장골 검출기를 이용한 장골 검사에서 3D 프린터로 제작한 구리 필터의 유용성 연구 A Study on the Usefulness of Copper Filters Made with 3D Printers in Longbone Examination Using Long Length Detector원문보기
Long-bone examination is mainly used for inspection of the lower extremities. Recently, a long length detector (FXRD-1751S, VIEWORKS, Korea) with three digital detectors attached has been developed. High energy X-rays are used because pelvic areas require high image quality. In this case, X-rays are...
Long-bone examination is mainly used for inspection of the lower extremities. Recently, a long length detector (FXRD-1751S, VIEWORKS, Korea) with three digital detectors attached has been developed. High energy X-rays are used because pelvic areas require high image quality. In this case, X-rays are transmitted a lot in thin areas such as an ankle, and it is not suitable for diagnosing an image. Therefore, this study use copper filters made with 3D printers to increase image quality in the Long-bone inspection. A copper filter was manufactured in consideration of the overall thickness of the lower part. The experiment was conducted in anterior-posterior (AP) and lateral (LAT) positions, depending on the presence or absence of the filter. 5x5 pixels of region of interest (ROI) were selected from the pelvis, knee, and ankle areas. X-rays were irradiated under the conditions of 70 kVp and 40 mAs for AP, 80 kVp, and 63 mAs for lat when without filters, 90 kVp and 80 mAs for AP, 90 kVp and 100 mAs for lat when with filters. signal to noise ratio(SNR) ratio and contrast to noise (CNR) values were measured 1106.38, 14.34 before applying the filter and 1189.32, 70.43 after the filter. For the knee area, 650.44, 97.61 before applying the filter, and 1013.17, 444.24 after applying the filter. For the ankle area, 206.65, 23.68 before applying the filter and 993.50, 136.11 after applying the filter. In the Long-bone examination, SNR and CNR were greatly measured when the filter was applied, confirmed the availability of using the copper additional filter.
Long-bone examination is mainly used for inspection of the lower extremities. Recently, a long length detector (FXRD-1751S, VIEWORKS, Korea) with three digital detectors attached has been developed. High energy X-rays are used because pelvic areas require high image quality. In this case, X-rays are transmitted a lot in thin areas such as an ankle, and it is not suitable for diagnosing an image. Therefore, this study use copper filters made with 3D printers to increase image quality in the Long-bone inspection. A copper filter was manufactured in consideration of the overall thickness of the lower part. The experiment was conducted in anterior-posterior (AP) and lateral (LAT) positions, depending on the presence or absence of the filter. 5x5 pixels of region of interest (ROI) were selected from the pelvis, knee, and ankle areas. X-rays were irradiated under the conditions of 70 kVp and 40 mAs for AP, 80 kVp, and 63 mAs for lat when without filters, 90 kVp and 80 mAs for AP, 90 kVp and 100 mAs for lat when with filters. signal to noise ratio(SNR) ratio and contrast to noise (CNR) values were measured 1106.38, 14.34 before applying the filter and 1189.32, 70.43 after the filter. For the knee area, 650.44, 97.61 before applying the filter, and 1013.17, 444.24 after applying the filter. For the ankle area, 206.65, 23.68 before applying the filter and 993.50, 136.11 after applying the filter. In the Long-bone examination, SNR and CNR were greatly measured when the filter was applied, confirmed the availability of using the copper additional filter.
Kim KS, Kim SC. Comparison of Image Quality and Effective Dose by Additional Filtration on Digital Chest Tomosynthesis. Journal of Radiological Science and Technology. 2015;38(4):347-53.
Shin KR, Kim JS. A Study on Health Concern, Self-rated Health, Health Status, and Health Promotion Behavior of Elderly Women in Urban Area. Journal of Korean Academy of Nursing. 2004;34(5):869.
Kim SH. A Convergence Study on Evaluation of Usefulness of Copper Additional Filter in the Digital Radiography System. Journal of Digital Convergence. 2015;13(9):351-9.
Cho BP, Yang YC, Choi BY, Song DY, Park JC. Human Anatomy. Komoonsa. 2019;108.
Lee HS, Lim CS. Consideration of the iliac measurement imaging method-The iliac measurement imaging method using a remote control X-ray device. Journal of the Korean Radiological Technologist Association. 1998;24(2):91-4.
Jang SH, Heo JE. Effectiveness Evaluation of Scanogram Using Long-bone Detector. Journal of Radiological Science and Technology. 2020;43(4):235-42.
Jung PH, Jang DH, Kim KH, Kwon YH. A Study on Lower Extremity Scanogram Comparison according to the Examination Method. Journal of the Korean Society of Radiology. 2016;13-9.
Kang MT, Kim HS, Kang SB, Choi IH, Kang SS, Park HH, et al. Patient dose due to use added filter during radiation examination. Journal of the Korean Society of Radiology. 2015;65-169.
Kim KM, Jang SW, Woo BC, Park CH. The Usefulness analysis of using additional filter in Pediatric chest X-ray. Journal of the Korean Society of Radiology. 2017;189-94.
Shin SI, Kim CY, Kim SC. The Study on the Reduction of Patient Surface Dose Thorough the use of Copper Filter in a Digital Chest Radiography. Journal of Radiation Technology Science. 2008;31(3):223-8.
Kim SH, Kim YM, Kwon KT, Ma SC, Han DK. A Analysis of Effectiveness of Aluminium Filter in the added Compound Filtration by Detective Quantum Efficiency and Image Quality Evaluation. Journal of the Korea Contents Association. 2015;15(10):362-73.
Choi IH, Kim KT, Heo YJ, Park HH, Kang SS, Noh SC, et al. The Study of Affecting Image Quality according to forward Scattering Dose used Additional Filter in Diagnostic Imaging System. Journal of the Korean Society of Radiology. 2016;10(8):597-602.
Jang HM, Yoon J. Usefulness Evaluation and Fabrication of the Radiation Shield Using 3D Printing Technology. Journal of the Korean Society of Radiology. 2019;13(7):1015-24.
Yoon J, Yoon MS. A Study on the Effect of FFF 3D Printer Nozzle Size and Layer Height on Radiation Shield Fabrication. Journal of the Korean Society of Radiology. 2020;14(7):891-8.
Yoon MS, Kang SH, Hong SM, Lee YJ, Han DK. A Study on the Fabrication and Comparison of the Phantom for CT Dose Measurements Using 3D Printer. Journal of the Korean Society of Radiology. 2018;12(6):737-43.
Kim YC, Song JN, Choi NG, Jeong Y, Han JB. Radiation Dose and Image Evaluation for Position Change in Low Extremity Teleography. Journal of the Korean Society of Radiology. 2014;8(7):409-15.
Jang SW, Jang SW, Woo BC, Chung JY, Park CH. The Usefulness analysis of Using Additional filter in Dual energy chest X-ray. Journal of the Korean Society of Radiology. 2015;1-11.
Choi NG, Seong HJ, Jeon JS, Kim YH, Seong DO. A Comparative Study of Image Quality and Radiation Dose according to Variable Added Filter and Radiation Exposure in Diagnostic X-Ray Radiography. Journal of Radiation Protection and Research. 2012;37(1):25-34.
Kwon KT, Yoon D, Shin RU, Han BJ, Yoon MS. A Study on the Usefulness of Copper Filter in Single X-ray Whole Spine Lateral using 3D Printer. Journal of the Korean Society of Radiology. 2020;14(7):899-906.
AI-Helper
※ AI-Helper는 부적절한 답변을 할 수 있습니다.