I. 제 목 보급형 제로에너지 하우스 개발 II. 연구개발의 목적 및 중요성 97년 기준 국내 주택 보급호수는 총 920만호. 이중 아파트 제외한 단독, 연립 및 다세대 주택의 호수는 580만호로 연간 16400(천TOE)의 에너지를 소비하고 있다.. 이는 국가 총에너 지 소비량의 13.8%를 차지함.(건물분야 전체는 24%) 건물분야의 에너지와 관련한 기술개발은 현재까지 건물에너지 절약 기술 이라는 수동적 차원의 접근에 초점이 맞추어져 왔기 때문에 근본적인 대비책의 한계에 도달했다고 볼 수 있 으며, 따라서 곧 다가올 에너지 고갈
I. 제 목 보급형 제로에너지 하우스 개발 II. 연구개발의 목적 및 중요성 97년 기준 국내 주택 보급호수는 총 920만호. 이중 아파트 제외한 단독, 연립 및 다세대 주택의 호수는 580만호로 연간 16400(천TOE)의 에너지를 소비하고 있다.. 이는 국가 총에너 지 소비량의 13.8%를 차지함.(건물분야 전체는 24%) 건물분야의 에너지와 관련한 기술개발은 현재까지 건물에너지 절약 기술 이라는 수동적 차원의 접근에 초점이 맞추어져 왔기 때문에 근본적인 대비책의 한계에 도달했다고 볼 수 있 으며, 따라서 곧 다가올 에너지 고갈 및 환경 대란에 대비해 건물 분야에서도 절약 기술 과 대체에너지 기술 을 혼합한 기술개발에 초점을 맞추어 대비책을 수립할 필요성이 시급함. 건물 분야의 대체에너지 활용을 위한 활발한 연구가 진행되어서 실제 태양열 건물의 시 공사례도 많았으나, 90년대 들어서는 오히려 연구사업은 물론 시공 보급도 매우 미진한 상태 에 머무르고 있다. 부진의 근본적 원인은 각종 요소기술을 건축 설계과정부터 건물에 통합시 켜야 하는 태양열 건축 기술의 특성상 설계 실무진과 엔지니어링 연구진과의 연계성 부재가 주 원인이며, 또한 각종 절약기술의 기반하에 태양열 시스템과 같은 대체기술이 순차적으로 적용되어야 하는 기본적 접근방법 상의 문제 등을 들 수 있슴. 태양열 건물은 본질적 특성상 난방위주의 건물에 보다 손쉽게 실현될 수 있다. 국내 건 물부분 총에너지 소비량중 75%는 주거용 건물부분에 소비되고 있으며, 이중 78% 이상이 난 방, 급탕에 소비되어, 국가 총에너지소비의 10.6%가 아파트를 제외한 주택의 난방 및 급탕이 차지하고 있는 실정이다. 즉 주거용 건물에너지 소비의 대부분이 난방 및 급탕에 소비되고 있 음을 의미하며, 태양열 등의 대체에너지 기술을 통해 막대한 국가에너지 총 소비량을 절감할 수 있는 잠재성을 가지고 있는 것이다. 제로에너지 솔라 하우스는 주택 부하구성비에 맞는 절약 및 대체 에너지 핵심 요소기술 을 선별, 체계적인 단계별 기술적용을 통해, 화석연료나 외부 전원공급 없이 주택 자체에서 모든 에너지를 자급하는 미래 지향적 기술이다. 건물은 여러 요소기술이 모인 통합시스템이기 때문에, 절약이나 대체 등 각종 요소기술의 산발적 적용을 통해서는 에너지자립화가 불가능하 다. 따라서 적용기술의 경제성을 고려해서 에너지소비 비중이 가장 큰 주택 난방 및 급탕 분 야의 우선 자립을 우선 목표로 3년 뒤 데모건물 수준의 70% 순부하 에너지자립주택 개발, 6 년 뒤 상업화 수준의 70% 에너지자립주택을 개발하고, 최종적으로 10년뒤 100% 에너지자립 화된 제로에너지 솔라하우스를 단계적으로 개발할 필요가 있음. III. 연구개발의 내용 및 범위 본 연구에서는 다음과 같은 내용이 수행되었다. 