[논문]Optimum design of the carbon composite bipolar plate (BP) for the open cathode of an air breathing PEMFC

Kim, Minkook; Lee, Dai Gil

doi:10.1016/j.compstruct.2015.12.061

Optimum design of the carbon composite bipolar plate (BP) for the open cathode of an air breathing PEMFC

Composite structures, v.140, 2016년, pp.675 - 683

Kim, Minkook (Corresponding author. Tel.: +82 42 350 3221) , Lee, Dai Gil (fax: +82 42 350 5221.)

Abstract ▼ AI-Helper

The proton exchange membrane fuel cells (PEMFCs) are a promising source of portable power due to its high energy density, low emissions and wide power range. However, PEMFCs have some limitations for portable applications because of the supplementary power consumption and the mass increase by balance of plants, such as the fuel pump, air compressor and humidifier. In this study, a light mass PEMFC system was developed using carbon composite bipolar plates (BPs) and an air breathing stack design with open cathode channel configurations to reduce the mass of the stack. However, under the high compaction pressure, the failure occurred in the carbon composite BPs for the open cathode. To enhance the durability of the BP against the compaction pressure, the finite element analysis, the compressive test and the fracture toughness test were performed. The maximum compaction pressure on the BP was calculated by applying the maximum strain failure criterion to the composite BP. Then, the optimum thickness and stacking sequence of the open cathode bipolar plate were determined by considering the mass and the maximum compaction pressure. (C) 2016 Elsevier Ltd. All rights reserved.

주제어

참고문헌 (22)

Appleby 1987 Fuel cells: trends in research and application
Barbir 2005 PEM fuel cells: theory and practice
Hoogers 2002 Fuel cell technology handbook
2003 Fuel cell systems explained
Renewable Energy Al-Baghdadi 34 1812 2009 10.1016/j.renene.2008.12.002 Performance comparison between airflow-channel and ambient air-breathing PEM fuel cells using three-dimensional computational fluid dynamics models

상세보기
J Power Sources Sridhar 101 72 2001 10.1016/S0378-7753(01)00625-5 Humidification studies on polymer electrolyte membrane fuel cell

상세보기
Int J Hydrogen Energy Ous 34 3476 2009 10.1016/j.ijhydene.2009.02.037 The formation of water droplets in an air-breathing PEMFC

상세보기
Int J Hydrogen Energy Yang 33 2795 2008 10.1016/j.ijhydene.2008.03.025 A preliminary study of a six-cell stack with dead-end anode and open-slits cathode

상세보기
Int J Hydrogen Energy Santa Rosa 32 4350 2007 10.1016/j.ijhydene.2007.05.042 High performance PEMFC stack with open-cathode at ambient pressure and temperature conditions

상세보기
J Power Sources Hottinen 129 68 2004 10.1016/j.jpowsour.2003.11.012 Evaluation of planar free-breathing polymer electrolyte membrane fuel cell design

상세보기
World Electr Veh J Matsunaga 3 820 2009 10.3390/wevj3040820 Powertrain system of honda FCX clarity fuel cell vehicle

상세보기
J Power Sources Yu 189 929 2009 10.1016/j.jpowsour.2008.12.106 Integrated carbon composite bipolar plate for polymer-electrolyte membrane fuel cells

상세보기
Compos Struct Yu 94 1911 2012 10.1016/j.compstruct.2011.12.024 Plasma treatment of the carbon fiber bipolar plate for PEM fuel cell

상세보기
Compos Struct Kim 96 569 2013 10.1016/j.compstruct.2012.09.017 Bipolar plates made of carbon fabric/phenolic composite reinforced with carbon black for PEMFC

상세보기
Int J Hydrogen Energy Kim 37 4300 2012 10.1016/j.ijhydene.2011.11.125 Bipolar plates made of plain weave carbon/epoxy composite for proton exchange membrane fuel cell

상세보기
J Power Sources Lee 145 353 2005 10.1016/j.jpowsour.2005.02.057 Analyses of the fuel cell stack assembly pressure

상세보기
Int J Hydrogen Energy Hwang 33 3801 2008 10.1016/j.ijhydene.2008.04.043 Development of a small vehicular PEM fuel cell system

상세보기
Int J Hydrogen Energy Chi 35 2936 2010 10.1016/j.ijhydene.2009.05.066 On the effects of non-uniform property distribution due to compression in the gas diffusion layer of a PEMFC

상세보기
J Fuel Cell Sci Technol Li 11 2014 10.1115/1.4027253 Effect of compressive pressure on the contact behavior between bipolar plate and gas diffusion layer in a proton exchange membrane fuel cell

상세보기
J Fuel Cell Sci Technol Mishra 1 2 2004 10.1115/1.1782917 Measurement and prediction of electrical contact resistance between gas diffusion layers and bipolar plate for applications to PEM fuel cells

상세보기
J Adhes Sci Technol Yoon 24 429 2010 10.1163/016942409X12541266699635 Improvement of the adhesive fracture toughness of bonded aluminum joints using E-glass fibers at cryogenic temperature

상세보기
Isr J Technol Liebowitz 17 273 1979 Mechanics of fracture - fundamentals and some recent developments

LOADING...

내보내기 구분	파일저장 인쇄 메일전송
구성항목	기본정보 상세정보 관리번호, 논문명, 저널/프로시딩명, 저자 , 발행년, 권, 호, 시작페이지, 끝페이지, 발행기관 관리번호, 논문명, 대등논문명, 저자 , 저널/프로시딩명, 발행기관, 발행년, 발행언어, 권, 호, 시작페이지, 끝페이지, ISBN, ISSN, 주제분야, 키워드, 초록(한글), 초록(영문), 저자(소속기관)
저장형식	Text(ASCII format) Excel format RefWorks Direct Export RIS format (for Reference Manager, ProCite, EndNote), Scholar's Aids, Mendeley
메일정보	받는사람 (필수) @ 보내는사람 (선택) @ 제목 내용 KISTI 검색결과 이메일 서비스
안내	총 건의 자료가 검색되었습니다. 다운받으실 자료의 인덱스를 입력하세요. (1-10,000) 검색결과의 순서대로 최대 10,000건 까지 다운로드가 가능합니다. 데이타가 많을 경우 속도가 느려질 수 있습니다.(최대 2~3분 소요) 다운로드 파일은 UTF-8 형태로 저장됩니다. 파일의 내용이 제대로 보이지 않을실 때는 웹브라우저 상단의 보기 -> 인코딩 -> 자동선택 여부를 확인하십시오. ~ Text(ASCII format) Excel format

연합인증

Optimum design of the carbon composite bipolar plate (BP) for the open cathode of an air breathing PEMFC

Abstract ▼ AI-Helper

주제어

참고문헌 (22)

이 논문을 인용한 문헌

연구과제 타임라인

관련 콘텐츠

원문 URL 링크

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트

연합인증

Optimum design of the carbon composite bipolar plate (BP) for the open cathode of an air breathing PEMFC

Abstract ▼ AI-Helper

주제어

참고문헌 (22)

이 논문을 인용한 문헌

연구과제 타임라인

전체(0) 논문(0) 특허(0) 보고서(0)

전체(0) 논문(0) 특허(0) 보고서(0)

관련 콘텐츠

원문 URL 링크

이 논문과 함께 이용한 콘텐츠

AI-Helper ※ AI-Helper는 오픈소스 모델을 사용합니다.

선택된 텍스트