최소 단어 이상 선택하여야 합니다.
최대 10 단어까지만 선택 가능합니다.
다음과 같은 기능을 한번의 로그인으로 사용 할 수 있습니다.
NTIS 바로가기한국기계가공학회지 = Journal of the Korean Society of Manufacturing Process Engineers, v.18 no.2, 2019년, pp.73 - 81
정석민 (금오공과대학교 기계공학과) , 김동주 (금오공과대학교 기계공학과)
Numerical simulations are performed for the thermal fluid flow around a circular cylinder, and the particle trajectories are calculated to investigate the particle motions and deposition characteristics. We aim to understand the effects of three important parameters (particle Stokes number, temperat...
* AI 자동 식별 결과로 적합하지 않은 문장이 있을 수 있으니, 이용에 유의하시기 바랍니다.
핵심어 | 질문 | 논문에서 추출한 답변 |
---|---|---|
열교환기에서는 입자의 부착을 최소화 시켜야 하는 이유는? | 필터에서는 입자를 최대한 걸러내는 것이 목표이므로 입자가 필터 표면에 잘 부착되도록 설계해야 한다. 반면 열교환기에서는 입자가 열교환기 표면에 부착되면 부식을 일으키거나 열전달율을 감소시키므로 입자의 부착을 최소화시키는 설계가 필요하다. | |
본 실험의 유동해석 방법에서 경계조건은? | 1은 실린더 주위의 유동을 해석하기 위한 해석 영역 및 경계조건을 보여준다 좌표계의 중심은 실린더의 중심으로 정의하였고 해석 영역은 x 방향으로 -20D ∼ 22D, y 방향으로 -50D ∼ 50D를 사용하였다. 경계조건으로 입구 및 원거리에서 Dirichlet 경계조건을 사용하였고, 출구에서는 Neumann 조건, 실린더 표면에서는 점착조건(No-slip condition)을 사용하였다. 자유유동의 온도는 1500K으로 고정하였고 이 온도에서의 유체 물성을 해석에 사용하였다. | |
입자의 인터셉션에 관한 모델링 3가지를 구분하시오 | 입자의 인터셉션에 관한 모델링은 크게 세 가지로 구분할 수 있다. 첫 번째는 입자를 점으로 가정하고 입자의 크기 및 인터셉션을 고려하지 않는 방법(point particle model)인데, 가장 많이 사용되는 방법이다. 두 번째는 입자의 크기를 근사적으로 고려한 모델(approximate model)로 필터의 효율 계산을 위해 제안된 방법이다. 여기서는 입자의 부착효율을 계산할때 입자를 점으로 가정하고 구한 부착효율 (ηpoint)에 실린더와 입자의 직경비를 더하여 보정한다( ). 마지막으로 입자와 실린더의 접촉 여부를 판단할 때 입자의 직경을 정확히 고려하는 방법(precise contact determination)이다. 즉, 입자 중심과 실린더 중심 사이의 거리(L)가 입자 반경(rp)과 실린더 반경(R)의 합보다 작거나 같으면, 입자와 실린더가 접촉한 것으로 판단한다(L ≤ R+rp). |
Haugen, N. E. L. and Kragset, S., "Particle impaction on a cylinder in a crossflow as function of Stokes and Reynolds numbers," J. Fluid Mech., Vol. 661, pp. 239-261, 2010.
Yao, J., Zhao, Y., Hu, G., Fan, J. and Cen, K., "Numerical simulation of particle dispersion in the wake of a circular cylinder," Aerosol Sci. Tech., Vol. 43, pp. 174-187, 2009.
Schiller, L. and Naumann, Z., "A drag coefficient correlation," Z. Ver. Deutscher Ing., Vol. 77, pp. 318-320, 1935.
Ounis, H., Ahmadi, G. and McLaughlin, J. B., "Brownian diffusion of submicrometer particles in the viscous sublayer," J. Colloid and Interface Sci., Vol. 143, pp. 266-277, 1991.
Zheng, X. and Silber-Li, Z., "The influence of Saffman lift force on nanoparticle concentration distribution near a wall," Applied Physics Letters, Vol. 95, pp. 124105-1-3, 2009.
Talbot, L., Cheng, R. K., Schefer, R. W. and Willis, D. R., “Thermophoresis of particles in a heated boundary layer,” J. Fluid Mech., Vol. 101, No. 4, pp. 737-758, 1980.
Park, J., Kwon, K. and Choi, H., “Numerical solutions of flow past a circular cylinder at Reynolds numbers up to 160,” KSME Int. J., Vol. 12, No. 6, pp. 1200-1205, 1998.
Williamson, C. H. K., "Oblique and parallel modes of vortex shedding in the wake of a circular cylinder at low Reynolds numbers," J. Fluid Mech., Vol. 206, pp. 579-627, 1989.
Mahir, N. and Altac, Z., "Numerical investigation of convective heat transfer in unsteady flow past two cylinders in tandem arrangements," Int. J. Heat and Fluid Flow, Vol. 29, pp. 1309-1318, 2008.
Knudsen, J. D. and Katz, D. L., Fluid Dynamics and Heat Transfer, McGraw Hill, 1958.
Churchill, S. W. and Bernstein, M. J., "A correlating equation for forced convection from gases and liquids to a circular cylinder in crossflow," J. Heat Transfer, Vol. 99, pp. 300-306, 1977.
Muhr, W., "Theoretical and experimental investigation of particle deposition in fibrous filters by field and inertial forces," Ph.D. Thesis, Universitat Karlsruhe, Germany, 1976.
Israel, R. and Rosner, D. E., "Use of a generalized Stokes number to determine the aerodynamic capture efficiency of non-Stokesian particles from a compressible gas flow," Aerosol Sci. and Tech., Vol. 2, pp. 45-51, 1982.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.