[논문]A Study on Vehicle-based Durability Evaluation for Weight-reduced Valve Parts of the Dual Clutch Transmission

ChanEun Kim; TaeWook Kim

doi:10.9725/kts.2024.40.1.24

A Study on Vehicle-based Durability Evaluation for Weight-reduced Valve Parts of the Dual Clutch Transmission 원문보기

한국트라이볼로지학회지 = Tribology and lubricants, v.40 no.1, 2024년, pp.24 - 27

ChanEun Kim (Graduate School, Development of Precision Mechanical Engineering, Kyungpook National University) , TaeWook Kim (Development of Precision Mechanical Engineering, Kyungpook National University)

Abstract ▼ AI-Helper

A monotype valve body for a dual clutch transmission has the potential to reduce costs, weight, and manufacturing time by modularizing various parts, including those of existing solenoid packs and valve bodies, into one through the application of super-precision die casting technology. However, this approach may lead to challenges such as reduced rigidity and increased interference due to modularization and compactness, impacting both product performance due to the reduced weight as well as durability and reliability. Unlike existing products, this approach requires a high-precision thin-wall block to avoid more complicated flow line formation, interference between flow lines, and leaks, as well as a strict quality requirement standard and precise inspections including detection of internal defects. To conduct precise inspections, we built an equivalent model corresponding to a driving distance of 300,000 km. Testing involved simulating actual road loads using a real vehicle and a chassis dynamometer in the FTP-75 mode (EPA Federal Test Procedure). The aim of the study was to establish a vehicle load-based part durability model for manufacturing a mono-type valve body and to develop fundamental technology for part weight reduction through preliminary design by introducing analytical weight reduction technology based on the derived results.

주제어

표/그림 (6)

그림 Fig. 1. FTP 75 base DCT valve-body working test bench.
표 Table 1. Specifications of testing chassis dynamometer
그림 Fig. 2. DCT actuation on FTP-75 mode to extend 300K equivalent load cycle.
그림 Fig. 3. Fatigue base analysis for mono valve body target model.
그림 Fig. 4. Boundary conditions of hydraulic load according to clutch actuation.
그림 Fig. 5. Weight reduction capability demonstration based on over design safety factor(SF = 5.07).

AI 본문요약
AI-Helper

제안 방법

It must be accompanied by a durability examination of the hydraulic load related to clutch actuator operation. In this study, the durability mode corresponding to 300,000 km driving of the DCT actuator was derived based on the actual vehicle load RLDA of the FTP75 mode, and the fatigue analysis was performed on the target model based on the derived durability mode. It was found from the analysis that additional weight reduction of the thin-wall block was available according to the result of over-design since the safety factor exceeded 5.
This study provided a methodological discussion of the weight reduction of a valve body, a key component of a wet type DCT. In particular, when designing an actuator body as a mono type valve body by applying a method different from the existing method by which the actuator body is manufactured and assembled separately.
However, concerns about the failure to ensure safety (reliability verification) are increasing due to the rigidity reduction caused by the structure of the mono valve body that gradually becomes complicated due to integration as well as the attempt for additional weight reduction (Woo, 2009). This study will discuss the technology of building the equivalent durability mode to that of an actual vehicle based on operation load of 300,000 km for the mono type valve body housing on which the actuator body is combined and integrated with the wet type DCT valve body along with securing the corresponding safety requirements. Based on this result, this study will discuss the weight reduction technology of the die cast housing responding to the fatigue strength safety over an operation load of 300,000 km.

대상 데이터

Table 1 indicates the specification of the chassis dynamometer used. The vehicle used for the test is an AVANTE AD 1.6 e-VGT equipped with a 7-speed automatic DCT. Vehicle speed, engine RPM, and brake ON/OFF signals were measured via the CAN port of the OBED2 terminal.

성능/효과

In Fig. 4, the boundary condition is set for the working flow line based on the working pressure applied to the mono valve body housing during actuator operation, and the load condition of the 16bar is set to be applied to the pressurized hydraulic path.
07180), indicating that an excessive design condition was applied. Based on these results, it can be seen that the additional weight reduction design will be available for the thin-wall block.
22 km) and the clutch working frequency count, if calculated according to the vehicle's warranty period (a driving distance of 300,000 km), indicates a 1,034,482 working count during the warranty period. From this working count, subtract 34,482 and regard the 1,000,000 working count as the durability limit standard of a DCT part with a warranty of 300,000 km driving distance, and use these values as the basis for the design improvement for the fatigue analysis base and weight reduction of the mono valve body housing.
Given the hydraulic load within the Valve body, it was found that the stress and deformation existed within the material’s safe stress and strain area sufficiently and that the fatigue-based safety ratio was very high (SF=5.07180), indicating that an excessive design condition was applied
In this study, the durability mode corresponding to 300,000 km driving of the DCT actuator was derived based on the actual vehicle load RLDA of the FTP75 mode, and the fatigue analysis was performed on the target model based on the derived durability mode. It was found from the analysis that additional weight reduction of the thin-wall block was available according to the result of over-design since the safety factor exceeded 5.0. In addition, it is thought to be possible to infer an additional reduction point besides the wall face through this methodological approach and that it can be utilized as a useful weight reduction design method at the initial design stage through analysis.
The total time required is 1,874sec. The motorway driving mode uses a warmed up engine and drives at a maximum speed of 97 km/h and an average speed of 77 km/h over a distance greater than 16 km, and the car does not stop. The total distance is 16.
The total driving distance for the FTP-75 road is 17.77+16.45 km (34.22 km) and the clutch working frequency count, if calculated according to the vehicle's warranty period (a driving distance of 300,000 km), indicates a 1,034,482 working count during the warranty period
1 km/h. The total time required is 1,874sec. The motorway driving mode uses a warmed up engine and drives at a maximum speed of 97 km/h and an average speed of 77 km/h over a distance greater than 16 km, and the car does not stop.
2 shows the gear stage for each driving mode according to the FTP-75 and the shifting count at this time. The use count for each clutch identified through the shifting pattern is 80+30+8 count for Clutch 1 (total of 118), and 80+30+8 for Clutch 2 (total of 118). The total driving distance for the FTP-75 road is 17.

