[논문]A Double-Sided In-Plane Lateral Comb-Drive Actuator Fabricated by a Plaster-Based 3D-Printer

Mizuno, Jun; Takahashi, Satoshi

doi:10.4028/www.scientific.net/kem.656-657.594

[해외논문] A Double-Sided In-Plane Lateral Comb-Drive Actuator Fabricated by a Plaster-Based 3D-Printer

Key engineering materials, v.656/657, 2015년, pp.594 - 599

Mizuno, Jun (Ishinomaki Senshu University) , Takahashi, Satoshi (Ishinomaki Senshu University)

Abstract ▼ AI-Helper

In this paper, design, fabrication and characterization of a double-sided in-plane lateral comb-drive actuator fabricated by a plaster-based 3D-printer is described. The design is based on MEMS (Micro Electro-mechanical Systems) design concept. The movable part of the actuator consists of a (10x52.5) mm rectangular plate, and the end sides have depression areas in order to fit a (0.5x21.3) mm beam-shaped hinges. In the remaining sides of the plate, 18 comb fingers (0.5x10) mm are set at each opposite side. The stationary part of the actuator consists of 17 comb fingers with the same dimension to that of the stationary ones, and they are set at both sides of a frame and interdigitated with the movable comb fingers on the same plane. The gap between the movable and stationary comb fingers is 1.0mm. The structure thickness is 1.5mm. Such a structure, which both sides are provided with an in-plane interdigitated comb fingers, is called double-sided in-plane lateral comb-drive actuator. This actuator has been fabricated by using a plaster-based 3D-printer. Since plaster composite is an electrical insulating material, the structure has been suitably masked and the upper and lateral surfaces have been metallized thereafter by Au ion sputtering for the actuator electrodes formation. The hybrid fusion of 3D-printing manufacturing technology and MEMS-based design concept has been recently proposed by the authors and named as SMEMS (Sub-milli Electro-mechanical Systems), since the smallest possible fabrication size is in the order of sub-millimeters. The advantage of SMEMS technology is the quick and easy fabrication of 3D structures from 3D-CAD data. Furthermore, SMEMS is completely environment-clean since any hazardous chemicals or gases are used. The actuator has been driven by differential voltages, where both sides are biased at a voltage of 100V, and a 200 Vpp and its 180°shifted sinusoidal voltages are applied at each side. The actuator laterally moved by 96.8μm (full width) at a resonance frequency of 72Hz, and the mechanical quality factor has been estimated to be about 10.

참고문헌 (18)

C. Wu, Y. Xie, S. M. Mok, Linking product design in CAD with assembly operations in CAM for virtual product assembly, Assembly Autom. 27(4) (2007) 309-323. 10.1108/01445150710827096

상세보기
10.1080/13102818.2008.10817506 G. Uzun, An overview of dental CAD/CAM systems, Biotechnol. Biotec. Eq. 22(1) (2008) 530-535.

상세보기
10.1080/21693277.2014.907533 N. Prabhu, M. D. Anand, L. E. Ruban, Structural analysis of Scorbot-ER Vu plus industrial robot manipulator, Prod. Manuf. Res. 2(1) (2014) 309-325.

상세보기
M. Wu, W. Zhao, Y. Tang, D. Li, B. Lu, A novel stereolithography technology with conventional UV light, Rapid Prototyping J. 7(5) (2001) 268-275. 10.1108/eum0000000006117

상세보기
D. Dimitrov, K. Schreve, A. Taylor, B. Vincent, Rapid prototyping driven design and realization of large components, Rapid Prototyping J. 13(2) (2007) 85-91. 10.1108/13552540710736768

상세보기
S. Stopp, T. Wolff, F. Irlinger, T. Lueth, A new method for printer calibration and contour accuracy manufacturing with 3D-print technology, Rapid Prototyping J. 14(3) (2008) 167-172. 10.1108/13552540810878030

상세보기
S. Vinodh, G. Sundararaj, S. R. Devadasan, D. Kuttalingam, D. Rajanayagam, Agility through rapid prototyping technology in a manufacturing environment using a 3D printer, Journal of Manuf. Technol. Manag. 20(7) (2009) 1023-1041. 10.1108/17410380910984267

상세보기
10.3722/cadaps.2011.357-371 K. Chang, T. Long, Rapid prototyping for large-scale and complex assemblies, Comput. Aided Des. Appl. 8(3) (2011) 357-371.