제로에너지 솔라하우스 요소기술 통합 설계 및 평가 TI 축열벽 시스템 최적 설계 및 평가 외벽의 기밀화 및 열교 방지 기술 개발과 고단열 구조의 열유동 측정 및 분석 외벽 U=0.18 (w/ )이하 고단열 외벽 시스템 설계 및 평가 300CMH규모 환기열 회수 Test Loop 설계 및 제작, 성능평가 고효율 태양열 집열기 최적설계 및 평가, 성능평가 70% 에너지 자립을 위한 태양열/에너지 냉난방 및 온수급탕 시스템 설계 및 평가 IV. 연구개발 결과 및 활용에 대한 건의 슈퍼단열 및 고 기밀시스템, 환기회수시스템, 고효율 태양열 집열시스템 및 히트펌프시스템, 자연형 태양열시스템과 이들을 포함한 각종 요소기술 통합화 기술에 대해서 연구하였으며 또 한 이를 토대로 60평 규모의 실험용 주택을 설계 및 분석하였다. 그 결과를 요약하면 다음과 같다. 에너지자립형 건물임을 감안하여, 건물외피의 열관류율(K)을 0.15(Kcal/m2.h )이하가 되도 록 계획하였다. - 단열공법에서는 외단열 시스템이 실온변동, 열교현상 및 표면결로 등에서 내단열보다 유리한 것으로 조사되었으며 또한 열교부위를 통한 열손실의 척도가 되는 모서리 열손 실계수도 외단열이 내 중단열에 비해 작은 것으로 분석되었된 부하의 20 30%를 차지하는 바, 초단열외피시스템에서는 그 비중이 더 커지므로 철저한 보강이 필요한 것으로 판단됨. - 방습층은 단열재 내측에 설치되어야 하며, 가장 적합한 재료로는 polyethylene film으로 서 두께는 0.03 0.05 mm정도가 알맞고 겹침부분은 50 150mm를 둔다. - 침기를 막기 위한 기밀화 방안으로는 개구부의 숫자 및 크기를 줄이고, 공기/수증기 차 단막을 설치하며, 모서리부분(접합부)을 밀봉하고, 전기콘센트, 설비배관용 슬리브 등을 밀실하게 시공하여야 함. 환기 풍량 300CMH 규모의 환기열회수 시스템을 대상으로 자료조사 및 성능분석을 하였 으며 90% 이상의 효율을 갖는 열교환기를 선정하여 주택에서의 효율적인 환기를 위한 급 배기 유동경로(flow path) 와 시스템 계통도를 도출하였다. - 열유동 해석결과 유동분포나 온도분포 면에서 바닥급기 천장배기 방식이 가장 효율적 이었으나 좌식생활과 효율적인 공간활용의 관점에서 볼 때 천정급배기 방식이 바람직 함. - 실험결과 열교환 효율이 95% 정도로 나타나고 있어 직접 실내로 공급할 경우도 냉열감 을 느끼지 않으며 별도의 예열시스템이 필요 없다. 또한 기밀주에서 환기량 부족으로 인하여 오염도가 증가하는 문제점이 발생할 경우 양호한 실내공기질의 확보를 위하여 설계 환기량보다 필요 신선 환기량을 증가시킬 수 있다. - 급기구는 문에서 멀리 떨어진 곳에 위치하고 배기구는 문과 가깝도록 하는 것이 효율 적인 유동경로이다. 건축 실무진에 의해 도출된 건축설계 계획안을 대상으로 각종 요소기술에 대한 종합적 에 너지 성능평가를 수행하여, 각 설계변수의 최적화를 도모하였으며, 궁극적으로 계획된 설 계안을 통해 도출할 수 있는 에너지 자립도를 예측하였다. - 최종 제시된 설계안에 대한 각종 성능평가 결과를 요약하면 표 1과 같다. 