후속연구

This study will discuss the technology of building the equivalent durability mode to that of an actual vehicle based on operation load of 300,000 km for the mono type valve body housing on which the actuator body is combined and integrated with the wet type DCT valve body along with securing the corresponding safety requirements. Based on this result, this study will discuss the weight reduction technology of the die cast housing responding to the fatigue strength safety over an operation load of 300,000 km. It is thought that such a technological leap will work advantageously for the safe settlement of the wet type DCT technology in Korea, or will contribute to the marketing power for obtaining orders by offering customer friendly proposals to vehicle makers and transmission manufacturers.
0. In addition, it is thought to be possible to infer an additional reduction point besides the wall face through this methodological approach and that it can be utilized as a useful weight reduction design method at the initial design stage through analysis.
Based on this result, this study will discuss the weight reduction technology of the die cast housing responding to the fatigue strength safety over an operation load of 300,000 km. It is thought that such a technological leap will work advantageously for the safe settlement of the wet type DCT technology in Korea, or will contribute to the marketing power for obtaining orders by offering customer friendly proposals to vehicle makers and transmission manufacturers.
It is thought that the methodological results of this study can be used as a logical basis for the weight reduction of parts when performing additional weight reduction in the future.
In particular, when designing an actuator body as a mono type valve body by applying a method different from the existing method by which the actuator body is manufactured and assembled separately. It must be accompanied by a durability examination of the hydraulic load related to clutch actuator operation. In this study, the durability mode corresponding to 300,000 km driving of the DCT actuator was derived based on the actual vehicle load RLDA of the FTP75 mode, and the fatigue analysis was performed on the target model based on the derived durability mode.

참고문헌 (6)

Kim, T. H, Kim, C. K., Studies on The Stress Characteristic of LPG Valve with Body Shap, Kigas？2014 Annual Autumn Conference, pp.102-105, 2014.
Lee, G. C, Kim, J. Y., Na, B.C., A Study on the？Lubrication Flow Distribution in a Six-speed Automatic Transmission Valve Body, The Trans. Korean？Society of Mechanical Technology, Vol.13, No.2,？pp.79-84, 2011.
Lee, Y. J, Kim, G. C., Pyo, Y. D., Sunwoo, M. H.,？Eom, M. D., Development of Chassis Dynamometer？Test Modes to Derive the Emission Factors for？Light Duty Vehicles, The Trans. Korean Society of？Automotive Engineers. Vol.10, No.6, pp.117-124,？2002.
Na, B. C., Design Improvement of High Pressure？Fuel Pump for gasoline direct injection Engines,？PROCEEDINGS OF THE INSTITUTION OF？MECHANICAL ENGINEERS, ImechE, Journal of？Automotive Engineering, Vol.216, pp.83-90, 2002.
Seo, J. H, Na, B. C., A study on the Tribology？Behavior of Valve train System by Low friction Coating, Advanced Materials Research, Vol.47, No.50,？pp.1470-1473, 2008.
Woo, Y. C., A Study on Valve Body Surface Pressure Distribution and Valve Interference, KSAE？2009 Annual Autumn Conference and Exhibition.？Pp.362-365, 2009.

표제어: PCR

동의어: Packet Collision Rate

용어 설명 출처 목록 (6)

용어 설명: PCR은 세균 특이성이 있는 primer를 이용하여 적은 수의 세균이 있을지라도 쉽게 검출할 수 있는 유용한 방법이며, 이를 이용하여 구강 내 치면세균막이나 타액에서 직접 세균을 검출할 수 있게 되었다[8].

내보내기 구분	파일저장 인쇄 메일전송
구성항목	기본정보 상세정보 관리번호, 논문명, 저널/프로시딩명, 저자 , 발행년, 권, 호, 시작페이지, 끝페이지, 발행기관 관리번호, 논문명, 대등논문명, 저자 , 저널/프로시딩명, 발행기관, 발행년, 발행언어, 권, 호, 시작페이지, 끝페이지, ISBN, ISSN, 주제분야, 키워드, 초록(한글), 초록(영문), 저자(소속기관)
저장형식	Text(ASCII format) Excel format RefWorks Direct Export RIS format (for Reference Manager, ProCite, EndNote), Scholar's Aids, Mendeley
메일정보	받는사람 (필수) @ 보내는사람 (선택) @ 제목 내용 KISTI 검색결과 이메일 서비스
안내	총 건의 자료가 검색되었습니다. 다운받으실 자료의 인덱스를 입력하세요. (1-10,000) 검색결과의 순서대로 최대 10,000건 까지 다운로드가 가능합니다. 데이타가 많을 경우 속도가 느려질 수 있습니다.(최대 2~3분 소요) 다운로드 파일은 UTF-8 형태로 저장됩니다. 파일의 내용이 제대로 보이지 않을실 때는 웹브라우저 상단의 보기 -> 인코딩 -> 자동선택 여부를 확인하십시오. ~ Text(ASCII format) Excel format

연합인증