연속주조 방법을 이용하여 판재로 제조한 AM50 마그네슘 합금을 균질화 처 리와 압연 그리고 어닐링하여 최종제품을 제작하였다. 이 시험편을 고온변형시험 기(Gleeble System)를 이용하여 100~300℃의 온도에서 변형률 속도 10-3s-1으 로 ...
연속주조 방법을 이용하여 판재로 제조한 AM50 마그네슘 합금을 균질화 처 리와 압연 그리고 어닐링하여 최종제품을 제작하였다. 이 시험편을 고온변형시험 기(Gleeble System)를 이용하여 100~300℃의 온도에서 변형률 속도 10-3s-1으 로 인장시험을 하여 기계적 성질을 조사하였다. 기존의 마그네슘 합금과는 달리, 200℃ 보다 변형 온도가 낮아질수록 강도와 연신율이 함께 증가하였고, 125℃ 에서 최대 연신율을 나타냈다. 시험 온도를 다르게 하여 시험편들을 변형시키면 서 유동의 각 단계 - 항복, 소성, 파괴 단계에서 EBSD를 이용하여 미세조직과 집합조직을 조사하여 기계적성질과의 상관관계를 고찰하였다.
연속주조 방법을 이용하여 판재로 제조한 AM50 마그네슘 합금을 균질화 처 리와 압연 그리고 어닐링하여 최종제품을 제작하였다. 이 시험편을 고온변형시험 기(Gleeble System)를 이용하여 100~300℃의 온도에서 변형률 속도 10-3s-1으 로 인장시험을 하여 기계적 성질을 조사하였다. 기존의 마그네슘 합금과는 달리, 200℃ 보다 변형 온도가 낮아질수록 강도와 연신율이 함께 증가하였고, 125℃ 에서 최대 연신율을 나타냈다. 시험 온도를 다르게 하여 시험편들을 변형시키면 서 유동의 각 단계 - 항복, 소성, 파괴 단계에서 EBSD를 이용하여 미세조직과 집합조직을 조사하여 기계적성질과의 상관관계를 고찰하였다.
AM50 Mg alloy sheet was fabricated through the processes such as continuous casting, rolling and annealing. In the sheet samples of the final product, the tensile tests were carried out at different temperatures ranging between 100 and 300˚C. The samples deformed below 200˚C revealed the work harden...
AM50 Mg alloy sheet was fabricated through the processes such as continuous casting, rolling and annealing. In the sheet samples of the final product, the tensile tests were carried out at different temperatures ranging between 100 and 300˚C. The samples deformed below 200˚C revealed the work hardening in the flow curves, and the maximum elongation (about 80.5%) appeared when the sample tested at 125˚C. This extraordinary phenomenon was discussed in terms of textures and microstructures examined using the electron back scattering diffraction (EBSD) technique in the samples taken at different stages of deformation during the tensile test.
AM50 Mg alloy sheet was fabricated through the processes such as continuous casting, rolling and annealing. In the sheet samples of the final product, the tensile tests were carried out at different temperatures ranging between 100 and 300˚C. The samples deformed below 200˚C revealed the work hardening in the flow curves, and the maximum elongation (about 80.5%) appeared when the sample tested at 125˚C. This extraordinary phenomenon was discussed in terms of textures and microstructures examined using the electron back scattering diffraction (EBSD) technique in the samples taken at different stages of deformation during the tensile test.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.