휘발성유기화합물의 작업용 표준시료의 분석과 오차의 발생에 대한 특성 - 희석과정이 분석결과에 미치는 영향 The Analysis of vac Working Standards and their Analytical Bias : the Effect of Dilution on Measurement Data Sets
이 연구에서는 표준시료의 보관에 필요한 테들러백을 사용하여, 작업용 표준시료를 희석조제하였다. 그리고 표준시료의 조제 또는 분석과 연계된 오차를 희석조제의 배수와 연계하여 설명하고자 하였다. 이러한 비교를 위해, 초기농도가 다른 4 개의 표준 시료 (10, 20, 50, 100 ppb)를 준비하였다. 이들 각각의 시료를 농도의 크기에 관계없이 모두 동일한 검량조건 (유속과 시간)으로 시료를 공급하면서 열탈착을 유도하여, 각 농도대별 검량곡선을 도출하였다. 그 결과, 가장 저농도 (10 ppb) 표준가스에서 대부분 성분들 (benzene, toluene, p-xylene)의 회수율이 가장 떨어지는 것으로 나타났다. 또한 상대적으로 고분자 화합물인 스티렌의 경우, 분석의 오차가 더 크게 나타났다. 추가적으로 표준시료의 성상차이에 따른 검량특성을 비교하기 위해, 기체상 표준시료와 액상 표준시료에 대한 검량특성을 유사한 함량 기준에서 평가하고자 하였다. 성상이 다른 두 개의 표준시료로 동일한 농도대에서 검량하였을 때, 튜브방식으로 준비한 액상표준시료의 검량결과에 대비하여 기체상 표준시료의 회수율은 benzene 56%, toluene 42%, p-xylene 31%, styrene 25% 수준으로 나타났다. 이 연구의 결과, 모든 표준시료나 미지시료의 분석을 가급적 동일한 매질조건 또는 유량조건에서 실시하는 것이 이상적이란 점을 확인 할 수 있었다.
이 연구에서는 표준시료의 보관에 필요한 테들러백을 사용하여, 작업용 표준시료를 희석조제하였다. 그리고 표준시료의 조제 또는 분석과 연계된 오차를 희석조제의 배수와 연계하여 설명하고자 하였다. 이러한 비교를 위해, 초기농도가 다른 4 개의 표준 시료 (10, 20, 50, 100 ppb)를 준비하였다. 이들 각각의 시료를 농도의 크기에 관계없이 모두 동일한 검량조건 (유속과 시간)으로 시료를 공급하면서 열탈착을 유도하여, 각 농도대별 검량곡선을 도출하였다. 그 결과, 가장 저농도 (10 ppb) 표준가스에서 대부분 성분들 (benzene, toluene, p-xylene)의 회수율이 가장 떨어지는 것으로 나타났다. 또한 상대적으로 고분자 화합물인 스티렌의 경우, 분석의 오차가 더 크게 나타났다. 추가적으로 표준시료의 성상차이에 따른 검량특성을 비교하기 위해, 기체상 표준시료와 액상 표준시료에 대한 검량특성을 유사한 함량 기준에서 평가하고자 하였다. 성상이 다른 두 개의 표준시료로 동일한 농도대에서 검량하였을 때, 튜브방식으로 준비한 액상표준시료의 검량결과에 대비하여 기체상 표준시료의 회수율은 benzene 56%, toluene 42%, p-xylene 31%, styrene 25% 수준으로 나타났다. 이 연구의 결과, 모든 표준시료나 미지시료의 분석을 가급적 동일한 매질조건 또는 유량조건에서 실시하는 것이 이상적이란 점을 확인 할 수 있었다.
In this study, an attempt was made to measure uncertainties involved in the analysis of gaseous VOC standards prepared at various dilution stage. A GC/FlD system equipped with air server/thermal desorption (AS/TD) unit was used to draw calibration curves for the known amounts of VOC gases (including...
In this study, an attempt was made to measure uncertainties involved in the analysis of gaseous VOC standards prepared at various dilution stage. A GC/FlD system equipped with air server/thermal desorption (AS/TD) unit was used to draw calibration curves for the known amounts of VOC gases (including benzene, toluene, xylene, and styrene) prepared at four individual concentrations (10, 20, 50, and 100 ppb). The calibration curves obtained from standards of each respective concentration were compared with each other. It was found that the loss of samples was more prominent with decreasing standard concentrations (e.g., one prepared at 10 ppb) and that the heaviest compound, styrene exhibited the most noticeable loss than the others. In this study, an ancillary experiment was also conducted to evaluate the compatibility of standards between gaseous (using Tedlar bag) and liquid phases (using tube method). Based on this comparative analysis, the compatibility between two standard type was evaluated in terms of the recovery ratio between gas and liquid: 56 (benzene), 42 (toluene), 31 (p-xylene), and 25% (styrene).
In this study, an attempt was made to measure uncertainties involved in the analysis of gaseous VOC standards prepared at various dilution stage. A GC/FlD system equipped with air server/thermal desorption (AS/TD) unit was used to draw calibration curves for the known amounts of VOC gases (including benzene, toluene, xylene, and styrene) prepared at four individual concentrations (10, 20, 50, and 100 ppb). The calibration curves obtained from standards of each respective concentration were compared with each other. It was found that the loss of samples was more prominent with decreasing standard concentrations (e.g., one prepared at 10 ppb) and that the heaviest compound, styrene exhibited the most noticeable loss than the others. In this study, an ancillary experiment was also conducted to evaluate the compatibility of standards between gaseous (using Tedlar bag) and liquid phases (using tube method). Based on this comparative analysis, the compatibility between two standard type was evaluated in terms of the recovery ratio between gas and liquid: 56 (benzene), 42 (toluene), 31 (p-xylene), and 25% (styrene).
※ AI-Helper는 부적절한 답변을 할 수 있습니다.