ABDULLAH, SHAHRUM
(Department of Mechanical and Materials Engineering, Engineering Faculty, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia)
,
ARIFFIN, AHMAD KAMAL
(Department of Mechanical and Materials Engineering, Engineering Faculty, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia)
,
NIZWAN, CHE KU EDDY
(Department of Mechanical and Materials Engineering, Engineering Faculty, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia)
,
ABDULLAH, MOHAMAD FAIZAL
(Department of Mechanical Engineering, Engineering Faculty, Universiti Pertahanan National Malaysia, Kem Sungai Besi, 57000 Kuala Lumpur, Malaysia)
,
JALAR, AZMAN
(Advanced Semiconductor Packaging (ASPAC), Institute of Microengineering and Nanoelectronics (IMEN), Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia)
,
MOD YUNOH, MOHD FARIDZ
(Advanced Semiconductor Packaging (ASPAC), Institute of Microengineering and Nanoelectronics (IMEN), Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia)
This paper presents a durability analysis of two types of copper leadframe, i.e. the un-oxidised leadframe and the oxidised leadframe. Both leadframe types were used in the fabrication process of a Quad Flat No-Lead (QFN) package, which can be said as a recent type of the 3D stacked die semiconducto...
This paper presents a durability analysis of two types of copper leadframe, i.e. the un-oxidised leadframe and the oxidised leadframe. Both leadframe types were used in the fabrication process of a Quad Flat No-Lead (QFN) package, which can be said as a recent type of the 3D stacked die semiconductor package. This study involved the durability test and analysis on QFN packages when these packages were subjected under constant cyclic loadings. In order to perform the cyclic test, the procedure of the three-point cyclic bending test has been employed on the packages. In addition, a strain gauge which was connected to the dynamic data acquisition system was used for each tested QFN package for determining the response of the captured cyclic strain signal. It has been found that the variable amplitude pattern of signal response has been obtained during the constant cyclic test. The obtained response signals for both type of leadframe were then analysed using the approaches of signal processing technique, which is relatively new in this field. The collected response signal were analysed using the normal statistical methods, the Power Spectrum Density (PSD) calculation and also the time-frequency localization analysis. From the detail signal analysis, it has been found that the un-oxidised leadframe showed a lower range of strain response compared to the oxidised leadframe, indicating higher lifetime. As a result, this finding lead to the durability conclusion, for which the un-oxidised leadframe has more durability effects and it also has higher lifetime compared to the oxidised leadframe. Finally, a micro-crack phenomenon at the epoxy interface between the die and the leadframe was also observed for the QFN package with the oxidised leadframe.
This paper presents a durability analysis of two types of copper leadframe, i.e. the un-oxidised leadframe and the oxidised leadframe. Both leadframe types were used in the fabrication process of a Quad Flat No-Lead (QFN) package, which can be said as a recent type of the 3D stacked die semiconductor package. This study involved the durability test and analysis on QFN packages when these packages were subjected under constant cyclic loadings. In order to perform the cyclic test, the procedure of the three-point cyclic bending test has been employed on the packages. In addition, a strain gauge which was connected to the dynamic data acquisition system was used for each tested QFN package for determining the response of the captured cyclic strain signal. It has been found that the variable amplitude pattern of signal response has been obtained during the constant cyclic test. The obtained response signals for both type of leadframe were then analysed using the approaches of signal processing technique, which is relatively new in this field. The collected response signal were analysed using the normal statistical methods, the Power Spectrum Density (PSD) calculation and also the time-frequency localization analysis. From the detail signal analysis, it has been found that the un-oxidised leadframe showed a lower range of strain response compared to the oxidised leadframe, indicating higher lifetime. As a result, this finding lead to the durability conclusion, for which the un-oxidised leadframe has more durability effects and it also has higher lifetime compared to the oxidised leadframe. Finally, a micro-crack phenomenon at the epoxy interface between the die and the leadframe was also observed for the QFN package with the oxidised leadframe.
참고문헌 (11)
Lanford, W.A., Ding, P.J., Wang, Wei, Hymes, S., Murarka, S.P..
Alloying of copper for use in microelectronic metallization.
Materials chemistry and physics,
vol.41,
no.3,
192-198.
Signal Processing Algorithms in Fortran and C Stearns S. D. 1993
The Scientist and Engineer's Guide to Digital Signal Processing Smith S. W. 1999
Cooley, James W., Tukey, John W..
An algorithm for the machine calculation of complex Fourier series.
Mathematics of computation,
vol.19,
no.90,
297-301.
Kıymık, M.Kemal, Güler, İnan, Dizibüyük, Alper, Akın, Mehmet.
Comparison of STFT and wavelet transform methods in determining epileptic seizure activity in EEG signals for real-time application.
Computers in biology and medicine,
vol.35,
no.7,
603-616.
Hirohata, K., Kawamura, N., Mukai, M., Kawakami, T., Aoki, H., Takahashi, K..
Mechanical fatigue test method for chip/underfill delamination in flip-chip packages.
IEEE transactions on electronics packaging manufacturing : a publication of the IEEE Components, Packaging, and Manufacturing Technology Society,
vol.25,
no.3,
217-222.
Manson, S. S..
Fatigue: A complex subject-Some simple approximations : Both ends of the fatigue spectrum are covered in this lecture. On the one hand, the present state of understanding of the mechanism is reviewed and the complexity of the process observed. On the other hand, some approximations useful in design are outlined and their application illustrated.
Experimental mechanics,
vol.5,
no.4,
193-226.
AI-Helper
※ AI-Helper는 부적절한 답변을 할 수 있습니다.