보고서 정보
주관연구기관 |
연세대학교 Yonsei University |
연구책임자 |
최종술
|
참여연구자 |
문인기
|
보고서유형 | 최종보고서 |
발행국가 | 대한민국 |
언어 |
한국어
|
발행년월 | 1986-03 |
주관부처 |
과학기술부 |
사업 관리 기관 |
연세대학교 Yonsei University |
등록번호 |
TRKO200200011880 |
DB 구축일자 |
2013-04-18
|
초록
▼
고온재료 개발 및 설계에 있어서 재결정현상이 공업적으로 매우 중요하기 때문에, 오래전 부터 많은 연구자에 의해서 재결정 현상에 관한 연구가 수행되어 왔지만, 대부분의 연구가 미량원소 첨가에 의한 고용원소와 석출상의 영향에 관한 것 뿐이고 가장 중요하고 근본이 된다고 생각되는 기지상의 종류가 재결정에 미치는 영향에 관한 연구는 지금껏 국내외를 막론하고 행해진 바 없다.
따라서 본 연구에서는 상온에서 서로 다른 상을 나타낼 수 있고 재결정현상을 조사할 수 있을 정도로 충분한 소성가공성을 갖는 Fe-32% Ni합금을 시료로 선정하고
고온재료 개발 및 설계에 있어서 재결정현상이 공업적으로 매우 중요하기 때문에, 오래전 부터 많은 연구자에 의해서 재결정 현상에 관한 연구가 수행되어 왔지만, 대부분의 연구가 미량원소 첨가에 의한 고용원소와 석출상의 영향에 관한 것 뿐이고 가장 중요하고 근본이 된다고 생각되는 기지상의 종류가 재결정에 미치는 영향에 관한 연구는 지금껏 국내외를 막론하고 행해진 바 없다.
따라서 본 연구에서는 상온에서 서로 다른 상을 나타낼 수 있고 재결정현상을 조사할 수 있을 정도로 충분한 소성가공성을 갖는 Fe-32% Ni합금을 시료로 선정하고, 이것을 상변태 이론에 의거 각종 열처리를 실시하여 처녀오스테나이트, 역변태오스테나이트, 마르텐사이트의 3상을 만든 다음 재결정거동을 경도 측정법으로 조사하였다. 재결정 거동을 조사하기 위해서 35상을 0%-90% 사이의 여러 두께 감소율로 냉간압연 후, 100℃-900℃사이의 여러 온도에서 1시간씩 가열하였으며, 재결정에 필요한 활성화에너지를 구하기 위해서 600℃-740℃ 사이의 여러온도에서 등온 열처리를 행하였다.
이 3상의 재결정온도는 가공도가 증가함에 따라서 감소하며, 동일가공도에서는 마르텐사이트, 역변태오스테나이트, 처녀오스테나이트 순으로 높았다. 그러나 동일경도에서는 역변태 오스태나이트의 재결정 온도는 처녀오스테나이트나 마르텐사이트보다 더 높았다.
재결정에 필요한 활성화에너지는 3상 모두 가공도가 증가함에 따라서 감소하였으며, 동일가공도에서는 마르텐사이트, 역변태오스테나이트, 처녀오스테나이트 순으로 높았다.
Abstract
▼
Recrystallization phenomena are very important in design and development of elevated temperature materials. Most studies of recrystallization have been performed concerning the effects of small amounts of solute atoms or precipitates on the recrystallization behaviors. However, the effect of matrix
Recrystallization phenomena are very important in design and development of elevated temperature materials. Most studies of recrystallization have been performed concerning the effects of small amounts of solute atoms or precipitates on the recrystallization behaviors. However, the effect of matrix phase on recrystallization phenomenon of an alloy has never been studied, even though this is very important and basic study in design of high temperature alloys. In this study, therefore, three different phases, original austenite, reverted austenite and martensite, were prepared by transformation in Fe-32% Ni alloy, and then recrystallization behaviors of these phases have been studied by hardness measurement.
In order to investigate recrystallization behavior, three phases were coldrolled at various deformation degrees up to 90% in reduction of thickness, and annealed at various temperatures between-100 and 900℃ for one hour. For investigation of activation energy of recrystallization, isothermal annealing was carried out at various temperatures from 600 to 740?.
Original austenite and reverted austenite show one step, corresponding to recrystallization phenomenon, in hardness vs. temperature curve. However, martensite consists of two steps in hardness vs. temperature curve : first step is due to reverse transformation from martensite to austenite, and second step recrystallization of the reverted austenite.
Recrystallization temperatures of three phases are decreased with increasing deformation degree, and at the same levels of deformation degree, the recrystallization temperature becomes higher in the order, martensite, reverted austenite, original austenite. At the same levels of hardness, however, the recrystallization temperature is higher in the reverted austenite than in the other two phases.
Activation energy for recrystallization is decreased with increasing deformation degree in all phases, and at the same levels of deformation degree, the value of activation energy becomes greater in the order, martensite, reverted austenite, original austenite.
목차 Contents
- 표지...1
- 1. 서 론...15
- 2. 처녀오스테나이트의 재결정 거동...17
- 2.1 실험방법...17
- 2.1.1 용해및 시편제작...17
- 2.1.2 열처리방법 및 냉간압연...17
- 2.1.3 X-선회절시험 및 경도측정...18
- 2.1.4 광학현미경 및 전자현미경조직관찰...18
- 2.2 실험결과 및 고찰...18
- 2.2.1 광학현미경 조직관찰 및 X-선회절시험...18
- 2.2.2 가공도에 따른 경도변화...19
- 2.2.3 가공도에 따른 재결정거동...19
- 2.2.4 처녀오스테나이트의 재결정에 필요한 활성화에너지...22
- 3. 역변태오스테나이트의 재결정 거동...24
- 3.1. 실험방법...24
- 3.1.1 용해및 시편제작...24
- 3.1.2 열처리 방법 및 시차열분석...24
- 3.1.3 X-선 회절시험...24
- 3.1.4 광학현미경및 TEM 조직관찰...24
- 3.2 실험결과및 고찰...24
- 3.2.1 역변태온도 측정 및 미세조직관찰...24
- 3.2.2 가공도에 따른 경도의 변화...25
- 3.2.3 가공도에 따른 재결정 거동...26
- 3.2.4 역변태오스테나이트와 처녀오스테나이트와의 재결정거동 비교...27
- 3.2.5 역변태오스테나이트의 재결정에 필요한 활성화에너지...28
- 4. 마르텐사이트의 재결정거동...29
- 4.1 실험방법...29
- 4.1.1 용해및 시편제작...29
- 4.1.2 열처리 방법및 냉간압연...29
- 4.1.3 X-선회절 시험및 시차열분석시험...29
- 4.1.4 경도측정및 조직관찰...29
- 4.2 실험결과 및 고찰...30
- 4.2.1 광학현미경, 전자현미경 조직관찰 및 X-선회절시험...30
- 4.2.2 가공도에 따른 경도값의 변화...30
- 4.2.3 가공도에 따른 재결정 거동...31
- 4.2.4 마르텐사이트의 재결정에 필요한 활성화에너지...33
- 5. 결 론...35
※ AI-Helper는 부적절한 답변을 할 수 있습니다.