상세보기
Y. Cheng, Y. Lin, K. Shih, Rapid prototyping mandible model for dental implant surgery simulation, Comput. Aided Des. Appl. 9(2) (2012) 177-185. 10.3722/cadaps.2012.177-185

상세보기
D. A. Roberson, D. Espalin, R. B. Wicker, 3D printer selection: A decision-making evaluation and ranking model, Virtual and Phys. Prototyp. 8(3) (2013) 201-212. 10.1080/17452759.2013.830939

상세보기
C. Lowrie, M. P. Y. Desmulliez, L. Hoff, O. J. Elle, E. Fosse, Fabrication of a MEMS accelerometer to detect heart bypass surgery complication, Sensor Rev. 29(4) (2009) 319-325. 10.1108/02602280910986557

상세보기
10.7567/JJAP.51.080001 M. Esashi, Revolution of sensors in micro-electromechanical system, Jpn. J. Appl. Phys. 51 (2012) 80001-1 - 80001-8.
R. Bogue, Recent developments in MEMS sensors: a review of applications, markets and technologies, Sensor Rev., 33(4) (2013) 300-304. 10.1108/sr-05-2013-678

상세보기
A. M. Hynes, H. Ashraf, J. K. Bhardwaj, J. Hopkins, I. Johnston, J. N. Shepherd, Recent advances in silicon etching for MEMS using the ASETM Process, Sensor Actuat. A-Phys. 74 (1999) 13-17. 10.1016/s0924-4247(98)00326-4

상세보기
D. A. Lashof, D. R. Ahuja, Relative contributions of greenhouse gas emission to global warming, Nature 344 (1990) 529-531. 10.1038/344529a0

상세보기
G. T. Mulhern, D. S. Soane, R. T. Howe, Supercritical carbon dioxide drying of micro-structures, Proc. 7th Int. Conf. Solid-State Sensors, Actuators and Microsytems (Transducers '93) (1993) 296-299.
J. Mizuno, S. Takahashi, A fundamental study of sub-millimeter electro-mechanical systems (SMEMS) structures based on a 3D-printer, Proc. 2nd Int. Symp. Fund. Appl. Sci. (ISFAS 2014) (2014) 1460-1462.
10.9756/SIJCSEA/V2I4/0203210401 J. Mizuno, S. Takahashi, Characterization of an in-plane single-sided lateral comb actuator fabricated by a 3D-printer, Stand. Int. J. T. Comput. Sci. Eng. Appl. (2014) 99-104.

상세보기

활용도 분석정보

상세보기

다운로드

내보내기

활용도 Top5 논문

해당 논문의 주제분야에서 활용도가 높은 상위 5개 콘텐츠를 보여줍니다.
더보기 버튼을 클릭하시면 더 많은 관련자료를 살펴볼 수 있습니다.

내보내기 구분	파일저장 인쇄 메일전송
구성항목	기본정보 상세정보 관리번호, 논문명, 저널/프로시딩명, 저자 , 발행년, 권, 호, 시작페이지, 끝페이지, 발행기관 관리번호, 논문명, 대등논문명, 저자 , 저널/프로시딩명, 발행기관, 발행년, 발행언어, 권, 호, 시작페이지, 끝페이지, ISBN, ISSN, 주제분야, 키워드, 초록(한글), 초록(영문), 저자(소속기관)
저장형식	Text(ASCII format) Excel format RefWorks Direct Export RIS format (for Reference Manager, ProCite, EndNote), Scholar's Aids, Mendeley
메일정보	받는사람 (필수) @ 보내는사람 (선택) @ 제목 내용 KISTI 검색결과 이메일 서비스
안내	총 건의 자료가 검색되었습니다. 다운받으실 자료의 인덱스를 입력하세요. (1-10,000) 검색결과의 순서대로 최대 10,000건 까지 다운로드가 가능합니다. 데이타가 많을 경우 속도가 느려질 수 있습니다.(최대 2~3분 소요) 다운로드 파일은 UTF-8 형태로 저장됩니다. 파일의 내용이 제대로 보이지 않을실 때는 웹브라우저 상단의 보기 -> 인코딩 -> 자동선택 여부를 확인하십시오. ~ Text(ASCII format) Excel format

연합인증

[해외논문] A Double-Sided In-Plane Lateral Comb-Drive Actuator Fabricated by a Plaster-Based 3D-Printer

Abstract ▼ AI-Helper

참고문헌 (18)

이 논문을 인용한 문헌

활용도 분석정보

활용도 Top5 논문

관련 콘텐츠

원문 URL 링크

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트

연합인증

[해외논문] A Double-Sided In-Plane Lateral Comb-Drive Actuator Fabricated by a Plaster-Based 3D-Printer

Abstract ▼ AI-Helper

참고문헌 (18)

이 논문을 인용한 문헌

활용도 분석정보

활용도 Top5 논문 더보기

관련 콘텐츠

원문 URL 링크

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트

활용도 Top5 논문