양방향재하시험장치 위치선정을 위한 발휘단위주면마찰력과 단위선단지지력 산정연구 Evaluation of acting unit point load and acting unit side resistanc for bi-directional loading device location원문보기
대형구조물의 시공의 증가로 인해, 말뚝의 지지력확보를 위한 현장타설말뚝은 대구경화, 대심도화 되고 있는 실정이다. 또한 지지력확보를 위한 근입심도가 깊어짐에 따라서 선단지지력에 비해 주면마찰력이 높게 발휘됨으로써, 주면마찰력의 영향을 많이 받게 된다. 양방향 재하시험 장치 위치균형에 따라 단위 주면 마찰력과 단위 선단지지력의 산정이 달라질 수 있다고 볼 수 있으며, 이는 즉 말뚝의 지지력산정에 큰 영향을 미친다고 볼 수 있다. 하지만 실제로 양방향 재하시험사례를 분석해보면 발휘단위주면마찰력과 발휘단위선단지지력으로 상향 지지력과 하향 지지력을 계산하는데 각각의 지층에서 작용되는 변위가 달라 발휘단위주면마찰력과 단위 선단지지력 산정을 위한 양방향 재하시험 장치의 위치선정은 쉽지 않다. 따라서 본 연구에서는 국내에서 시행되었던 양방향재하시험 사례에서 얻은 각 지층별의 실측 ...
대형구조물의 시공의 증가로 인해, 말뚝의 지지력확보를 위한 현장타설말뚝은 대구경화, 대심도화 되고 있는 실정이다. 또한 지지력확보를 위한 근입심도가 깊어짐에 따라서 선단지지력에 비해 주면마찰력이 높게 발휘됨으로써, 주면마찰력의 영향을 많이 받게 된다. 양방향 재하시험 장치 위치균형에 따라 단위 주면 마찰력과 단위 선단지지력의 산정이 달라질 수 있다고 볼 수 있으며, 이는 즉 말뚝의 지지력산정에 큰 영향을 미친다고 볼 수 있다. 하지만 실제로 양방향 재하시험사례를 분석해보면 발휘단위주면마찰력과 발휘단위선단지지력으로 상향 지지력과 하향 지지력을 계산하는데 각각의 지층에서 작용되는 변위가 달라 발휘단위주면마찰력과 단위 선단지지력 산정을 위한 양방향 재하시험 장치의 위치선정은 쉽지 않다. 따라서 본 연구에서는 국내에서 시행되었던 양방향재하시험 사례에서 얻은 각 지층별의 실측 SPT N과 보정 N치를 이용하여 실제 사용말뚝의 재하장치 위치선정을 위한 발휘단위 주면 마찰력과 발휘단위 선단지지력을 선정을 위한 관계도표를 확립하고, 이를 통해 선정된 균형위치에 양방향 재하장치 설치 후 재하시험을 실시하여 측정된 각 지층의 단위주면마찰력과 단위 선단지지력과 보정된 N값 관계도표 값들을 비교하여 재하시험 위치 선정을 위한 발휘단위주면마찰력과 단위 선단지지력의 적정성을 분석하였다.
대형구조물의 시공의 증가로 인해, 말뚝의 지지력확보를 위한 현장타설말뚝은 대구경화, 대심도화 되고 있는 실정이다. 또한 지지력확보를 위한 근입심도가 깊어짐에 따라서 선단지지력에 비해 주면마찰력이 높게 발휘됨으로써, 주면마찰력의 영향을 많이 받게 된다. 양방향 재하시험 장치 위치균형에 따라 단위 주면 마찰력과 단위 선단지지력의 산정이 달라질 수 있다고 볼 수 있으며, 이는 즉 말뚝의 지지력산정에 큰 영향을 미친다고 볼 수 있다. 하지만 실제로 양방향 재하시험사례를 분석해보면 발휘단위주면마찰력과 발휘단위선단지지력으로 상향 지지력과 하향 지지력을 계산하는데 각각의 지층에서 작용되는 변위가 달라 발휘단위주면마찰력과 단위 선단지지력 산정을 위한 양방향 재하시험 장치의 위치선정은 쉽지 않다. 따라서 본 연구에서는 국내에서 시행되었던 양방향재하시험 사례에서 얻은 각 지층별의 실측 SPT N과 보정 N치를 이용하여 실제 사용말뚝의 재하장치 위치선정을 위한 발휘단위 주면 마찰력과 발휘단위 선단지지력을 선정을 위한 관계도표를 확립하고, 이를 통해 선정된 균형위치에 양방향 재하장치 설치 후 재하시험을 실시하여 측정된 각 지층의 단위주면마찰력과 단위 선단지지력과 보정된 N값 관계도표 값들을 비교하여 재하시험 위치 선정을 위한 발휘단위주면마찰력과 단위 선단지지력의 적정성을 분석하였다.
With growing of civil structures in order to obtain the Load-bearing capacity of piles , foundations have getting bigger and deeper. When foundations have getting deeper for obtaining load-bearing capacity, the unit side resistance is higher than the unit end bearing capacity. Success or failure of ...
With growing of civil structures in order to obtain the Load-bearing capacity of piles , foundations have getting bigger and deeper. When foundations have getting deeper for obtaining load-bearing capacity, the unit side resistance is higher than the unit end bearing capacity. Success or failure of the bi-directional test for drilled shaft depends on point selection for loading cells, that is balanced location both uplift force and downward force. but methods to evaluate the unit side resistance in rockmass layer in both domestic and foreign are based on the uniaxial compression strength of rock core, which can hardly be obtained in domestic rockmass layers which are weathered rockmass layer and soft rockmass layer with very low RQD. Therefore, this study suggested the relation charts between the revised SPT N values and unit side resistance of each different layers, which were obtained from bi-directional pile load tests in various domestic sites. To evaluate the appropriateness of the relation charts, the estimated unit side resistances from the relation charts were used to select the loading cell position and compared with the measured unit side resistances from field pile load test. In this study, measured unit side resistances, which are from bi-directional loading tests performed on more than 50 site, are compared with values from several suggested methods.
With growing of civil structures in order to obtain the Load-bearing capacity of piles , foundations have getting bigger and deeper. When foundations have getting deeper for obtaining load-bearing capacity, the unit side resistance is higher than the unit end bearing capacity. Success or failure of the bi-directional test for drilled shaft depends on point selection for loading cells, that is balanced location both uplift force and downward force. but methods to evaluate the unit side resistance in rockmass layer in both domestic and foreign are based on the uniaxial compression strength of rock core, which can hardly be obtained in domestic rockmass layers which are weathered rockmass layer and soft rockmass layer with very low RQD. Therefore, this study suggested the relation charts between the revised SPT N values and unit side resistance of each different layers, which were obtained from bi-directional pile load tests in various domestic sites. To evaluate the appropriateness of the relation charts, the estimated unit side resistances from the relation charts were used to select the loading cell position and compared with the measured unit side resistances from field pile load test. In this study, measured unit side resistances, which are from bi-directional loading tests performed on more than 50 site, are compared with values from several suggested methods.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.