최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기電磁波技術 : 韓國電磁波學會誌 = The Proceedings of the Korean Institute of Electromagnetic Engineering and Science, v.27 no.3, 2016년, pp.28 - 36
홍영표 (한국표준과학연구원) , 구현지 (한국표준과학연구원)
초록이 없습니다.
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
핵심어 | 질문 | 논문에서 추출한 답변 |
---|---|---|
평판선로의 임피던스를 결정하기 위해 필요한 것은? | 평판선로의 임피던스를 결정하기 위해서는 인쇄회로기판 (PCB; Printed Circuit Board) 또는 반도체 기판의 주파수 종속 물질상수(특히 복소유전율)에 대한 정보가 필요하다. 기판상의 전송선로의 손실을 정확히 측정 및 평가하는 연구가 진행되어 왔다[7],[8]. | |
임피던스 측정표준 확립이 중요한 이유는? | [그림 1]과 같이 전자파 임피던스는 SI 기본단위인 길이 측정표준을 사용하여 확립된다. 전자파 임피던스 및 전력 표준은 전자파분야 측정표준 체계를 구현하는 기본량이다. 또, 전자파 임피던스는 전자파 전력 표준 확립에도 사용되므로, 임피던스 측정표준 확립은 매우 기본적이며 중요하다. | |
PCB 상의 차동 전송선로는 어느 분야에서 사용될 수 있도록 연구되었는가? | 일반적으로, PCB 상의 차동 전송선로는 노이즈 내성 및 전압이득에 효과적인 장점으로 인해, 고속 인터페이스에서 주로 사용하는 신호전달기법이다. 차동 구조를 이용한 광대역 안테나[11], 평판 구조 전력합성기[12], 도파관 전력합성기[13], 푸시-풀 구조의 전력증폭기[14] 등 다양한 고주파 소자들이 연구되었다. 집적도가 높은 PCB 회로 및 반도체 기반의 IC 설계에서는 칩의 면적을 줄이기 위해 불가피하게 다층구조를 활용하며, 일반적으로 비아를 통해 연결한다. |
N. M. Ridler, R. G. Clarke, M. J. Salter, and A. Wilson, "Traceability to national standards for S-parameter measurements in waveguide at frequencies from 220 GHz to 330 GHz", Proc. 78th ARFTG Microwave Measurement Conf., pp. 1-6, Dec. 2011.
M. Horibe, R. Kishikawa, "Metrological traceability in waveguide S-parameter measurements at 1.0 THz band", IEEE Trans. Instrum. Meas., vol. 62, no. 6, pp. 1814-1820, Jun. 2013.
M. Horibe, N. M. Ridler, "Traceability via precision dimensional measurements of WM-864 (WR-03) waveguide standard shims including comparison between NPL and NMIJ", Proc. 79th ARFTG Microw. Meas. Conf. Dig., pp. 1-8, 2012.
"Test methods to determine the amount of signal loss on printed boards (PBs)", IPC-TM-650 Test Methods Manual Method 2.5.5.12, May 2009 (available for download from http://www.ipc.org/4.0_Knowledge/4.1_Standards/test/2-5_2- 5-5-12.pdf)
http://projects.npl.co.uk/hf-circuits/
M. Salter, N. Ridler, Y.- P. Hong, D. Allal, F. Ziade, M, Hudlicka, and T. Pavicek, "A reference printed circuit board (PCB) for validating microwave measurements on PCBs and a differential calibration kit for traceable measurements", EUMW Workshops and Short Courses, 2015.
Y.-P. Hong, "Fat dipole antenna with broadband balun using CPW-to-slotline field transformation", Electronics Letters, vol. 49, no. 10, pp. 635-636, May 2013.
Y.-P. Hong, Y.-J. An, and J.-G. Yook, "Differential radial power combiner using substrate integrated waveguide", Electronics Letters, vol. 46, no. 24, pp. 1607-1608, Nov. 2010.
Y.-P. Hong, D. F. Kimball, P. M. Asbeck, J.-G. Yook, and L. E. Larson, "Single-ended and differential radial power combiners implemented with a compact broadband probe", IEEE Transactions on Microwave Theory and Techniques, vol. 58, no. 6, pp. 1565- 1572, Jun. 2010.
J. J. Yan, Y.-P. Hong, K. Mukai, S. Shinjo, and P. M. Asbeck, "Broadband high PAE GaN push-pull power amplifier for 500 MHz to 2.5 GHz operation", IEEE MTT-S International Microwave Symposium, Jun. 2013.
W. R. Eisenstant, B. Stengel, and B. M. Thompson, Microwave Differential Circuit Design Using Mixed-Mode SParameters, Artech House, 2006.
R. B. Marks, "A multiline method of network analyzer calibration", IEEE Trans. Microwave Theory Tech., 39, pp. 1205-1215, Jul. 1991.
M. Wojnowski, V. Issakov, G. Sommer, and R. Weigel, "Multimode TRL calibration technique for characterization of differential devices", IEEE Trans. Microw. Theory Techn., vol. 60, no. 7, pp. 2220-2247, 2012.
A. G. Morgan, "A primary national standard impedance measurement system for the millimetre-wave frequency range", MSc dissertation, University of Surrey, Aug. 2007.
G. F. Engen, C. A. Hoer, "Thru-reflect-line: An improved technique for calibrating the dual six-port automatic network analyzer", IEEE Transactions on Microwave Theory and Techniques, vol. 27, no. 12, pp. 987-993, Dec. 1979.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.