 경우, 건 설현장의 작업자는 물론 관리감독자조차 TS고력볼트 의 핀테일이 파단되면 적정축력이 도입될 것으로 오해하고 있지만 실제로는 외부환경조건에 따라 볼트 나사산, 와셔에 도포된 윤활유의 점도변화는 물론 이 물질의 부착여부 등 다양한 현장조건에 따라서 토크 계수가 변하고 설계조건에 필요한 축력이 도입되지 못하거나 과도하게 체결될 경우가 종종 발생한다. 위와 같은 문제점이 실제 건설현장에서 얼마나 대두되는지를 사실 확인하거나 검증한 사례는 거의 없다. |
Architectural Institute of Japan (2003), Guidebook on Design and Fabrication of High Strength Bolted Connections, AIJ.
ASTM F 2280-06 (2006), Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150ksi Minimum Tensile Strength, ASTM International, Philadelphia, PA, USA.
ASTM F959M, Standard Specification for Compressible-Washer-Type Direct Tension Indicators for use with Structural Fasteners, ASTM International, Philadelphia, PA, USA.
Bickford, John H.(1990), An Introduction to the Design and Behavior of Bolted Joints, Marcel Dekker Inc., Madison Avenue, New York, NJ.
Khairedin Abdalla, Dimitrios N. Kaziolas, Charalambos C.Baniotopoulos (2011), "Tightening and Loosening Torque of M253 Bolts : Experimental and Analytical Investigation", International Journal of Engineering and Information Sciences, 6(2), pp. 69-83.
Kulak, Geoffrey L.,Fisher, John W., Struik, John H.A.(2001), Guide to Design Criteria for Bolted and Riveted Joints, 2nd Ed., AISC Inc.
Nah, H. S., Lee, H. J., and Choi, S. M. (2014), "Evaluating long-term relaxation of high strength bolts considering coating on slip faying surface"', Steel and Composite Structures, Vol. 16, No. 6, pp. 703-718.
Nah, H. S., Lee, H. J., Kim, K. S., Kim, J. H. and Kim, W. B. (2009a), "Method for Estimating the Clamping Force of High Strength Bolts Subjected to Temperature Variation", International Journal of Steel Structures, Vol. 9, No. 2, pp. 123-130.
Nah, H. S., Lee, H. J., Kim, K. S., Kim, J. H. and Kim, W. B. (2009b), "Evaluation of Slip Coefficient of Slip Critical Joints with High Strength Bolts", Structural Engineers & Mechanics, Vol. 32, No. 4, pp. 477-488.
Nah, H. S., Lee, H. J., Choi, S. M. and Kim, W. B.(2015), "Analysis on Variation of Torque Co-efficient by Ambient Temperature of High Strength Bolt", Proc. 5th KOSACS Conference, Jeju, Korea, pp.95-96 (in Korean).
RCSC Committee(2004), Specification for Structural Joints Using ASTM A325 or A490 Bolts, AISC Inc., Chicago, Illinois, USA.
Tambori, Akbar R.(1999), Handbook of structural steel connection design and detail Design, MaGraw-Hill, USA.
Vand, E. Hemmati, Oskouei R.H., Chakherlou T.N., (2008) "Experimental Method for Measuring Clamping Force in Bolted Connections and Effect of Bolt Threads Lubrication on its Value", World Academy of Science, Engineering and Technology 22, pp. 457-460.
*원문 PDF 파일 및 링크정보가 존재하지 않을 경우 KISTI DDS 시스템에서 제공하는 원문복사서비스를 사용할 수 있습니다.
출판사/학술단체 등이 한시적으로 특별한 프로모션 또는 일정기간 경과 후 접근을 허용하여, 출판사/학술단체 등의 사이트에서 이용 가능한 논문
※ AI-Helper는 부적절한 답변을 할 수 있습니다.