표 1에 정리 된 바와 같이 일반주택을 모델링한 기준모델을 중심으로, 핵심 요소기술을 개별적으로 적용한 경우 난방 에너지 절감량 평가 결과와, 이들 요소기술을 조합하여 적용한 통합 적용 해석결과를 절감량 및 절감비율 형태로 예시하였다. <표 1> 제로에너지 주택의 적용기술별 난방에너지 소비량 (난방면적 : 138.6 기준) 적용기술 총난방에너지 절감량 (kWh/ ) 절감비율 (% )(kWh) (kWh/ ) 기준모델 12,379 89.3 - - 개별적 적용해 석 슈퍼단열 6,417 46.3 46.03 49% 슈퍼윈도우 10,570 76.3 13.1 15% 침기량 0.1회/ h 7,923 57.2 32.15 36% 0.3회/ h 10,235 73.9 15.5 17% 자연형 시스템 단창 매스월(약15 ) 11,392 82.2 7.1 8% 이중로이유리 매스월(약15 ) 11,114 80.2 9.1 10% 투명단열 매스월(약15 ) 10,684 77.0 12.2 13% 부착 온실 예열환기 (X) 이중유리(투명) 12,379 89.3 - - 투명단열(불투명) 12,401 89.5 -0.02 -1% 예열환기 (O ) 이중유리(투명) 11,912 86.0 3.3 4% 투명단열(불투명) 11,332 85.2 4.1 5% 통합적 적용해 석 슈퍼단열 + 침기량0.1회/ h 2,683 19.4 70.0 79% 슈퍼단열 + 침기량0.3회/ h 4,357 31.4 57.9 65% 슈퍼단열 + 침기량0.1회/ h+ 슈퍼윈도우 1,195 8.6 80.7 90% 슈퍼단열 + 침기량0.3회/ h+ 슈퍼윈도우 2,851 20.6 68.7 77% 슈퍼단열 + 침기량0.1회/ h+ 슈퍼윈도우 +TIM 969 7.0 82.3 92% 슈퍼단열 + 침기량0.3회/ h+ 슈퍼윈도우 +TIM 2,266 16.4 73.0 81.6 - 분석결과에 나타난 바와 같이 여러 요소기술 중 절감폭이 가장 큰 것은 슈퍼단열로 적 용시 기존 부하대비 약 49%의 절감효과를 기대할 수 있는 것으로 나타났다. 기존 이중 창을 모두 슈퍼윈도우로 대체할 경우는 약 15%의 절감효과를 기대할 수 있는 것으로 나타났다. - 1층 및 2층 침실에 적용한 축열벽 방식의 자연형 태양열 시스템의 성능은 구성 방식에 따라 약 8 13%의 절감효과를 기대할 수 있는 것으로 나타나감폭이 상대적으로 작게 나타났다. 이는 자연 집열면에만 적용하였기 때문으로 판단된다. 단창 매스월 대신 투명단열 시스템을 적용할 경우 추가적으로 약 5%의 성능개선 기대할 수 있는 것 으로 나타났다. - 반면 남측면 우측공간에 위치한 온실공간의 경우 약 4 5%의 에너지 절감성능을 기대 할 수 있는 것으로 나타나, 에너지 성능개선에 큰 영향을 미치지는 못하는 것으로 판명 되었다. 온실공간의 당초 계획목적이 열적인 기대효과 보다는 기존주택과의 조형적 일 치성을 위한 형상의 변화목적과 대규모 남측 집열면의 확보인 점을 고려한다면 수용할 만한 수준의 절감량을 평가된다. 특히 온실공간의 경우 배열회수 시스템과 연계하여 주 택내 신선공기 도입을 위한 예열부하용으로 활용되어야 할 것으로 판단된다. - 한편 외피의 기밀시공 및 이에 따른 강제환기 배열회수 시스템과 직접적으로 연관되는 침기량 해석결과 에너지 성능에 상대적으로 매우 큰 영향을 미치는 변수로 판명되었다. 건물 완공후 재실인원을 고려할 때 건강환기를 위한 최소 환기량은 약 0.3회/hr에 해당 하는 것으로 계산되었다. 전체 주택에 대한 침기율 변화 해석 결과 침기량 0.1회/hr당 약 17%의 에너지 소비성능 변화를 나타내었다. 침기율에 대한 해석결과는 향후 배열회 수 시스템에 대한 세부적 설계과정에서 온실을 통한 예열부하와 연계하여 종합적인 추 가 연구가 수행되어야 할 것으로 판단된다. - 각종 요소기술을 조합하여 통합성능 평가를 수행한 결과 조합방식에 따라 65 92%의 절감성능을 나타낼 수 있을 것으로 해석되었다. 