본 연구에서는 표면거칠기와 근입비, 직경에 따른 파이프형 앵커의 인발거동을 평가하기 위하여 실내모형실험이 시행되었다. 수직방향의 지반 변형에서 매입된 파이프형 앵커의 설계는 파이프에 부과된 힘의 크기에 의해 지배받는다. 본 논문에서는 모형실험의 분석을 통하여 파이프 직경과 표면 거칠기, 근입비와 지반상태로 야기된 파이프형 앵커의 변위 특성과 극한 저항력을 비교하고 평가하였다. 실험결과는 상대밀도의 증가에 따라 극한 인발력이 20%가량 증가하고 있음을 보여주고 있다. 지반의 상대밀도와 파이프의 지름, 표면거칠기의 변화에 따른 파이프형 앵커의 파괴시 변위는 근입비가 2에서 8로 증가함에 따라 약 5배 정도의 증가 경향을 보였다. 또한 앵커이론에 근거한 이론식들은 인발계수를 과대평가하는 것으로 나타났다.
본 연구에서는 표면거칠기와 근입비, 직경에 따른 파이프형 앵커의 인발거동을 평가하기 위하여 실내모형실험이 시행되었다. 수직방향의 지반 변형에서 매입된 파이프형 앵커의 설계는 파이프에 부과된 힘의 크기에 의해 지배받는다. 본 논문에서는 모형실험의 분석을 통하여 파이프 직경과 표면 거칠기, 근입비와 지반상태로 야기된 파이프형 앵커의 변위 특성과 극한 저항력을 비교하고 평가하였다. 실험결과는 상대밀도의 증가에 따라 극한 인발력이 20%가량 증가하고 있음을 보여주고 있다. 지반의 상대밀도와 파이프의 지름, 표면거칠기의 변화에 따른 파이프형 앵커의 파괴시 변위는 근입비가 2에서 8로 증가함에 따라 약 5배 정도의 증가 경향을 보였다. 또한 앵커이론에 근거한 이론식들은 인발계수를 과대평가하는 것으로 나타났다.
In this study, laboratory model test was performed to estimate pullout behavior of pipe type anchor with surface roughness, embedment and diameter. The design of buried pipe anchors in areas of vertical ground movement is governed, in part, by magnitude of the forces imposed on the pipe and displace...
In this study, laboratory model test was performed to estimate pullout behavior of pipe type anchor with surface roughness, embedment and diameter. The design of buried pipe anchors in areas of vertical ground movement is governed, in part, by magnitude of the forces imposed on the pipe and displacements at which they are developed. In this paper, uplift resistance and displacement characteristics of pipe anchors caused by ground condition and embedment ratio, surface roughness, pipe diameter through the analysis of pipe anchor model test were compared and analyzed. The test results of the buried pipe showed that as the relative density increases, ultimate uplift resistance increase in 20%. When pipe anchor is failed with the relative density of the ground, the change of surface roughness, it was shown that the deformation increases as the ratio of penetration increases from 2 to 8 in five times approximately. And most anchor-based theories overestimate the breakout factor.
In this study, laboratory model test was performed to estimate pullout behavior of pipe type anchor with surface roughness, embedment and diameter. The design of buried pipe anchors in areas of vertical ground movement is governed, in part, by magnitude of the forces imposed on the pipe and displacements at which they are developed. In this paper, uplift resistance and displacement characteristics of pipe anchors caused by ground condition and embedment ratio, surface roughness, pipe diameter through the analysis of pipe anchor model test were compared and analyzed. The test results of the buried pipe showed that as the relative density increases, ultimate uplift resistance increase in 20%. When pipe anchor is failed with the relative density of the ground, the change of surface roughness, it was shown that the deformation increases as the ratio of penetration increases from 2 to 8 in five times approximately. And most anchor-based theories overestimate the breakout factor.
※ AI-Helper는 부적절한 답변을 할 수 있습니다.