현재 제시된 70% 에너지자립 제로에너 지 태양열 주택 설계안을 기준으로 슈퍼단열과 슈퍼윈도우, 1층 및 2층 남측면 공간에 투명단열 시스템, 우측 남측 공간에 비난방 온실시스템, 1층 및 2층 거실 남면에 바닥축 열 집적획득 방식이 적용된 것을 가정할 경우 기존주택 대비 약 82%의 난방에너지 자 립율을 달성 할 수 있는 것으로 나타났다. 이때 침기율을 0.3회를 가정했으며, 배열회수 시스템 및 온실공간의 예열부하를 추가적으로 고려한다면 자립율은 더 높아질 수 있을 것으로 기대된다. 단 여기서 제시된 부하값은 설비기기의 효율 및 분배손실을 고려하지 않은 순수부하이기 때문에 실제 건립시 이들 손실요인에 대한 추가적 평가가 진행되어 야 할 것이다. 고효율 집열기 개발을 위해 집열기 내에서 발생하는 자연대류 열전달을 억제함으로서 집 열기의 효율을 향상시키고자 하였으며, 이를 위하여 기존의 평판형 집열기에 투명단열재 를 내장한 모델에 대하여 이론해석 및 실험을 수행하였다. 투명단열재로는 아세테이트 셀 룰로우스(CA)로 만든 9mm x 9mm인 사각셀(square cell) 타입과 폴리카아보네이트(PC)로 만든 3.5mm의 모세관(capillary) 타입을 사용했다. - 기존의 평판형 집열기에 투명단열재를 내장함에 따라 다소간의 투과율 감소가 나타나 나, 집열기내의 자연대류에 따른 열전달 효과를 현저하게 감소시키게 된다. 열손실량의 감소는 사각셀 타입 TI-집열기의 경우에 약 29 %, 모세관 타입 TI-집열기의 경우는 약 25 % 정도인 것으로 각각 나타났다. - 본 연구의 결과 사각셀(9mm 9mm) 타입 TI-집열기의 집열효율이 모세관(직경 3.5mm) 타입 TI-집열기보다 다소 높게 나타났는데, 이는 셀 공간이 작은 모세관 타입 TI-집열기가 자연대류 감소의 영향보다는 투과율 감소의 영향으로 인해 상대적으로 사 각셀 타입 TI-집열기의 집열효율이 증가한 것으로 판단되었다. - TI-집열기를 45 각도로 14장을 설치할 경우에 TI-집열기의 성능곡선 실험식을 사용하 여 간이 계산한 결과, TI-집열기의 년간 태양열 집열량은 기존의 평판형 집열기에 비해 대략 20 % 정도 더 증가하는 것으로 나타났다. 보급형 에너지 자립하우스의 냉난방 및 온수급탕시스템을 위해서 적용가능한 시스템에 대 해서 검토하고 설계하였다. 그 결과 태양열시스템과 적정한 열원만 확보되면 에너지효율 측면에서 일반적인 보일러보다 우수하고 하절기에 냉방까지도 가능한 히트펌프시스템이 고려되었다. 히트펌프는 태양열원식과 지중열원식으로 시뮬레이션과 기초시험장치를 통해 분석하였다. - 태양열시스템은 태양의존율이 높고 저온난방이 가능하도록 설계되었다. 설계된 시스템 의 연평균 태양의존율은 컴퓨터 시뮬레이션 결과 약 81%로 나타났다. - 태양열시스템의 분석은 시스템 성능 및 경제성에 중요한 영향을 미치는 집열면적, 축열 조 용적이 태양열 의존율에 미치는 영향을 분석하였다. 이 자료는 차후 시스템의 경제 성분석에 중요한 자료로 이용될 것으로 사료된다. - 히트펌프 단독으로 냉난방 및 온수급탕이 가능하도록 시스템을 설계하였다. - 난방 및 온수급탕의 보조열원으로 이용될 수 있으면서 하절기 냉방용으로 사용될 수 있는 지중열 및 태양열 열원식 히트펌프시스템은 시뮬레이션과 기초시험장치를 통해서 그 성능을 분석하였다. 분석은 열원의 온도에 따른 히트펌프의 COP, 출력, 전력소모량 등을 분석하였다.
Abstract▼
I.Title Development of Zero energy solar house (ZeSH) II.Objectives and Significance 13.8% of total energy consumption in Korea is used in residential house. Both the energy conservation and alternative energy technology must be together applied for the energy sufficient or low energy building. But
I.Title Development of Zero energy solar house (ZeSH) II.Objectives and Significance 13.8% of total energy consumption in Korea is used in residential house. Both the energy conservation and alternative energy technology must be together applied for the energy sufficient or low energy building. But by now R & D in this field was conducted separately. 78% of the energy consumption in a residential house is for the space and water heating energy. So large quantity of energy saving by solar thermal energy is possible Zero energy solar house is a important technology in the near future. It cannot be reach with an application separately of unit technology because building is integrated system of several energy conservation technologies. So related energy technologies including solar energy must be developed and adapted gradually considering the installation cost. The objective of this study is to develop the 70% net energy self- sufficient demonstration house in 3 years, the commercialization in 6 years and 100% in 10 years. III.Contents and Scope ofProject Integration Design and Evaluation of unit Technology for the ZeSH Design and Evaluation of Transparent Insulation(TI) Storage Wall Development and analysis of Super- insulation and air- tightness Super- insulation and air- tightness Optimal design and estimation of solar collector for high efficiency Manufacturing and performance estimation for unit module of solar collector of 2m2 Design and analysis of Heat Recovery ventilation system of 300CMH capacity Design and evaluation of active solar heating with solar assist and ground source heat pump IV.Resultand Recommendations In this study, super- insulation and air- tightness, high efficiency solar collector, heat recovery ventilation(HRV) system, active and passive solar heating system, energy efficient heating and cooling system and their integration were studied, both as a group and individually, for the purpose of 70% self- sufficient low energy house development. The low energy house for the experimental testing were designed as a result. The main result are : (I) Super- insulation and air- tightness The most important factors in super- insulated thermal envelope design are as follows: - Low heat transfer - Minimize air leakage and draft - Protect building material from moisture damage Heat transmission coefficient(K) of thermal envelope is under 0.15(Kcal/m2.h ). Exterior insulation system is better than interior insulation system in aspect of indoor temperature fluctuation, heat bridge & surface condensation and corner heat loss coefficient of exterior insulation system is smaller than that of interior & middle insulation system. At the weak point of heat bridge, that is, bracket for exterior finish material, bottom of beam & interior side of beam around opening, insulation should be added. Air/vapor barrier should be installed inside insulation and the best material is 0.03 0.05mm polyethylene film. At the joint between two sheets of poly ethylene, the two sheets should be overlapped by 50 150 mm. For airtightness, - Reducing the number and size of openings - Installing air/vapor barrier - Sealing corner(wall to roof, wall to floor) - Detailed construction of electrical box, piping sleeve, & etc. (II) Heat Recovery Ventilation(HRV) System In the first year study, data survey and performance analysis are carried out for the heat recovery ventilation system. Also the effective flow path and network system for ventilation in the residential house are examined. The floor supply and ceiling exhaust type shows the most effective velocity and temperature distributions from the numerical simulation, but supply and exhaust through the ceiling is desirable in the view of conventional life style and space utilization. As the temperature performance of heat recovery ventilation system is about 95% in experiment, outdoor air can be supplied to the living space directly without feeling of cold draft and need of extra preheating system. So this can increase the fresh warm outdoor air efficiently for the good indoor air quality when the lack of the required ventilation causes the increase of contaminant in the high air tightness residential house. The supply inlet position of fresh outdoor air warmed by the stale exhaust air is desirable to be located opposite of the door in the clear zone for the effective ventilation flow path. According to the space allocation, insufficient case of ventilation happens. More fresh outdoor air required to resident may be needed than the design ventilation flow rate, so optimum space allocation to the flow path is important also. In the second year, through the experiment and performance analysis, various heat recovery ventilation systems equipped with the several flow path and system network will be studied continuously. And calculation technology of heat exchange and recycled amount and optimum system will be developed. (III) Development of High Efficiency Solar Collector The natural convection in the air gap between the cover glass and absorber plate of a flat- plate solar collector occurs, which takes large part of heat losses. So suppression of natural convection offers good possibilities to improve the efficiency of collector. In this study, analysis and experiment for a flat- plate solar collector with TIM were carried out to evaluate the performance of solar collector. In order to suppress the natural convection, square cell honeycomb structure(9mm x 9mm) of Celluloseacetate and capillary structure (3.5mm) of Polycarbonate as TIM(Transparent Insulation Material) were used in analysis and experiment. Analytical results show good agreement with experimental ones. They have about 7 % discrepancy for square cell honeycomb structure, and about 3 % for capillary structure respectively. Heat losses in TI- collector decrease about 29 % for square cell honeycomb structure, and about 25 % for capillary structure respectively compared with those of the ordinary flat- plate solar collector. The collector efficiency of square cell honeycomb structure shows better than that of the capillary structure. It is considered that decrease in transmittance due to smaller cavity has more effect on collector efficiency than that in the heat losses due to the natural convection. From the simple calculation for the annual solar gain of TI- collector(tilt angle : 45 ) using the empirical relation of collector efficiency, it shows about 20 % higher than that of the ordinary flat- plate solar collector. (IV) Integration of Key Design Issue and the Passive Solar System, and the Performance Evaluation The ZeSH, that is applied the several energy conservation technologies was designed and analyzed thermally, as a group and individually, for the optimization of major design parameters that influence on the heating and cooling load. Table 1 shows the comparing of the heating load, the energy saving and the saving fraction for the reference model and several ZeSHs that are applied different kind of design parameters. The results are as follows : - The most important design parameter on the energy saving is a super- insulation. It can be saved 49% of heating load by it comparing to the reference model. - The energy saving effect by the other design parameters are following : 15% by the super- window 8 to 13% by passive solar system with 15 collecting area and tromb wall and 5% further by TIM instead of single- window mass wall in this system. 4- 5% by the sun- space - The sunspace must be used for the preheating device of fresh air supplying into the house. - The ZeSH is expected to reduce 65% to 92% of the heating load according to the how combined the unit design parameters. The ZeSH that is designed here can reduced 82% of the heating load without the active solar system, the heat recovery ventilation system and preheating of a fresh air by sun space. So it is expected the further reduction of heating load by these three system.
Heating energy consumption according to the application of key design issues (House heating area : 138.6 ) Applicationtechnology Totalspaceheating Saving (kWh/ ) Saving fracion (% )(kWh) (kWh/ ) Referencemodel 12,379 89.3 - - Analysisof individual technology Superinsulation 6,417 46.3 46.03 49% Superwindow 10,570 76.3 13.1 15% Air infiltration rate 0.1time/ h 7,923 57.2 32.15 36% 0.3time/ h 10,235 73.9 15.5 17% passive system MassWallwithsingle glass(15 ) 11,392 82.2 7.1 8% MassWallwithdoubleglasses andLow-emisivityfilm (15 ) 11,114 80.2 9.1 10% MassWallwittTIM (15 ) 10,684 77.0 12.2 13% Attached green- house no preheating ventilation doubleglasses 12,379 89.3 - - TIM 12,401 89.5 -0.02 -1% preheating ventilation doubleglasses 11,912 86.0 3.3 4% TIM 11,332 85.2 4.1 5% Integrated analysis superinsulation+infiltration0.1time/ hr 2,683 19.4 70.0 79% superinsulation+ infiltration0.3time/ h 4,357 31.4 57.9 65% superinsulation+ infiltration0.1time/ h+ super-window 1,195 8.6 80.7 90% superinsulation+ infiltration0.3time/ h+ super-window 2,851 20.6 68.7 77% superinsulation+ infiltration0.1time/ h+ super-window+TIM 969 7.0 82.3 92% superinsulation+ infiltration0.3time/ h+ super-window+TIM 2,266 16.4 73.0 81.6 (V) Active Solar System & Efficient Heating and Cooling System The active solar heating system with heat pump as an auxiliary heater for ZeSH was investigated. As a result, the solar assisted heat pump(SAHP) and the ground source heat pump(GSHP) system were evaluated as an efficient heating and cooling system for the ZESH because heat pump is useable for both heating and cooling and also has a high COP if there is a optimum heat source. The low temperature of solar thermal energy and ground source that can not be use directly for heating and cooling is a good heat source of heat pump. In this study the active solar heating system combined to the heat pump was designed and then analyzed by computer simulation as well as experiment. The results are : - the yearly solar fraction is 81% with a 28 m^2 of solar collector area. - the COP of GSHP is about 3. - the COP of SAHP is about 3.5 to 4.5. - the parametric study as the influence of storage volume and collector area on the system performance was carried out.
목차 Contents
제 1 장 서 론...32
제1절 연구배경 및 필요성...32 제2절 연구목표...33 제3절 연구내용 및 방법...34
제 2 장 에너지자립주택 개발기술의 접근방법...37
제1절 태양열 건물의 에너지자립 설계기법 및 핵심기술 분야...37
1. 효과적인 태양열 건물의 설계 접근방법...37 2. 핵심기술분야 및 에너지자립 태양열건물 접근방법...39
제2절 Road map...41
1. 연구사업 최종목표를 위한 Road Map 수립...41
제 3 장 고단열외피 시스템...46
제1절 국내외 관련연구...46
1. 국내외 에너지절약형 건물 현황...46 2. 관련 주요연구 동향...52
제2절 초단열주택 설계...54
1. 목표설정...55 2. 예비설계(preliminary design)...57 3. 예비 에너지관련 사양 선택...62 4. 예비 에너지해석...64 5. 에너지시스템 요소 설계(energy system component design)...66 6. 시공도서(Construction Document) 작성...66
※ AI-Helper는 부적절한 답변을 할 수 있습니다.